Car Solutions R04-MB14 User manual

R04-MB14 Rear View Camera Interface Release Date: 2015 - 06 -01
Button Function
★(Bookmark) Enter into the setting menu.
(Press the button 5 seconds)
Select( ) Select the setting menu and setting values.
BACK Back to previous menu.
Dial(▲, ▼, ◀, ▶)Move the menu-pointer and adjust the
setting values
BACK(Steering wheel) Change the mode to FVC(AV1),
when press the button 2 seconds.
1
LVDS Cable RVC Cable FVC(AV1) CableR04-MB14 POWER / CAN Cable
OFF
ON
Model Name R04-MB14
Latest Firmware Date 2015 -05 –24
Manual Version Rev. 1.7
Manual Release Date 2015 -06 -01
①Enter into the setting mode. ②Adjust guide lines position and ON / OFF ③Adjust PDC sensors position and ON / OFF ④Adjust values of brightness and contrast.
Components
Version Information
Setting mode
Setting mode
ON: ▼OFF: ▲
No.1 Rear View CAM ON(▼)/ OFF(▲)
No.2 Front View CAM ON(▼)/ OFF(▲)
No.3
Selection of
car model ON(▼)/ OFF(▲)
No.4
No.5
No.6
No.3 No.4 No.5 No.6 Car models
OFF(▲)ON(▼)OFF(▲)ON(▼)E, CLS / 7, 8-inch
OFF(▲)ON(▼) ON(▼) ON(▼)B, CLA / 8-inch
ON(▼)OFF(▲)OFF(▲)OFF(▲)B, CLA / 7-inch
OFF(▲)ON(▼)OFF(▲)OFF(▲)V-Class / 8.4-inch
OFF(▲)OFF(▲)ON(▼) ON(▼)V-Class / 7-inch
Dip Switch Settings
Car-solutions.com
www.car-solutions.com
[email protected]

COMAND NTG 5.0 Main Connector - CAN wires Inform
1
4
5
8
9
12
13
15
16
2
4
3
2
1
2
1CVBS IN
REAR CAMERA
REAR 12V OUT
GROUND
POWER / CAN
CAMERA IN
Rear-View Camera
Front-View Camera(or AVM)
LVDS OUT
DIP SWITCH
LVDS IN
8
7
6
5
4
3
2
1
MON CAN H
MON CAN L
PAS CAN H
PAS CAN L
BAT +
GROUND
REVERSE 12V IN
Pin # 12 = GND(Brown)
Pin # 15 = Battery POWER(Red)
Pin # 31 = PAS CAN LOW(Yellow)
Pin # 37 = PAS CAN HIGH(Yellow / White)
Pin # 32 = MON CAN LOW(Black)
Pin # 38 = MON CAN HIGH(Black / White)
*The wires color might be different depends on models.
You have to splice the CAN wires with each pins exactly.
*OEM CAN wires(High, Low) are twisted each other.
BAT+(Yellow)
REVERSE 12V IN(Orange)
(*Not necessary)
PAS CAN L(Green)
PAS CAN H(White)
GROUND(Black)
Monitor(OEM)
COMAND APS NTG 5.0 - Head Unit
(Blue ‘DISP port’)
(OEM LVDS Cable)
(Provided LVDS Cable)
17
23
22
28
29
35
34
40
※OEM LVDS connector should be connected to
‘LVDS OUT’ port.
Provided LVDS connector should be connected to
‘DISP port’ of Head unit instead to OEM connector.
Installation Diagram
(If reverse gear is not detected via CAN data,
connect the power(12V) of the backup light)
R04-MB14 Rear View Camera Interface
MON CAN L(Green)
MON CAN H(White)
31
37
32
38
Car-solutions.com
www.car-solutions.com
[email protected]