Canon Creative Park Nikko Toshogu Shrine Yomeimon User manual

Mountain fold(dotted line)
Make a mountain fold.
Glue spot (Red dot)
Glue parts with the same number together.
Glue spot (Green dot)
Glue whithin the same part.
Glue spot (Blue dot)
Glue to the rear of the other part.
Glue spot (White circle)
Attach to the edges of the other parts.
Trace along the folds with a
ruler and a used pen (no ink) to
get a sharper, easier fold.
Glue, scissors and other tools
may be dangerous to young
children so be sure to keep them
out of the reach of young
children.
Scissors, set square, glue (We
recommend stick glue),pencil,
used ballpoint pen, toothpicks,
tweezers,
(useful for handling small parts)
The glue spot(colored dot)
shows where to apply the glue.
Assembly tip CautionAssembly Instructions Tools and materials
Nikko Toshogu is a shrine in Nikko City, Tochigi Prefecture. It was designated as a World
Heritage Site in 1999.
"Yomeimon", a gate that is the most well-known section of Nikko Toshogu, is adorned with
approximately 500 engravings and richly-colored decorations representing the stylishness of
the Edo culture. It is also called "Higurashimon", meaning "gate of sundown", because of its
sophistication and splendor that continue to take your breath away even after gazing at it all
day long.
Parts sheet (Pattern) : Twenty-two A4 sheets
No. of Parts : 411 parts
Assembly Instructions : Sixteen A4 sheets
* Build the model by carefully reading the Assembly Instructions, in the parts sheet page order.
Hint
*This model was designed for Papercraft and may differ from the original in some respects.
*In this picture, the edges of the completed model have been touched up with paint.
Valley fold
(dashed and dotted line)
Make a valley fold.
Scissors line (solid line)
Cut along the line.
Cut In Line (solid line)
Cut along the line.
Write down the number on the back of each part as you cut them out.
Since many of the parts are complicated and very small, do a trial assembly before actually
attaching them together.
The finished piece will look more realistic if you paint the edges of the parts with colors similar
to the parts.
PAGE01
Nikko Toshogu Shrine (Yomeimon) : Assembly Instructions

1D
1F
1L
1P
1P
1N
1N
Fold and cut out.
Where to attach 1N and 1P.
1H
1L
1J
Complete
Assembling the handrail (right side)
Use the 2nd page of the parts sheet.
Assemble 1D and 1H.
There are thirteen 1Ls; attach them to 1F and 1J.
Assemble the parts made in to 1D and 1H.
Connect 1H to the assembled 1D.
Assemble 1N and 1P. Then, attach them
to the glue tabs that were connected in .
PAGE02
Nikko Toshogu Shrine (Yomeimon) : Assembly Instructions

1E
1F
1M
1O
1Q
1Q
1O
Fold and cut out.
Where to attach 1O and 1Q.
1I 1M
PAGE03
Complete
1K
1G
Assembling the handrail (left side)
Use the 2nd page of the parts sheet.
Assemble 1I and 1E.
There are thirteen 1Ms; attach them to 1G and 1K.
Assemble the parts made in to 1I and 1E.
Connect 1E to the assembled 1I.
Assemble 1O and 1Q. Then, attach them to the glue tabs
that were connected in .
Nikko Toshogu Shrine (Yomeimon) : Assembly Instructions

4B
4A
5A
3B
2B
3A
2A
1A
1C
1B 4C
3C
6A
Assembling the base.
Use 2nd to 7th pages of the parts sheet.
Assemble 2A and 2B, 3A and 3B, and 4A and 4B. Then, attach them all.
Attach the three parts assembled in into a U-shape.
Assemble 5A with the parts attached in .
Attach Stone Steps 6A to the parts made in .
After attaching 6A, attach 3C and 4C to its back side.
(These are pieces to reinforce the base.)
Finish making the stone steps by attaching 1C and 1B to 1A,
and assemble to the base(2A, 2B).
Attach the handrail part you made on the previous page
to 6A.
PAGE04
Nikko Toshogu Shrine (Yomeimon) : Assembly Instructions

7K
7F
7G
7H
7C
7D
7E
Using a thin, round stick to roll
the piece will result in a neat finish.
7C ~ 7H
9B
Complete
7A
7B
7I
7J
7L
7L
7Q
7Q
7R
7R
7B
7O
7P
9G 9E
PAGE05
Assembling the 1st floor part (right side)
Use the 8th and 10th pages of the parts sheet.
Fold 7L along the fold lines, attach the back side, and attach 7Q and 7R
(which you have made into square tubular shapes) to the respective
glue tabs (make four sets).
Attach each 7L to 7I. Then, assemble 7O and 7P and attach them to 7I.
Attach Person 9G, Lion 9E, and Partition 7J to 7I.
Assemble the 7B parts and attach each to 7A.
Attach all the parts you made up to step with the parts of .
Roll all the parts (7C-7H) and apply glue to make the pillars.
Slot the pillars (7C-7H) onto the cut lines on 7O, 7P, and 7R and glue them in place.
Also, assemble the horizontal Pillar 7K and attach it.
Assemble 9B, slot it onto the cut lines on the pillars (7C-7H), and glue it in place.
Nikko Toshogu Shrine (Yomeimon) : Assembly Instructions

