Canon CREATIVE PARK (Moving) Clowns out of a... User manual

(Moving) Clowns out of a cannon : Assembly Instructions
* When you pull the lever on
the right, a clown shoots out of
the cannon. It is a fun craft.
Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold.
Valley fold(dashed and dotted line)
Make a valley fold.
Scissors line(solid line)
Cut along the line.
Cut in line(solid line)
Cut along the line.
Glue spot(Red dot)
Glue parts with the same number together.
Glue spot(Green dot)
Glue within the same part.
Glue spot(Blue dot)
Glue to the rear of the other part.
Glue
The glue spot(colored dot)
shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
View of completed model
Assembly Instructions : Fifteen A4 sheets (No. 1 to No. 15)
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
* Build the model by carefully reading the Assembly Instructions, in the parts sheet page order.
Before starting assembly : Writing the number of each section on
its back side before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after
cutting out the sections.)
Indicates where sections should be glued together.
Indicates the order for assembling parts.
Indicates where to insert sections.
Do not glue the sections together.
Round bar : Use to give parts a curved surface.
Tweezers : Useful in working with fine parts.
Be sure to build
this model carefully.
http://www.canon.com/c-park/
Parts 1 and 2
Firmly form the shape as you
glue to prevent distortion.

(Moving) Clowns out of a cannon : Assembly Instructions
Spread glue in a thin,
even layer before gluing
surfaces together.
Glue one side of the shaft (Part 11),
and then check if the Parts 1
+ 2 go through the center
of the rectangular hole
in Part 10.
Then glue the other
side.
Parts 5 to 7
Parts 5 to 7
Parts 1 and 2

(Moving) Clowns out of a cannon : Assembly Instructions
Slightly shift the edges of
the slit to the left and right.
Push and pull the lever
to check the movement.

(Moving) Clowns out of a cannon : Assembly Instructions
Curl the section of Part 14
that will form a cylinder with
a round bar.
Parts 14 and 15
Parts 14 and 15 Parts 14, 15 and 17
Roll Part 17 tightly,
insert into Parts 14 +15
and then unroll.
Glue together to the pasting
margins of Parts 14 and 17.
Note : Do not apply glue to parts
other than the pasting margins.

(Moving) Clowns out of a cannon : Assembly Instructions
Parts 14, 15 and 17
Parts 14 to 19
Insert the tip of Part 14 into
Part 16 and glue.

(Moving) Clowns out of a cannon : Assembly Instructions
Parts 14 to 19
Glue the cannon battery
(Part 21) to the pasting
margins on both sides of
Part 10.
Then, glue the semi-circular
pasting margins in the front
and rear.
Prepare part 4 in the same way.

(Moving) Clowns out of a cannon : Assembly Instructions
Parts 1 to 12 and 14
to 19 and 24
Glue the 4 corners of the
top board of the base.
Work on a flat surface to prevent
distortion of the base.
Glue 3 sides of the base (rear, right and left sides).
Note : Do not glue the front side (Part 29) at this point yet.

(Moving) Clowns out of a cannon : Assembly Instructions
Firmly form the shape as you glue
to prevent distortion.
For the clown’s head, glue in the
order of the hair, hat, chin and nose.
Pull the lever and glue the clown’s legs
(front) to Part 1.
Parts 22 and 23

(Moving) Clowns out of a cannon : Assembly Instructions
Prepare 2 strings.
Tightly knot the 2 strings at
around 5 to 6cm from the top.
Wind the string on the slit
of Part 39 and glue.
Note : Make sure the lengths
from the 2 Parts 39 to
the knot are the same.
Note : Do not glue
this part.
Length: 30cm: 1 string
10cm: 1 string
Approx. 4cm
Glue only the bellows section.
Bend the hand and arm slightly toward
you and glue.
Prepare part 38 in the same way.

(Moving) Clowns out of a cannon : Assembly Instructions
Parts 38 and 39
Parts 34 to 36
Pass the triangular prism
through the hole in the arm
and attach so that the arm
covers the shoulder.
Parts 37 and 39