Canon Vizcam 1000 User manual

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
REVSION 2
MAY 2001 FY8-13E3-020
COLOR LASER
COPIER
1000/1000S/3100

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
IMPORTANT
THE INFORMATION CONTAINED HEREIN IS PUBLISHED BY CANON, INC., JAPAN, AND IS
FOR REFERENCE USE ONLY. SPECIFICATIONS AND OTHER INFORMATION CONTAINED
HEREIN MAY VARY SLIGHTLY FROM ACTUAL MACHINE VALUES OR THOSE FOUND IN
ADVERTISING AND OTHER PRINTED MATTER.
ANYQUESTIONSREGARDINGINFORMATIONCONTAINEDHEREINSHOULDBEDIRECTED
TO THE COPIER SERVICE DEPARTMENT OF THE SALES COMPANY.
COPYRIGHT © 2001 CANON INC.
Printed in Japan
Imprimé au Japon
Use of this manual should be
strictly supervised to avoid
disclosure of confidential
information.
Prepared by
OFFICE IMAGING PRODUCTS QUALITY ADVANCEMENT DEPT.5
OFFICE IMAGING PRODUCTS QUALITY ASSURANCE CENTER
CANON INC.
5-1, Hakusan 7-chome, Toride-shi Ibaraki 302-8501 Japan

COPYRIGHT © 2001 CANON INC. CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
i
INTRODUCTION
This Service Manual provides basic facts and figures needed to service the plain-paper Color Laser
Copier 1000/1000S/3100 in the field. The Color Laser Copier 1000/1000S/3100 may be configured with the
following system devices:
1 Preview Monitor/Preview Monitor Board
2 RDF-E1
3 Editor F1
4 Film Projector B1
5 Stapler Sorter F1
6 Buffer Pass Unit 1
7 Tandem Kit/Tandem Board
8 Control Card V
9 Interface Board B1/B2
10 PS-IPU III
11 IPU II
12 Film Scanner III
13 Copy Data Controller A1 (not available in some areas)
14 Paper Deck (option in Japan)
15 ED Board A1
Of the above, the Editor is covered in this manual.

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
ii
This Service Manual is organized as follows:
CHAPTER 1, “General Introduction,” shows the CLC1000/1000S/3100’s features, specifications, and
step-by-step instructions on how to operate the copier.
CHAPTER 2, “Copying Processes,” shows how the CLC1000/1000S/3100 generates copies while
discussing each of the steps involved.
CHAPTER 3, “Operations and Timing,” explains the CLC1000/1000S/3100’s mechanical system by
function and principles behind its electrical systems in relation to timing of each operation.
CHAPTER 4, “Mechanical System,” explains how to disassemble/assemble and adjust the CLC1000/
1000S/3100.
CHAPTER5,“Installation,”providespointstonotewhenselectingthesiteofinstallationandinstructions
on how to install the CLC1000/1000S/3100.
CHAPTER 6, “Maintenance and Inspection,” provides tables of periodically replaced parts and
consumables/durables as well as scheduled servicing chart.
CHAPTER 7, “Troubleshooting Image Faults/Malfunctions,” provides maintenance/inspection,
standards/adjustments, troubleshooting image faults, troubleshooting malfunctions.
APPENDIX contains a general timing chart, general circuit diagrams, and PCB diagrams.
This Service Manual is accompanied by the Service Handbook, which contains information on how to
maintain and inspect the CLC1000/1000S/3100 through adjustment and troubleshooting work.
Information found in this manual may be updated from time to time for product improvement, and major
updates are communicated in the form of Service Information bulletins.
All service persons are expected to be thoroughly familiar with the contents of this Service Manual, the
Service Handbook, and Service Information bulletins and be ready to respond to the needs of the user
promptly.

