Car Solutions QVL-E65-V2 User manual

BMW E65
Specification & Installation
Compatible with BMW 7 Series(E65/66)
Last updated: 2014.02.14
Model : QVL-E65-V2 / Product code : BM-0901-652
Car-solutions.com
www.car-solutions.com
[email protected]

Contents
2
3. Installation
3.1 Pre-installation Notices
3.2 CAN Installation
3.3 Installation
17
18
4. Troubleshooting 20
1. Before installation
1.1 Main specification
1.2 Features
1.3 System diagram
1.4 Components
1.5 Exterior
1.6 POWER cable
4
3
5
6
7
8
2. Setup
2.1 DIP switch
2.2 Keypad usage
2.3 Remote control usage
2.4 Factory mode
2.5 OSD (on screen display)
2.6 Parking guide line
2.7 BMW Handle button NAVI setting
9
11
12
14
15
16
19
13
Car-solutions.com
www.car-solutions.com
[email protected]

1.1 Main specification
3
1. Input Spec. (MULTI VIDEO INTERFACE)
-. 1 x Analog R,G,B (Sync on Green)
-. 1 x CVBS(REAR CAMERA) Input
-3 x A/V (NTST & PAL) Input
-. 1 x LCD Input (Car system Input)
2. Output Spec.
-. 2 X CVBS OUTPUT
-. 1 x Audio OUTPUT
-. 1 X LCD OUTPUT(LCD Operation)
3. Electric Power Consumption
- Input Power : 8VDC ~ 24VDC
- Consumption Power : 12WATT, Max
4. Switching Mode (AV source)
- Able to skip AV source while switching Mode (AV source) by DIP S/W(Refer to the DIP S/W page)
- By ‘SET’ button of the OSD Keypad
- By Toggle Switch (Option)
- By ‘Menu’ button of the car through CAN
※This function may not support E65 old version which is without “Menu button”
Car-solutions.com
www.car-solutions.com
[email protected]

1.2 Features
4
- Provided OSD Keypad or Remote control
- Move Navi display position(Only on RGB mode)
- Changed OSD MENU
Car-solutions.com
www.car-solutions.com
[email protected]

1.3 System diagram
5
DISPLAY
(CAR MAIN BOARD)
A/V 1
NAVIGATION Input
(Analog RGB)
CVBS IN
(Rear camera)
Car Screen Input
A/V 2
A/V 3 VIDEO
CIRCUIT
VIDEO MUX
MCU
Power Input
(+8VDC ~ +18VDC)
POWER
CIRCUIT
Dip S/W
A/V OUT HEADREST
MONITOR
Switch for source toggle
OEM NAVI Button (Can Interface)
Car Installation
OEM LCD
Rear Camera
(Video out 2
Audio L, R1)
OSD keypad
Or Remote control
Car-solutions.com
www.car-solutions.com
[email protected]

1.4 Components
6
POWER cable (6P) * 1ea
(HPOWER0001)
AV cable * 1ea
(HAVCAB0002)
MODE cable * 1ea
(HARETC0001) RGB cable * 1ea
(HNAVIC0004)
CAN cable * 1ea
(HARETC0012)
OR
Keypad * 1ea
(SMTASY0063)
Ground cable * 1ea
(HGROUN0001)
IR cable (8P) * 1ea
(HIRCAB0003)
Remote control * 1ea
(REMOTE0001) FPC cable * 1ea
(SMTASY0075)
FFC cable (50P) * 1ea
(FFCABL0004)
Car-solutions.com
www.car-solutions.com
[email protected]

1.5 Exterior
7
①②③④⑤⑥
⑦⑧⑨
①DIP switch
②LED
③MODE
④RBG IN
⑤A/V(IN/OUT)
⑥POWER
⑦KEYPAD
⑧LCD IN/OUT
⑨CAN I/F
Dimension
Horizontal length 149mm
Vertical length 91mm
Height 19mm
Car-solutions.com
www.car-solutions.com
[email protected]

1.6 POWER cable
8
Blue
FMTX
I - DRV
GND
LAMP - RV
ACC
990mm
FILTER
& FUSE BOX
Orang
e Black
Red
Gray
Red
Gray
Orang
e
Black
Blue
990mm
Car-solutions.com
www.car-solutions.com
[email protected]

