Canon Finisher-R1 Service manual

Nov 27 2003
General Timing Chart / General
Circuit Diagram
Finisher, Sorter, DeliveryTray
Finisher-R1

IMPORTANT
This documentation is published by Canon Inc., Japan, to serve as a source of reference for work in the field.
Specifications and other information contained herein may vary slightly from actual machine values or those found
in advertising and other printed matter.
Any questions regarding the information contained herein should be directed to the Copier Service Department of the
Sales Company.
This documentation is intended for all sales areas, and may contain information not applicable to certain areas.
Reproduction without permission not allowed.
Use of this manual should be strictly supervised to avoid disclosure of confidential information.
COPYRIGHT 2001 CANON INC.
Printed in Japan
Caution
Use of this manual should be strictly supervised to avoid disclosure of confidential information.

Contents
1 Genelal Timing Chart............................................................................................................................................... 1
Finisher Unit............................................................................................................................................................ 1
2 General Circuit Diagram .......................................................................................................................................... 3
Signal Names........................................................................................................................................................... 3
General Circuit Diagram ......................................................................................................................................... 5

1
1 Genelal Timing Chart
Finisher Unit
■Stapling : A4 size paper, 2-sheet document, rear1-point stapling
F-1-1
down
up up
down down
up up up
down up
Alignment
1
2
4
3
5
6
8
7
9
10
12
11
13
14
16
15
17
18
19
Inlet sensor (PI33)
Feed path sensor (PI34)
Stack ejection roller (M32)
1st delivery roller alienate
solenoid (SL33)
Stack ejection lower roller clutch
(CL32)
Rear aligning plate motor (M34)
Front ligning plate home position
sensor (PI36)
Front aligning plate motor (M33)
Swing unit home position sensor
(PI35)
Rear end assist guide home
position sensor (PI39)
Staple motor (M41)
Paper surface sensor (PI41)
Tray 1 shift motor (M37)
Stapler shift motor (M35)
Swing motor (M36)
Stapler shift home position
sensor (PI40)
Operation
Inlet motor (M31)
Rear ligning plate home position
sensor (PI37)
Rear end assist motor (M39)
Host machine eject signal
Operation start signal
CW CCW
Retract Alignment Retract Retract
Retract

3
2 General Circuit Diagram
Signal Names
List of Signal Names/Abbreviations (Finisher Unit)
The following presents the abbreviations of signals used in this manual and in drawings, and the meaning of each signal.
Reference: Signals enclosed by brackets [ ] are electrical signals, However, the state “1” or “0” of these analog signals cannot be indicated. Otherwise, the state of digital signals “1” or “0” can be indicated.
T-2-1
ASSIST-HP REAR END ASSIST GUIDE HP DETECT Signal
BIND-CL STACK EJECTION LOWER ROLLER CLUTCH DRIVE Signal
BUFF-P-SL BUFFER REAR END HOLDING SOLENOID DRIVE Signal
BUFF-
ROL-SL
BUFFER ROLLER ALIENATE SOLENOID DRIVE Signal
DELIV-
ROL-SL
1ST DELIVERY ROLLER ALIENATE SOLENOID DRIVE Signal
F-COVER FRONTCOVER OPEN/CLOSE DETECT Signal
F-COVER-
SW
FRONT DOOR CLOSED DETECT SWITCH Signal
FJOG-HP FRONT ALIGNMNT PLATE HP DETECT Signai
G-
CHANGE-
HP
GEAR CHANGE HP DETECT Signal
INLET INLET PAPER DETECT Signal
INLET-
ROL-SL
INLET ROLLER ALIENATE SOLENOID DRIVE Signal
JOGTRY-P PROCESSING TRAY PAPER DETECT Signal
RJOG-HP REAR ALIGNMNT PLATE HP DETECT Signal
SHUT-CL SHUYYER OPEN/CLOSE CLUTCH DRIVE Signal
SHUT-HP SHUTTER HP DETECT Signal
STP-HP STAPLER HP DETECT Signai
STP-
INFERE
STAPLER ALIGNMENT INTERFERENCE DETECT Signal
STP-LS HOOK EMPTY DETECT Signai
STP-
READY
HOOK TOP POSITION DETECT Signai
STPSFT-
HP
STAPLER SHIFT HP DETECT Signal
STP-SW CARTRIDGE DETECT SWITCH Signal
SWG-HP SWING GUIDE HP DETECT Signai
SWG-SW SWING GUIDE OPEN DETECT SWITCH Signal

4
TIMMING FEED PLATE PASS PAPER DETECT Signal
TRY1-
AREA1
TRAY 1 AREA DETECT Signal 1
TRY1-
AREA2
TRAY 1 AREA DETECT Signal 2
TRY1-
AREA3
TRAY 1 AREA DETECT Signal 3
TRY1-P TRAY 1 PAPER DETECT Signal
TRY2-
AREA1
TRAY 2 AREA DETECT Signal 1
TRY2-
AREA2
TRAY 2 AREA DETECT Signal 2
TRY2-
AREA3
TRAY 2 AREA DETECT Signal 3
TRY2-P TRAY 2 PAPER DETECT Signal
TRYSFT2-
P
TRAY 2 PAPER SURFACE DETECT Signal
UP-
COVER
UPPER COVER OPEN/CLOSE DETECT Signal
UPPER-P PAPER SURFACE DETECT Signal
UPPER-
TRY
TRAY 1 CLOSED DETECT SWITCH Signal