Car Solutions RGB-LE-V3 User manual

CONVERTER
USER MANUAL
RGB
[email protected]
car-solutions.com
car-solutions.com

INDEX
-. Pre-Caution
-. Main Specification
-. System Composition Map
-. Out-Line Dimension
-. MODULE EXTERNAL
-. Connector Pin Assignment
-
.DIPSWOperationProcess
.
DIP
SW
Operation
Process
-. Remote Control Guide
-. Products composition
-
FAQ
-
.
FAQ
[email protected]
car-solutions.com
car-solutions.com

-Pre-Caution
-You must keep the car key taken off from the car while you work this and finally,
connect power of the interface.
- When to connect the interface cable, you must keep the power cable taken off.
- You must work this at the environment without any static electricity or damages.
- All of process on this installation should be done by professionals.
- You must not break the labels attached on the board, if it’s broken, no warranty.
- When you receive this package you have to check whether there’s any parts not
included and you have to contact us right away.
Oiid bl db’fl l
-
O
ur repa
i
r serv
i
ce
d
o not accept any pro
bl
ems cause
d
b
y user
’
s any
f
au
l
t or care
l
essness.
[email protected]
car-solutions.com
car-solutions.com

-Main S
p
ecification
1. Input Spec. (MULTI VIDEO INTERFACE)
-. 2 x CVBS Input (External video source).
-. 1 x CVBS (REAR CAMERA) Input (Rear camera source)
-
1 x Analog RGB Input (Car commander original monitor output)
p
-
.
1
x
Analog
RGB
Input
(Car
commander
original
monitor
output)
-. 1 x Analog RGB Input (Navigation System output)-ÆOPTION
2. Output Spec.
-. 1 x CVBS OUTPUT (Video Out for installing Headrest monitor)
1RGBOUTPUT(LCDO i)
-.
1
x
RGB
OUTPUT(LCD
O
perat
i
on
)
-. 1 x Audio Select OUTPUT (For operating A/V sources – ex) 12V is come out on V1 port, when
AV1 is chosen.)
3. Power S
p
ec.
p
- Input Power : 8VDC ~ 24VDC
- Consumption Power : 5WATT, Max
4. Switch Input mode
-
NAVI/CVBS1 2 Original MUTE Function : Possible to mute each input by operating Dip S/W
-
NAVI/CVBS1
,
2
Original
MUTE
Function
:
Possible
to
mute
each
input
by
operating
Dip
S/W
- Possible to switch Input mode with remote control or toggle switch.
- Rear View Camera mode : When to sense rear gear power, be switched to Rear view camera
mode (Impossible to switch to rear mode with Toggle S/W or the
Remote control)
5. Special Function
- Remote Key scanning function (Option – If you want to use this function, you have to
purchase the remote additionally.)
* How to use?
Press 4291 buttons of Remote offered, then LED lamp of interface blinks. After that, press
any button of A/V source remote such as Navigation, DVD etc. that you want to use. If LED
lamp of the interface blinks slowly, It means to succeed and you can use the button that you
set for mode change.
[email protected]
car-solutions.com
car-solutions.com

-S
y
stem Com
p
osition Ma
p
Remote ControlSwitch for source toggle & REAR SENSE
yp p
NAVIGATION Input
(Analog RGB)
MCU
CAR Installation
OEM LCD
DISPLAY
CVBS1
VIDEO
CVBS2
CVBS
(Rear camera)
CIRCUIT VIDEO MUX
(CAR MAIN BOARD)
Car Screen Input POWER
CIRCUIT
CVBS OUT
HEADREST
MONITOR
Power Input
(+8VDC ~ +24VDC)
Dip S/W
[email protected]
car-solutions.com
car-solutions.com

-
Out
-
Line Dimension
Out
Line
Dimension
129mm * 75mm * 21mm
129mm
75mm
21
21
mm
※ This can change under manufacturer's circumstance
[email protected]
car-solutions.com
car-solutions.com

-Module External
RGB(OUT)
LED OEM(IN) DIP S/WAUDIO-SEL NAVI(IN)
V1IR
※ This can change under manufacturer's circumstance
MODEPOWER V2 R/V V-Out
[email protected]
car-solutions.com
car-solutions.com

-Module External
NAVI(IN) OEM(IN) RGB(OUT) DIP S/W ADO-SEL
P
OWER
M
ODE
IR
V1
V2
R/V
V
O
UT
P
OWER
M
ODE
IR
V1
V2
R/V
V
-
O
UT
※ This can change under manufacturer's circumstance
[email protected]
car-solutions.com
car-solutions.com

-Connector Pin Assi
g
nment
g
*NAVI-IN Connect *RGB-OEM Connect *RGB-OUT Connect
①②③④⑤⑥ ⑦
①
②
③
④
⑤
①②③④⑤⑥⑦⑧⑨⑩
① R DATA
② G DATA
③ B DATA
④
SYNC
① R Data : Red
② G Data : Green
①
②
③
④
⑤
①②③④⑤⑥⑦⑧⑨⑩
① B Data : Blue
② G Data : Green
③ R Data : Red
④
Sync Data : White
④
SYNC
⑤ GND
⑥ NAVI IR
⑦ DVD IR
④ Sync : White
⑤ GND : Black
④
Sync
Data
:
White
⑤GND : Black
⑥ ACC : Yellow
⑦ Video S/W : Orange
⑧
Not used
⑧
Not
used
※ This can change under manufacturer's circumstance
③ B Data : Blue
[email protected]
car-solutions.com
car-solutions.com

-Connector Pin Assi
g
nment
g
*Power Connect
⑥
⑤
⑥
④
①
(
③②①
①
GND
② I -Drive
③ F MTX
④N.C
⑤
ACC
⑤
⑥ R EAR
※ This can change under manufacturer's circumstance
[email protected]
car-solutions.com
car-solutions.com