2.1 DIP switch
9
#PIN FUNCTION DIP S/W Selection
1 RGB INPUT MUTE ON : RGB Skip
OFF : RGB Display
2 A/V 1 MUTE ON : A/V 1 Skip
OFF : A/V1 Display
3 A/V 2 MUTE ON : A/V 2 Skip
OFF : A/V2 Display
4 A/V 3 MUTE ON : A/V 3 Skip
OFF : A/V3 Display
5 To select monitor size ON : 6.5” LCD Setting
OFF : 8.8” LCD Setting
6 N.C
7 Rear Mode ON : External Rear Camera
OFF : OEM Rear Camera
8 N.C
※ON : DOWN / OFF : UP
※Please make sure to disconnect the power cable of the interface and reconnect the power cable again to
apply the dip switch setting whenever changing DIP switch. Otherwise, DIP switch setting will not be applied.
Car-solutions.com
www.car-solutions.com
[email protected]

2.1 DIP switch
10
※DIP S/W Use Example
[BMW E65-6.5 Inch]
-. Use Input Mode : A/V3(DVD), Navigation (RGB)
-. Rear Camera : When to be installed on CVBS 4
▷DIP S/W : 1 OFF
▷DIP S/W : 2,3 ON (INPUT MODE SKIP)
▷DIP S/W : 4 OFF (enable A/V3)
▷DIP S/W : 5 ON (6.5 Inch)
▷DIP S/W : 6 OFF
▷DIP S/W : 7 ON (enable CVBS4)
▷DIP S/W : 8 OFF
[E65 8.8 Inch]
[E65 6.5 Inch]
#PIN
Type of monitor 5
E65 8.8” OFF
E65 6.5” ON
Car-solutions.com
www.car-solutions.com
[email protected]

2.2 Keypad usage
11
Select one between remote control and keypad
FACTORY MODE (Interface setting) :
Press these buttons on OSD keypad in the following sequence; UP→DOWN→UP →MENU
Key Function
MENU/EXIT Activate OSD menu and go back to the previous state after setting mode
SEL/INPUT Making a selection and changing modes
UP Moving leftward or upward
(If you press this button 2 seconds long, you can get access to HOT KEY function.)
DOWN Moving rightward or downward
(IF you press this button 2 seconds long, you can reset all data.)
Car-solutions.com
www.car-solutions.com
[email protected]

2.3 Remote control usage
12
Key Function
POWER & PIP Unavailable
MENU Activating OSD menu
OK Making a selection, changing image display
▲Moving upward
▼Moving downward
◀Moving leftward (If you press this button 2 seconds long, you can get access to
the factory mode.)
▶Moving rightward (If you press this button 2 seconds long, you can reset all the
data about user environment.)
Car-solutions.com
www.car-solutions.com
[email protected]

2.4 FACTORY mode
13
POSITION
- H-POSITION : moving in horizontal direction
- V-POSITION : moving in vertical direction
I-DRV
- To control DVD, Navi by I-DRV (Optional)
Refer to the “BMW Handle button NAVI setting” page.
REAR-CAM
- By Rear Wire : By using provided rear camera power cable , setting while rear camera installation
(same with previous version)
- By CAN-BUS : Setting for automatic display of rear camera after installed, (CAN wire connected)
FACTORY mode : Operated by pressing UP->DOWN->UP->MENU keys on the keypad in sequence or
Press ◀button 2 seconds long on the remote control.
Car-solutions.com
www.car-solutions.com
[email protected]

2.5 OSD (on screen display)
14
Analog RGB Mode
COLOR
-BRIGHTNESS
-CONTRAST
-RED
-GREEN
-BLUE
-COLOR BOX : Selecting one
among 3 color options
-SATURATION
-SHARPNESS
OPTION
-OSD H_POS
: Move of OSD window to Left, Right
-OSD V_POS
: Move of OSD window to Up, Down
- OSD TRANS
: OSD window transparency setting
- SCREEN MODE
: Screen Rate setting (4:3, 16:9)
- INITIAL : Initializing OSD setting
value
Video mode
Analog RGB Mode Video mode
Car-solutions.com
www.car-solutions.com
[email protected]

2.6 Parking guide line
15
①When the car is in reverse, press
‘UP’ key for 2 sec, the
guide line appears on the screen.
Factory Default : DISPLAY - DISABLE
②If you need to move the line
position, press ‘SEL’ key.
(Use ‘Up’, ‘Down’ Key of Keypad)
③On step no.2, press “SEL”
key once again, you can move
the line vertically by “UP”, “Down”
keys.
Car-solutions.com
www.car-solutions.com
[email protected]

