Canvas Anderson Credenza User manual

MODEL NO. 068-7827-2
ASSEMBLY INSTRUCTIONS
Toll-free 1-888-670-6684
IMPORTANT: Please read this manual carefully before beginning assembly of this product.
Keep this manual for future reference.
ANDERSON CREDENZA

2MODEL NO. 068-7827-2
Important Safety Instructions 2
Parts List 3-6
Assembly 7-31
Warranty 32
IMPORTANT SAFETY INSTRUCTIONS TABLE OF CONTENTS
Warning! To reduce the risk of serious injury, read the following safety
instructions before assembling and using the dining table.
• This product is intended for domestic indoor use only.
• The product should be placed on a flat horizontal surface.
• Arrange necessary manpower when assembling or moving the product.
• Do not push furniture, especially on a carpeted floor. Have someone help you lift heavy items and set it
in place.
• Check all screws periodically for tightness. When required, tighten them again.
Needed for Assembly
Hammer
2 people
No. 2 Phillips Screwdriver
Tip Shown Actual Size

3
PARTS LIST
Right End - 1
A
Left End - 1
B
Upright - 1
C
Top - 1
D
Bottom - 1
E
Back Rail - 1
F
Skirt - 4
H
Shelf - 1
J
Left Front/Right Rear Foot - 2
L
Brace - 2
G
Back - 1
I
Right Front/Left Rear Foot - 2
K

MODEL NO. 068-7827-2
4
Center Foot - 2
M
Door - 2
N
Top Drawer Front - 1
O
Drawer Front - 2
P
Top Right Drawer Side - 1
Q
Top Left Drawer Side - 1
R
Top Drawer Back - 1
T
Left Drawer Side - 2
V
Drawer Back - 2
X
Drawer Brace - 2
Y
Top Drawer Bottom - 1
S
Right Drawer Side - 2
U
Drawer Bottom - 2
W
PARTS LIST

5
Extension Rail - 6
1
Extension Slide - 6
2
Extension Set shown separated
Large Hidden Cam- 38
3
Small Hidden Cam - 12
4
Angled Head Cam Screw - 38
5
Straight Head Cam Screw - 12
6
Short Wood Dowel - 4
8
Metal Pin/Rubber Sleeve Set - 4
10
Angled head
Straight head
Hinge Bracket - 4
12
Long Wood Dowel - 40
7
Cover Card - 1
9
Drawer Bracket Set - 2
11
PARTS LIST

MODEL NO. 068-7827-2
6
Bumper - 2
Ballast - 1
16
14
13
15
Washer - 4
Hinge - 4
Nail - 48
Black 1-1/2" Flat Head Screw - 30
19
17
18
Black 2-9/16" Bolt - 4
Black 1/2" Wafer Head Screw - 4
Silver 1/2" Flat Head Screw - 8
23
21
20
22
Black 1/2" Pan Head Screw - 36
Black 13/16" Wafer Head Screw - 6
99
Furniture Tipping Restraint Kit - 2
PARTS LIST

ASSEMBLY
D
Step 1
Requires D, 5, 7
NOTE: Two people are needed to build this unit.
Turn two ANGLED CAM SCREWS (5) into the TOP (D).
Insert four LONG WOOD DOWELS (7) into the short edges of the TOP (D).
7
Rounded edge
7
7
Surface with more holes
5
Angled head
Angled head
5 7

8MODEL NO. 068-7827-2
Step 2
Requires D, F, 7, 19
Insert three LONG WOOD DOWELS (7) into the BACK RAIL (F).
Fasten the TOP (D) to the BACK RAIL (F). Use four BLACK 1-1/2" FLAT HEAD SCREWS (19).
NOTE: Be sure the LONG WOOD DOWELS in the BACK RAIL insert into the TOP.
7
D
F
7 19
19
Surface with larage holes
Surface with CAM SCREWS
ASSEMBLY

9
Step 3
Requires E, 5, 7
Turn fourteen ANGLED CAM SCREWS (5) into the exact holes shown in the BOTTOM (E).
Insert six LONG WOOD DOWELS (7) into the short edges of the BOTTOM (E).
E
Angled head
5 7
Surface with more holes
Finished edge
5
7
7
Angled head
ASSEMBLY

10 MODEL NO. 068-7827-2
Step 4
Requires H, K, L, M, 3, 5, 7
Turn four ANGLED CAM SCREWS (5) into the exact holes shown in the FEET (K, L, and M).
Insert four LONG WOOD DOWELS (7) into the FEET (K, L, and M).
Insert two LONG WOOD DOWELS (7) into the SKIRTS (H).
Insert four LARGE HIDDEN CAMS (3) into the SKIRTS (H).
Fasten two SKIRTS (H) to the FEET (K, L, and M). Tighten four LARGE HIDDEN CAMS.
NOTE: Be sure the LONG WOOD DOWELS in the FEET insert into the SKIRTS.
Repeat this step for the remaining SKIRTS (H) and FEET (K, L, and M).
H
H
Angled head
5 73
321
The arrow must
point toward the
edge of the board.
3
3
K
M
L
7
5
5
Angled head
ASSEMBLY