COPYRIGHT © 2001 CANON INC. CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
iii
The following rules apply throughout this Service Manual:
1. Each chapter contains sections explaining the purpose of specific functions and the relationship
between electrical and mechanical systems with reference to the timing of operation.
Inthediagrams, representsthepathofmechanicaldrive;whereasignalnameaccompanies
the symbol , the arrow indicates the direction of the electric signal.
The expression “turn on the power” means flipping on the power switch, closing the front cover, and
closing the delivery unit cover, which results in supplying the machine with power.
2. In the digital circuits, ‘1’ is used to indicate that the voltage level of a given signal is “High,” while ‘0’ is
used to indicate “Low.” (The voltage value, however, differs from circuit to circuit.) In addition, the
asterisk (*) as in “DRMD*” indicates that the DRMD signal goes on when ‘0’.
In practically all cases, the internal mechanisms of a microprocessor cannot be checked in the field.
Therefore, the operations of the microprocessors used in the machines are not discussed: they are
explained in terms of from sensors to the input of the DC controller PCB and from the output of the
DC controller PCB to the loads.
The descriptions in this Service Manual are subject to change without notice for product improvement or
other purposes, and major changes will be communicated in the form of Service Information bulletins.
All service persons are expected to have a good understanding of the contents of this Service Manual
and all relevant Service Information bulletins and be able to identify and isolate faults in the machine.

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
iv
System Configuration
[1] [2] [8]
[3] [4]
[7]
[13] [14]
[9]
[10]
[11] [12]
[6][5]
[1] Preview Monitor
[2] RDF-E1
[3] Editor F1
[4] Film Projector B1
[5] Stapler Sorter F1
[6] Buffer Pass Unit 1
[7] Paper Deck (option in Japan)
[8] Control Card V
[9] Interface Board B1/B2, Preview Monitor Borad
[10] PS-IPU III
[11] IPU II
[12] Film Scanner III
[13] Copy Data Controller A1 (not available in some areas)
[14] ED Board A1

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
v
CONTENTS
CHAPTER 1 GENERAL DESCRIPTION
CHAPTER 2 COPYING PROCESS
I. FEATURES ..............................................1-1
II. SPECIFICATIONS ...................................1-2
A. Type ..................................................1-2
B. Mechanisms .....................................1-2
C. Performance .....................................1-3
D. Others...............................................1-5
III. LASER AND SAFETY MEASURES ........ 1-9
A. DHHS ...............................................1-9
B. CDRH ...............................................1-9
C. Points to Note When Handling
the Laser Unit .................................1-10
IV. NAMES OF PARTS................................1-11
A. External View..................................1-11
B. Cross Section .................................1-13
C. Control Panel ..................................1-15
I. IMAGE FORMATION ...............................2-1
A. Outline ..............................................2-1
B. Static Latent Image
Formation Block................................ 2-3
C. Pre-Exposure (step 1) ......................2-3
D. Primary Charging (step 2) ................2-4
E. Laser Exposure (step 3) ...................2-4
F. Development (step 4) .......................2-5
G. Retention/Transfer (step 5) ...............2-6
H. Separation (step 6) ...........................2-7
I. Fixing (step 7)...................................2-7
J. Photosensitive Drum Cleaning .........2-8
II. AUXILIARYPROCESS............................2-9
A. Pre-Primary Charging.......................2-9
B. Pre-Fixing Charging..........................2-9
C. Grounding Roller ............................2-10
D. Static Eliminator..............................2-10
E. Transfer Belt Cleaning ....................2-11
III. LIMITATIONS .........................................2-12
A. Outline ............................................2-12
B. Characteristics................................2-12
CHAPTER 3 OPERATION AND TIMING
I. BASIC MECHANISMS.............................3-1
A. Functional Construction....................3-1
B. Outline of Electrical Circuitry ............3-2
C. Inputs to and Outputs from
Major PCBs ......................................3-3
D. Sequence of Basic Operations .......3-26
II. ORIGINAL EXPOSURE SYSTEM.........3-29
A. Outline ............................................3-29
B. Sequence of Basic Operations
(original exposure system) .............3-30
C. Scanner Motor ................................3-32
D. Changing the Reproduction Ratio ..3-33
E. Controlling the Intensity of the
Scanning Lamp...............................3-34
III. IMAGE PROCESSING SYSTEM ..........3-36
A. Outline ............................................3-36
B. CCD/CCD Driver ............................3-37
C. Analog Image Processing...............3-38
D. Digital Image Processing................3-39
IV. LASER EXPOSURE SYSTEM ..............3-62
A. Outline ............................................3-62
B. Sequence of Operations
(laser exposure system) .................3-64
C. Laser Scanner Motor......................3-65
D. Generating the BD Signal ...............3-66
E. Video Controller ..............................3-67
F. Laser Driver ....................................3-72
G. Image Position Correction ..............3-74
V. IMAGE FORMATION SYSTEM .............3-84
A. Outline ............................................3-84

