Canon Creative Park Elastic-powered Turtle User manual

1. Carefully cut out the parts.
2. Fold along the dotted lines, making mountain
or valley folds as indicated.
3. Attach the glue spots on each part together.
4. Glue the parts together, and you’re done!
*Please read the Assembly Instructions
carefully before you begin.
Tools
Scissors
Glue (We recommend quick-drying paper glue)
3 rubber bands (preferably brand new ones)
Actual size illustration:
check the size of your rubber bands here.
How to assemble your model neatly
Scoring along the fold lines in advance with a dried
up pen or a ruler with slightly sharp corners will result
in a neater model.
*Be careful not to press too hard as the paper may tear.
Caution
Keep scissors and glue away from small children.
Be careful not to cut your fingers when using scissors.
Scissors line
Cut in line
Glue spot
Notation Key
Assembly Instructions
About 1.57 inches in diameter
Mountain fold
Valley fold
Elastic-powered Turtle : Assembly Instructions

After gluing parts J and K together back to back,
attach the ring you have made.
Assemble all four in the same way.
Assemble the tires
Glue Glue
Fold in half along the fold lines,
glue together at the back and make a ring.
Adding curves to the part first will make it
easier to form a ring.
Back
Assemble the axle
Glue down the end after rolling.
Wind part H around and glue it down.Add curves by pressing and rolling it
against the corner of a table,
with the printed side face up.
Fold the edge to make a triangular prism,
and roll the piece up to form a stick
(about 4mm wide).
Attach part A, enveloping it
around the parts you cut
and bent back.
Attach the other side too.
View from above
Cut three, equally-spaced slots in both ends
of part C, up to the red valley fold line,
and bend them back.
*The fine strips of paper are thick and hard
so be careful of paper cuts.
Attach part M to both ends.
Follow the same process to
assemble the other axle.
Glue
Elastic-powered Turtle : Assembly Instructions

Attach the tires to both ends of the axle.
Make one more in the same way.
*Do not attach a rubber band to the other axle.
*The wheels with the rubber band should be
at the back, and the wheels without at the front.
Assemble the front and back wheels
If necessary, cut off the ends.
Tie one end of the band
to the band stopper,
and the other end
to the middle of the axle.
Cut the rubber band
to make a string.
Assemble the head and tail
Do not attach. Do not attach.
Glue together as shown in the diagram,
and assemble the turtle's head.
Glue together as shown in the diagram,
and assemble the turtle's tail.
Assemble the body
Glue together as shown in the diagram,
and assemble the turtle's body.
Glue and connect
parts E, F and G together.
Elastic-powered Turtle : Assembly Instructions

Attach the wheels
Fold along the fold lines
and glue together
at the reverse side.
Glue
Being careful not to mix up the front and back wheels,
put the axles into the grooves on the body.
Check that the wheels spin smoothly.
Attach. Attach.
Feed the band stopper through the hole
at the front of the body to the outside.
Be careful that the band doesn't come undone.
When you have got the band stopper out,
glue it in place as shown in the diagram,
and wind the wheel band around the back wheels
(the tires furthest from the band stopper).
Assemble together
Attach the turtle's head and tail
to the completed body, and you're done!
After turning the turtle's body over,
glue the tummy to it.
Elastic-powered Turtle : Assembly Instructions

How to play
Pull the car backwards along the ground, gently
pushing down on the back wheels.
Point the car in the direction you want it to run,
let it go and watch it take off!
Be careful not to wind the band too tightly
as it may snap or come untied.
Play with it on a flat surface such as a table or the floor
(wooden floorboards work better than carpet).
If your car doesn't run well, check the following points to repair it.
Are the axles or tires stuck against the body? Are the wheels or tires bent?
Has the band lost its elasticity? Is the band wound up too tightly?
Has the band come loose from the tire? Is the band tangled up around the axle?
Elastic-powered Turtle : Assembly Instructions