8K 8F
8G
8H
8C
8D
8E
8B
8I
8J
8L
8L
8Q
8Q
8R
8R
8B
8O
8P Using a thin, round stick to roll
the piece will result in a neat finish.
8C ~ 8H
9C
9H
9F
8A
Complete
PAGE06
Assembling the 1st floor part (left side)
Use the 9th and 10th pages of the parts sheet.
Fold 8L along the fold lines, attach the back side, and attach 8Q and 8R
(which you have made into square tubular shapes) to the respective
glue tabs (make four sets).
Attach each 8L to 8I. Then, assemble 8O and 8P and attach them to 8I.
Attach Person 9H, Lion 9F, and Partition 8J to 8I.
Assemble the 8B parts and attach each to 8A.
Attach all the parts you made up to step with the parts of .
Roll all the parts (8C-8H) and apply glue to make the pillars.
Slot the pillars (8C-8H) onto the cut lines on 8O, 8P, and 8R and glue them in place.
Also, assemble the horizontal Pillar 8K and attach it.
Assemble 9C, slot it onto the cut lines on the pillars (8C-8H), and glue it in place.
Nikko Toshogu Shrine (Yomeimon) : Assembly Instructions

Diagram a
7N(8N)
7M(8M) 1st floor part
9I
9DA
9DB
9A
PAGE07
Assembling the 1st floor part
Use the 8th to 10th pages of the parts sheet.
Assemble 7N (8N) and 7M (8M) and attach them to the right-hand
and left-hand sides of the first floor section.
Attach the right and left sides of the first floor section to the base.
Assemble parts 9DA, 9DB and 9I, and attach them
between the parts on the right and left.
Referring to Diagram a, attach the engravings from
page 10 to the 14 areas on the corresponding pillars by
matching the numbers (assemble two parts for each).
Assemble 9A and attach it by placing it over the first floor section.
Nikko Toshogu Shrine (Yomeimon) : Assembly Instructions

10C,10D
10A,10B
10E,10F
10G,10H,10I,10J
PAGE08
Assembling the Walls
Use the 11th page of the parts sheet.
Fold parts 10G to 10J (mountain fold) in half to assemble them.
Assemble 10A and 10B, 10E and 10F, and 10C and 10D and attach them as shown in the diagram.
Attach the two assembled parts to the base.
Nikko Toshogu Shrine (Yomeimon) : Assembly Instructions

When attaching the piece to 13B, align the strips neatly.
View from the back side
11A
11B 11C
11D
11E
11F
12A
12B
12C
12D
12E
12F
13B
13A
As for the corners,
attach the strips together.
Diagram b
11J,12J
Position it around
the back side.
11A
11B 11C
11D
11E
11F
12A 12B
12C
12D
12E
12F
13B
PAGE09
Since the part to be folded is very narrow,
using a ruler to do so will help.
Assembling the area between the first and second floors
Use the 12th to 14th pages of the parts sheet.
Before attaching all the parts (11A (12A)-11F (12F)), fold each along the fold lines.
When attaching the parts to 13B, attach them by starting from the outer side
11A (12A) to the inner side 11F (12F). Attaching the parts will be easy if you
attach them after connecting them into a box-shape.
After attaching the parts to 13B, start attaching the strip-like parts to the inner-
side parts. As for the strips that end up in the corners, attach them to each otheras shown in the diagram.
Attach engravings 11G (12G)-11I (12I) to 11C (12C). Insert the slit on the back into 11A (12A).
As shown in the diagram, attach the back sides together by positioning Engraving 11J (12J) around the strips on the corners.
Finally, attach the back sides of 13A and 13B.
Nikko Toshogu Shrine (Yomeimon) : Assembly Instructions

Slot the slits on the top and
bottom of the pillar like this.
Diagram a
Using a thin, round stick to roll
the piece will result in a neat finish.
14G ~ 14P
14A
14B
14C
13A
14E
14F
14D
PAGE10
Assembling the second floor section
Use the 15th and 18th pages of the parts sheet.
Assemble the pillars(14G-14P).
After connecting 14A and 14B and forming them
into a box-shape, slot each pillar onto the cut lines.
Attach 14A (14B), with the pillars slotted on, to 13A.
Attach 14E and 14F to the back sides of 14C and 14D respectively.
Then, attach them to 13A.
Assemble engravings 17F-17S and attach them to the glue tabs
on the upper part of the pillars.
Nikko Toshogu Shrine (Yomeimon) : Assembly Instructions