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
vi
CHAPTER 4 MECHANICAL SYSTEM
I. EXTERNALS AND CONTROLS..............4-1
A. Covers ..............................................4-1
B. Control Panel .................................... 4-3
C. Fans ..................................................4-4
II. DRIVE SYSTEM ....................................4-10
A. Drum Drive System ........................4-10
B. Developing Motor Assembly ...........4-11
C. Pick-Up Drive Assembly ................. 4-12
D. Scanner Drive Assembly ................4-15
E. Fixing Drive Assembly ....................4-18
F. WasteToner Feeding Drive
Assembly ........................................4-19
III. PICK-UP/FEEDING SYSTEM ...............4-21
A. Paper Deck .....................................4-21
B. Pick-Up Assembly ..........................4-27
C. Multifeeder Assembly .....................4-35
D. Duplexing Unit ................................4-37
E. Pre-Fixing Feeding
Assembly ........................................4-38
F. Pre-Duplexing Feeding Assembly ..4-38
G. Delivery/Reversing Assembly .........4-40
IV. TRANSFER UNIT .................................. 4-42
A. Transfer Unit ...................................4-42
B. Transfer Belt Mount.........................4-53
C. Replacing the Separation Paper
Guide Static Eliminating Wire .........4-55
V. EXPOSURE SYSTEM ...........................4-56
A. Original Exposure System.............. 4-56
B. Pre-Exposure System .................... 4-59
VI. LASER SYSTEM ...................................4-60
A. Laser Unit .......................................4-60
B. Image Position Correcting
Mirror Unit.......................................4-64
VII. HOPPER SYSTEM................................4-72
A. Hopper Assembly ...........................4-72
VIII. CHARGING SYSTEM ...........................4-78
A. Primary Charging Assembly...........4-78
B. Separation/Pre-Fixing Assembly ....4-79
IX. PROCESS UNIT SYSTEM ....................4-80
A. Process Unit ...................................4-80
B. Cleaning Assembly.........................4-85
C. Developing Assembly .....................4-87
D. Photosensitive Drum ......................4-90
E. SALT Sensor...................................4-91
F. No.2 Scoop-Up Sheet ....................4-93
X. FIXING SYSTEM ................................... 4-94
A. Fixing Assembly .............................4-94
B. Upper Fixing Cleaner
Assembly ......................................4-102
C. Fixing Lower Cleaning Assembly..4-103
D. Fixing Oil Application Unit.............4-105
XI. ELECTRICAL SYSTEM....................... 4-107
B. Basic Sequence of Operations
(image formation system) ...............3-86
C. Stabilizing Images ..........................3-87
D. Primary Charging
Assembly ........................................3-97
E. Developing Assembly ................... 3-102
F. Cleaning the
Photosensitive Drum ....................3-120
G. Controlling theTransfer Unit
Charging Mechanism....................3-122
VI. PICK-UP/FEEDING ASSEMBLY .........3-127
A. Outline ..........................................3-127
B. Pick-Up Assembly ........................3-130
C. Paper Deck ...................................3-145
D. Duplexing Unit ..............................3-151
E. Transfer Unit .................................3-160
F. Pre-Fixing Feeding .......................3-177
G. Fixing/Delivery Assembly .............3-178
H. Detecting Jams.............................3-189
VII. CONTROL PANEL ............................... 3-192
A. Outline ..........................................3-192
B. Operation......................................3-192
VIII. EDITOR ...............................................3-195
A. Outline ..........................................3-195
B. Operation......................................3-195
C. Zero-Level Adjustment
for Input Coordinates ....................3-197
IX. FANS....................................................3-198
X. POWER SUPPLY................................. 3-201
A. Power Supply................................3-201
B. Protection Mechanisms for the Power
Supply Circuits..............................3-201

