Canon Creative Park Clowns on Stilts Line Dance User manual

(Moving) Clowns on stilts line dance : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & unity design
http://www.canon.com/c-park/en/
*When you pull on the lever at right,
the long-legged clowns begin to dance,
with all three clowns lifting their long
legs and the puppy ducking its head.
Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold.
Valley fold(dashed and dotted line)
Make a valley fold.
Scissors line(solid line)
Cut along the line.
Cut in line(solid line)
Cut along the line.
Glue spot(Red dot)
Glue parts with the same number together.
Glue spot(Green dot)
Glue within the same part.
Glue spot(Blue dot)
Glue to the rear of the other part.
Glue
The glue spot(colored dot)
shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
View of completed model
Assembly Instructions : Eleven A4 sheets (No. 1 to No. 11)
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.
Before starting assembly : Writing the number of each section on its back side
before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after cutting out
the sections.)
Indicates where sections should
be glued together.
Indicates where to insert sections.
Do not glue the sections together.
Cut along the line.
Use care here.
Round bar : Use to give parts a curved surface.
Tweezers : Useful in working with fine parts.
Caution: This circus clown dance model uses three pieces of thread.
Please use strong thread such as silk thread (three pieces 30 cm each in length).
Caution: Do not assemble the parts into a box shape yet at this stage.
Turn the parts upside down and glue them
in place as shown in the illustration.

(Moving) Clowns on stilts line dance : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & unity design
It's easier to form a
cylinder using a round
bar or similar object.

(Moving) Clowns on stilts line dance : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & unity design
Pull the openings in parts 18, 19, and
20 shown above slightly forward.
Insert the glue spots to be glued
on parts 19 and 20 and glue
them in place.

(Moving) Clowns on stilts line dance : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & unity design
Parts
18 to 20, 23, and 24

(Moving) Clowns on stilts line dance : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & unity design
Pull and push the lever at right to check
the movement of part 25 at left.
These steps are easier if you use an empty box or similar
item as a base and assemble the parts upside down.

(Moving) Clowns on stilts line dance : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & unity design
Before gluing these parts in place,
first check the positions and directions
in which you will glue them.
Caution: Spread only a thin layer of glue
to ensure that the model surface
does not become warped.
Caution: Do not glue the bottom of
the base (box) in place yet
at this stage.
Insert the lever through the cross-shaped
opening.
Parts 36 (46, 56)
Use pieces of thread each about
30 cm in length (use a total of
three pieces of thread).
Parts 33 (43, 53)
Parts 37 (47, 57)
Insert a thread into the
opening and tie the end of it.
Caution: Glue together the clown legs assembled
as shown on page 7 carefully, to ensure
that they do not become warped.

(Moving) Clowns on stilts line dance : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & unity design
Parts 28, 31, and 32 Parts 29 and 31
Parts 36 and 37 Parts 33 and 34
Parts 30 and 38

(Moving) Clowns on stilts line dance : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & unity design
First glue the glue spots
on part 30 (42, 52).
Place the left and right legs together in position,
leaving no gap between them, and glue them to
part 34 (the cylindrical axle).
Run the thread through the left leg,
so that it sticks out from the bottom.
Pull the thread to check the
movement of the clown's leg.
Assemble the other two clowns in the same way
you assembled the clown in orange.

(Moving) Clowns on stilts line dance : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & unity design
Fold the fold line ( ) on the puppy
forward and backward five or six
times, so that it will move easily.
Glue parts 63 and 64 in place, aligned with the tip
of the puppy's nose on the reverse side of part 60.
Parts 60, 63, and 64
Use your finger to check
the movement of the puppy's head.
Caution: Push the puppy's upper body forward
touches the surface of the base (box)
and then glue the upper body to
the puppy's legs in this position.

After running the thread for each clown
through the opening in the base, glue the
clown to the base.
Caution: Do not glue the bottom in place yet.
When gluing the puppy in place,
first glue the rear glue spot in place
and then the left and right spots,
one at a time.
(1)Push the lever in as far as it will go.
(2)Pull the thread gently beneath the cylinder
(axle) and then insert it into the opening.
(4)Glue part 21 in place to fix
the thread firmly in position.
(3)
Wrap the thread around the opening once,
then adjust the length of thread by pulling on
the lever to see how the leg moves.
(Moving) Clowns on stilts line dance : Assembly Instructions ©Canon Inc. ©Hideharu Naitoh & unity design
About 5 mm
The right leg should rise from a
position in which the left and right
heels are together to about 5 mm
beyond the tip of the puppy's cap.
Ensure the legs of all three clowns
rise to the same height.