2.7 BMW Handle Button NAVI setting
16
Oversea
Domestic
After implementing FACTORY MODE
(Interface setting), select I-DRV and press
the Sel button of Keypad, and then Navi
Setting window is displayed as shown right.
After selecting the one among RGB, AV1~3,
press the Sel button of keypad.
(It is fine to select any channel, because
the selecting of RGB, AV1~3 is useless. But,
the channel selected on this step will be
exempted on next channel selecting step.)
After the above steps finish, left picture
will appear. ARION, NET-770, ML-100S,
ML-740T are Domestic DTV model.
Select the model you want to use, then
select channel of RGB, AV1~3.
(The channel selected on the above
steps is exempted.)
NET-770 (DTV model) is designated AV1
as shown on the right picture.
※This function is not supported at domestic NAVI, but this setting is necessary for implementation of Domestic DTV.
※When DVD-IR (Black) wire of RGB-IN cable is connected to IR input wire of DTV, able to operate via handle buttons.
Car-solutions.com
www.car-solutions.com
[email protected]

3.1 Pre-installation Notices
17
During installation ignition key should be taken off and after all installation finish connect
power cable with interface for the last step.
Power cable should be separated when connecting interface.
Should be no any electronic devices or magnetic pole around installation place.
All steps of installation should be done by well-trained specialist.
Dismantling without manufacturer’s permission can not be guaranteed, (No permission to
break attached label on the board.)
Kindly check all parts are in the box, when receiving the product, if anything missing, inform to
the supplier or manufacturer.
According to our sales policy, any problems caused by user’s mistake, careless can not be
guaranteed.
Car-solutions.com
www.car-solutions.com
[email protected]

3.2 CAN Installation
18
E65 CAN Wiring Diagram
Green: CAN LOW
Orange: CAN HIGH
Car-solutions.com
www.car-solutions.com
[email protected]

3.3 Installation
19
1. Connect the FFC cable to FPC cable as
shown above. 2. Connect the FFC cable to the LCD-IN/OUT
connector of the board as shown above.
3. Connect the LVDS cable of head unit to
FPC cable as shown above. 4. Connect the FPC cable to the
connector of head unit as shown above.
Car-solutions.com
www.car-solutions.com
[email protected]

4. Troubleshooting
20
Q. I can not switch A/V sources
A. Check IR or Ground cable connection. Check LED lamps in the interface, if it is not on, check power cable.
Q. All I got on the screen is black.
A. Check second LED lamp of the interface is on, if not, check A/V sources connected are working well.
(Second lamp indicates AV sources connected works well.) Check interface connection has been done well.
Q. Displayed image color is not proper (too dim or not suitable color)
A. Try to select “INITIAL” in OSD menu, if it does not work, inform to manufacturer.)
Q. I can watch the rear camera on the screen
A. Set the DIP switch #7 as state “ON”.
Q. Unwanted A/V mode is displayed. (A/V source switching order : OEM->RGB->AV1->AV2->AV3)
A. Check DIP Switch Setting.
Q. OEM image is not displayed.
A. Check interface’s LCD In/Out cable connection. If the status keeps on, inform to manufacturer.
Q. Screen only displays white color.
A. Check LCD out cable is connected well, if this status keeps, inform to manufacturer.
Q. After setting PIP function, I got only half OEM image at the right in the screen.
A. This is not an error, just caused by user’s setting mistake, user should set to
“Split Screen” in the OEM menu.
Q. Rear CAM does not appear, when car is in reverse after CAN wiring.
A. Operate “FACTORY MODE” like left picture, then select “UTIL Rear Select”
If it is set as “LAMP”, change it to “CAN” by remote control or keypad.
※LAMP : In case of connecting “Rear-C” wire of Power Cable to Rear Lamp in vehicle.
CAN : In case of detecting Rear Cam thru CAN signal. (CAN must be wired)
Q. After moving gear to “P” or “D” from “Reverse”, I can’t get navigation, but half PDC Image in the screen.
A. Once, you starts driving, the screen displays navigation right away, this is not an system error.
Car-solutions.com
www.car-solutions.com
[email protected]