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
vii
CHAPTER 5 INSTALLATION
I. SELECTINGTHE SITE ...........................5-1
II. INSTALLATION ........................................5-3
A. Unpacking.........................................5-3
B. Removing the Fixings, Supplying
Fixing Oil, and Changing the
Voltage Rating (240V North
American Model) ..............................5-5
C. SupplyingToner ................................5-7
D. Supplying Starter............................5-15
E. PreventingDeformationof
Externals......................................... 5-19
F. Mountingthe Belt Retaining Members
........................................................5-20
G. Mounting the Developing Bias
Assembly Protection Member.........5-21
H-1.Installing the Paper Deck for
CLC1000 ........................................5-24
H-2.Installing the Paper Deck-H1 ..........5-31
H-3.Checking the Operation of the
Paper Deck .....................................5-33
I. Checking Images and Operations ..5-35
III. RELOCATINGTHE MACHINE ..............5-36
IV. INSTALLING THE ORIGINAL TRAY ......5-38
V. INSTALLINGTHE CONTROL
CARDV .................................................5-39
CHAPTER 6 MAINTENANCE AND SERVICING
I. PERIODICALLY REPLACED PARTS ...... 6-2
II. CONSUMABLES AND DURABLES ........6-5
A. By the Copier’s Hard Counter...........6-5
B. By the Soft Counter in Service
Mode(COUNTER) ............................ 6-7
III. SCHEDULEDSERVICING
PROCEDURE..........................................6-8
IV. SCHEDULED MAINTENANCE CHART..6-9
CHAPTER 7 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS
GUIDETOTABLES .........................................7-1
I. MAINTENANCE AND SERVICING .........7-3
A. Image Adjustment Basic Procedure ....7-3
B.Scheduled Servicing............................7-5
II. STANDARDS AND ADJUSTMENTS.......7-7
A. Image-Related Parts.........................7-7
B. Original Illuminating System ...........7-13
C. Photosensitive Drum-Related Parts 7-16
D. Charging Assembly-Related Parts .7-18
E. Developing Assembly-Related
Parts ...............................................7-19
F. Transfer Belt Unit ............................7-23
G. When Replacing the Pick-Up/
Feeding-Related Parts....................7-25
H. Laser Exposure System .................7-36
I. Fixing Assembly-Related Parts ......7-41
J. Electrical ADJUSTMENT................7-42
III. TROUBLESHOOTING IMAGE
PROBLEMS ...........................................7-52
A. Initial Checks ..................................7-52
B. Standard Image ..............................7-53
C. Test Prints.......................................7-56
D. Troubleshooting Image Faults.........7-65
IV. TROUBLESHOOTING...........................7-88
A. TroubleshootingMalfunctions ......... 7-88
V. TROUBLESHOOTING FEEDING
PROBLEMS .........................................7-140
A. Jams .............................................7-140
B. Feeding Faults ..............................7-148
VI. ARRANGEMENT AND FUNCTION
OF ELECTRICAL PARTS ....................7-149
A. Sensors ........................................7-150
B. Lamps, Switches, Thermistors,
and Heaters ..................................7-156
C. Clutches........................................7-160
D. Solenoids......................................7-162
E. Fans ..............................................7-164
F. Motors...........................................7-166
G. PCBs ............................................7-168

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
viii
APPENDIX
A. GENERAL TIMING CHART.................... A-1
B. SIGNALS AND ABBREVIATIONS .......... A-3
C. GENERAL CIRCUIT DIAGRAM ........... A-11
D. DC CONTROLLER CIRCUIT
DIAGRAM ............................................. A-15
E. READER CONTROLLER PCB............. A-51
F. CCD DRIVER CIRCUIT DIAGRAM ...... A-66
G. HVT CIRCUIT DIAGRAM ..................... A-70
H. SPECIALTOOLS.................................. A-82
I. SOLVENTS AND OILS ......................... A-84
H. Variable Resistors (VR),
Light-Emitting Diodes (LED),
and Check Pins by PCB ...............7-170
VII. SERVICE MODE .................................7-187
A. Outline ..........................................7-187
B. Control Display Mode (DISPLAY) .7-191
C. ADJUST (adjustment)...................7-225
D. FUNCTION (function/inspection)..7-251
E. OPTION (options mode)...............7-286
F. TEST PRINT (test print) ...............7-292
G. COUNTER (counter) ....................7-294
VIII. SELF DIAGNOSIS...............................7-296

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 1
GENERAL DESCRIPTION
I. FEATURES ..............................................1-1
II. SPECIFICATIONS ...................................1-2
A. Type ...................................................1-2
B. Mechanisms ......................................1-2
C. Performance ......................................1-3
D. Others................................................1-5
III. LASER AND SAFETY MEASURES ........1-9
A. DHHS ................................................1-9
B. CDRH ................................................1-9
C. Points to Note When Handling
the Laser Unit ..................................1-10
IV. NAMES OF PARTS................................1-11
A. ExternalView...................................1-11
B. Cross Section ..................................1-13
C. Control Panel ...................................1-15

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
1-1
1. GENERAL DESCRIPTION
I. FEATURES
1. Turns out as many as 30 copies per minute (both full-color and black-and white).
The newly developed mechanism of four photosensitive drums processes 30 copies every minute.
2. 5000-sheet large capacity paper source.
The addition of two cassettes (holding 500 sheets each) and a paper deck (4000 sheets) offers a
source ready to supply 5000 sheets of paper.
3. Automatic duplexing mechanism.
The built-in duplexing unit enables automatic copying on both sides of sheets.
4. Paper of up to 209 g.
Postcards and other materials of heavy stock may be used for copying.
5. Various creative functions.
In addition to such basic creative functions as editing of hue and brightness, installation of the ED
Board A1 provides such complex creative functions as framing, gradation, and freehand.
6. Full line-up of options.
A large number of options are designed for the CLC1000, including the Preview Monitor, RDF, and
IPU-II.

1. GENERAL DESCRIPTION
1-2
COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
II. SPECIFICATIONS
A. Type
Body Console
Copyboard Fixed
Light source Halogen lamp
Lens Lens array
Image reading Photocells (BGR; 3-line CCD); CCD fixed, mirror scanning
Photosensitive medium OPC drum (60 dia.)
Table 1-201
B. Mechanisms
Copying Indirect electrostatographic
Charging Corona
Exposure Laser beam
Contrast adjustment Automatic
Development Toner projection (brush); development in Y, M, C, and Bk
Toner supply Manual (750 g of Y, M, and C; 640 g of Bk)
Pick-up 2 front cassettes (special), paper deck, multifeeder
Retention Static retention (concurrent with Y transfer)
Transfer Blade (transfer belt)
Separation Static
Drum Cleaning Blade
Fixing Heat roller (700 W, upper; 500 W, lower)
Table 1-202

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
1-3
1. GENERAL DESCRIPTION
C. Performance
Table 1-203
Type of original
Maximum original size
Reproduction ratio
Wait time (at 20°C)
First copy time (A4/LTR)
Continuous copying
Copying speed
Cassette
Multifeeder
Paper deck
Cassette
Multifeeder
Paper deck
Two-sidedcopying
Cassette
Multifeeder
Paper deck
Copy tray capacity
Image margin
Non-image width
Main scanning direction
Sub scanning direction
Sheet, 3-D object (2 kg max.)
11"x17" (279 mm x 432 mm)
Direct (±0.5%), default (±1.0%; Table 1-201), Zoom between 25% and
400% (±1.0%, in 1% increments), XY independent Zoom, AMS, XY-
AMS, Zoom program
8 min or less CLC1000/3100 CLC1000S
Plain paper 15.5 sec or less 16.5 sec or less
/transparency 19 sec or less 20 sec or less
18 sec or less 19 sec or less
Up to 999 copies
See Table 1-207.
Max.: 11"x17" (279 mm x 432 mm)
Min.: STMT (216 mm x 139.5 mm)
Max.: 305 mm x 457 mm
Min.: Postcard (special)
LTR (279 mm x 216 mm)
Plainpaper(80to105g/m
2
),transparency(special),Thinpaper(64to79g/m
2
)
Thin paper (64 to 79 g/m2), plain paper (80 to 105 g/m2), thick paper
(106 to 163 g/m2; including cast coated paper, postcard), extra thick
paper (164 to 209 g/m2; including cast coated paper, postcard), special
papers 1 and 2, transparency (special)
Plain paper (80 to 105 g/m2), transparency (special), Thin paper (64 to
79 g/m2)
Plain paper (105 g/m2; automatic two-sided/manual two-sided)
Clawless, center reference, about 500 sheets of 81.4 g/m2
about 250 sheets of 81.4 g/m2
410 mm (stacking height; about 4000 sheets of 81.4 g/m2paper)
250 sheets (approx.)
One-sided Two-sided
Leading edge: 2.5 mm ±1.5 mm Leading edge: 2.5 mm ±2.0 mm
Left/right: 2.0 mm ±1.0 mm Left/right: 2.0 mm ±1.5 mm
Trailing edge: 2.5 mm ±1.5 mm Trailing edge: 2.5 mm ±2.0 mm
One-sided Two-sided
Leading edge: 2.5 mm ±1.5 mm Leading edge: 2.5 mm ±2.0 mm
(0.5 ±0.5 mm in full image mode) (0.5 ±0.5 mm in full image mode)
Left/right: 2.0 mm ±1.0 mm Left/right: 2.0 mm ±1.5 mm
(0 ±1.0 mm in full image mode) (0 ±1.0 mm in full image mode)
Trailing edge: 2.5 mm ±1.5 mm Trailing edge: 2.5 mm ±2.0 mm
400 dpi
400 lpi
Copy size
(paper size)
Paper type

1. GENERAL DESCRIPTION
1-4
COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
Density adjustment
Color mode
Color adjustment
Original mode
Original detection
Cassette selection
Separation
Auto two-sided copying
Binding margin
Frame erasing
Shift
Transparency interleaf
One-touch adjustment
Interrupt
ID mode
Auto start
Auto clear
Auto power-off
Pre-heating
Area selection/non-rectangular area
selection
Freehand selection
Composition
Image create
Color create
Specifications settings
Standard mode change
Mode memory
Timer
Density correction
Auto gradation correction
Background level adjustment
Text/photo level
Zoom fine adjustment
Cleaning
Transparency holder memory
Thin paper source memory
Manual (9 steps), color AE, BE
ACS, black, full-color
Color balance, registration, hue/brightness adjustment, density
range adjustment
Text/printed photo, text/halide photo, text, printed photo, halide
photo, map
Size, position
Auto paper selection, auto cassette change
Page separation, free division, enlargement separation, reduced
page composition (w/ RDF), two-sided separation (w/ RDF)
One-sided to two-sided, two-sided to two-sided (w/ RDF), two-
sided to one-sided (w/ RDF), page separation two-sided
Provided (right/left two-sided binding; margin adjustment)
Original, book, sheet
Center, corner, selection
Provided
Provided
Provided
Provided
Provided
Provided (2-min standard; may be changed or disabled in user mode)
Provided (2-hr standard; may be varied or disabled in user mode)
Provided
Provided (w/ ED Board A1)
Provided (w/ editor)
Provided (w/ ED Board A1)
Provided (some functions w/ ED Board A1)
Provided (some functions w/ ED Board A1)
Provided
Memory/Initialization
9 modes; 3 in full set, 6 in non-area
Auto clear time, auto power-off time
Provided
Provided
Provided
Adjustment of text/photo separation (7 steps)
Provided
Provided
Provided
Provided
Table 1-203
User
mode

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
1-5
1. GENERAL DESCRIPTION
D. Others
For temperature, see Figure 5-1 in Chapter 5.
For humidity, see Figure 5-1 in Chapter 5.
(atmosphere between 810.6 hPa to 1013.3 hPa; 0.8 to 1.0 atm)
Power supply Serial number
200V LFH XXXXXX (CLC1000 JPN)
LKP XXXXXX (CLC2400 JPN)
208V NFH XXXXXX (CLC1000 UL)
NKZ XXXXXX (CLC2400 UL)
NSL XXXXXX (CLC3100 UL)
230V SFH XXXXXX (CLC1000 FRN)
SRQ XXXXXX (CLC1000S FRN)
TFH XXXXXX (CLC1000 GER)
TBS XXXXXX (CLC1000S GER)
UFH XXXXXX (CLC1000 AMS)
UFT XXXXXX (CLC1000S AMS)
PGN XXXXXX (CLC1000 ITA)
PHN XXXXXX (CLC1000S ITA)
PFH XXXXXX (CLC1000 general)
RGT XXXXXX (CLC1000S general)
240V QFH XXXXXX (CLC1000 UK)
QCK XXXXXX (CLC1000S UK)
RFH XXXXXX (CLC1000 CA)
RCM XXXXXX (CLC1000S CA)
Copying: 3 kW or less (approx.; A4, full color, continuous)
Standby: 0.62 kW/h (approx.; reference only)
73 dB (copying) Sound power level by ISO
64 dB (standby) (1 m from machine)
0.02 ppm or less (average over 8 hr)
Keep wrapped and protect against humidity.
Avoid direct rays of the sun; keep at 40°C or less.
Avoid direct rays of the sun.
See Figure 1-201.
486.7 kg (body only)
Copyboard (3.7 kg)
Editor (4.9 kg)
Paper Deck (25.5 kg)
Operating environment
Power supply
Power consumption
Noise
Ozone Paper
Toner
Fixing oil
Dimensions
Weight
Consumables
Table 1-205

1. GENERAL DESCRIPTION
1-6
COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
Figure 1-201
2013mm
(w/ paper deck)
1384mm
2476mm
820mm
(w/ sorter)
(w/ projector)
730mm
Height 1000 mm (w/ copyboard cover)
1172 mm (w/ RDF-E1)
1422 mm (w/ projector)

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
1-7
1. GENERAL DESCRIPTION
Model Reduction
—
A3 →A5
A3 →B5
A3 →A4R
B4 →B5R
B4 →A4R
A3 →B4
A4R →B5R —
—
279 mm x 432 mm (11" x 17")
→LTRR
279 mm x 432 mm (11" x 17")
→LGL
LGL →LTRR
—
A3 →A5
A3 →A4R
—
A3 →A5
A3 →A4R
B4 →B5R
B4 →A4R
A3 →B4
A4R →B5R
Enlargement
B4 →A3
B5R →A4R
B5 →A4
A4R →B4
A5 →B5
A4R →A3
B5R →B4
A5 →A3
—
—
LGL → 279 mm x 432 mm (11" x 17")
—
LTRR →279 mm x 432 mm
(11" x 17")
MINIT →LTRR
—
A4R →A3
A5 →A3 —
B4 →A3
B5R →A4R
B5 →A4
A4R →B4
A5 →B5
A4R →A3
B5R →B4
A5 →A3
—
Table 1-206
0.250
0.500
0.611
0.707
0.815
0.865
0.250
0.500
0.647
0.733
0.786
0.250
0.500
0.707
0.250
0.500
0.707
0.815
0.865
1.153
1.223
1.414
2.000
4.000
—
1.214
1.294
2.000
4.000
—
1.414
2.000
4.000
1.153
1.223
1.414
2.000
4.000
Japanese
6R5E
North American
5R4E
European
3R3E
Others
5R5E

1. GENERAL DESCRIPTION
1-8
COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
Source
Cassette
Paper deck
Duplexing
Multifeeder
Side
One-sided
One-sided
2nd side
One-sided/
2nd side
Paper type
Plain paper
OHP
Plain paper
Plain paper
Plain paper
Thick paper
Extra thick
paper
Transparency
Shine
Matte
Standard
Glossy
Standard
Matte
Standard
Gloss
Standard
Glossy
Standard
Glossy
Standard
Glossy
Standard
Glossy
Standard
Copying speed
A4R/LTR A3/ A4R/B4
279mm x 432mm
(11"x17")
15 6 9
* 31 12 18
* 24
94 6
64 4
15 — —
31 — —
9— —
21 9 12
94 6
21 9 12
94 6
94 6
64 4
64 4
64 4
64 4
Table 1-207 Copying Speed (copies/minute)
Specifications subject to change without notice.
REF.
The CLC1000 varies the fixing
speed to a specific standard to pro-
duce the degree of shine selected
by the user.
A higher fixing speed decreases the
shine, producing a matte effect.On
the other hand, a lower fixing speed
increases the shine, producing a
glossy effect.
* Upper:CLC1000/3100, Lower: CLC1000S