-Connector Pin Assi
g
nment
* Power cable
g
FILTER
& FUSE BOX
I - DRV
GND
990
Orange
Black
Gray
ACC
990
mm
Red
Gray
Red
Orange
LAMP - RV
990mm
Gray
Black
[email protected]
car-solutions.com
car-solutions.com

-
DIP SW Operation Process
DIP
SW
Operation
Process
※ ON : DOWN, OFF : UP ※DIP S/W Use Example
#PIN FUNCTION DIP S/W Selection
1 RGB INPUT MUTE ON : Skipping RGB Mode
OFF : RGB Display
[W211]
-. Use Input Mode : CVBS1, Navigation (RGB), Main
-. Rear Camera : When to be installed on CVBS 4
2CVBS1 MUTE
ON : Skipping CVBS1
OFF : CVBS1 Display
3CVBS2 MUTE
ON : Skipping CVBS2
OFF : CVBS2 Dis
p
la
y
▷ DIP S/W : 1 ÆOFF
▷ DIP S/W : 2 ÆOFF
▷ DIP S/W : 3 ÆON
▷ DIP S/W : 4 ÆOFF (All of the Car except Cayenne)
▷
DIP S/W : 5
Æ
OFF
py
4CAN
ON : When install to the Cayenne
OFF : When install to all of the car
5
OEM MUTE
ON : Skipping OEM
▷
DIP
S/W
:
5
Æ
OFF
▷ DIP S/W : 6 ÆOFF
▷ DIP S/W : 7 ÆON (enable CVBS4)
▷ DIP S/W : 8 ÆOFF
5
OEM
MUTE
OFF : OEM Dis
p
lay
6INTERLACE
ON : Non-Interlace
OFF : Interlace
ON : External Rear Camera
7REAR MODE
ON
:
External
Rear
Camera
OFF : OEM Rear Camera
8 SYNC ON GREEN ON : Sync On Green (RGSB)
OFF : Sync On Green Off
* Caution
- If the displayed screen vibrates, please try to
operate Dip S/W No. 6 after turning power off.
[email protected]
car-solutions.com
car-solutions.com

-
Remote Control Guide
Remote
Control
Guide
Power : Mode is changed on only headrest monitor by this button, when front
monitor shows Navigation or Rearview camera, Main.
Source : When to change mode, you can change mode by this button.
Navi : To change mode to Navigation directly
AV1 : To change mode to A/V source you connected to A/V1 directly
AV2 : To change mode to A/V source you connected to A/V2 directly
AV3 : To change mode to A/V source you connected to A/V3 directly
▲ : Increasing
OK : Select
▼ : Decreasing
Menu : To enable OSD Menu
4:3 : To convert screen rate from 4:3 to 16:9 or 16:9 to 4:3
Main : To change to Main mode directly
Scan : Not available
Mute : Not available
Disp : Currency A/V source screen display
Reset : To make all value to factory default.
Cont. : To adjust Color under OSD (Hot Key)
Brt. : To adjust Brightness under OSD (Hot Key)
[email protected]
car-solutions.com
car-solutions.com

-
Products composition
Products
composition
Power cable : 1
Mode cable : 1
RGB(Out) cable : 1
RGB OEM 1
Audio Select Cable: 1
RGB NAVI : 1
IR Cable : 1
RtCtl
1
RGB
OEM
:
1
R
emo
t
e
C
on
t
ro
l
:
1
[email protected]
car-solutions.com
car-solutions.com

V
Installation Structure
B
G
R
S
Y
N
C
G
N
D
A
C
C
V
i
d
e
o
S
/
W
N
.
C
R
G
B
S
y
n
G
N
D
R
G
B
S
y
n
G
N
D
MONITOR
O
O
B
G
R
C
D
C
W
C
R
G
B
c
D
R
G
B
c
D
Offered
FFC
O
U
T
P
U
T
1
O
U
T
P
U
T
2
LED NAVI(IN) DIP S/WADO-SEL RGB(OUT) OEM(IN)
Original
FFC
RGB CONVERTER(LE)
Control Box
POWER MODE IR V1 V2 R/V V-OUT
ACC
Control
Box
X
LAMP-
RV
FMTX
GND
I-DRV
Solder this wire to the Head
Unit for changing mode by
original button
(Only for Cayenne, W164EU,
W211)
[email protected]
car-solutions.com
car-solutions.com

-
FAQ
FAQ
1. When can not change mode.
-. Check if the IR Cable (remote control) is connected or not.
-. Check if LED is turned on or not. If it is not turned on
,
Check if
p
ower cable is connected or not.
,p
2. When the screen is displaying only black color.
-. Check if 2nd LED is turned on or not. If it is not turned on, please check the sources that you will connect with the
interface is operating well or not.
-. Check if interface is connected well.
3. When displayed color of screen is not proper. (If it’s too dark or the color is not proper)
-. Try to push “Reset button” on the remote control. If the color of screen keeps on displaying wrong color, you have
to ask manufacturer for the problem.
4Wh B k
itdildth
4
.
Wh
en
B
ac
k
-up camera
i
s no
t
di
sp
l
aye
d
on
th
e screen.
-. Turn Dip S/W no.7 on.
5. When the mode you set is not skip.
-. Check if Dip S/W is set in proper way.
6. When Main screen on the car is not displayed.
-. Check if In/Out cables are connected well. If it keeps showing the same problem, you have to
ask manufacturer for the problem.
7 When the screen is displaying only white color
7
.
When
the
screen
is
displaying
only
white
color
.
-. Check if out cable is connected well. If it keeps showing the same problem, you have to ask
manufacturer for the problem.
8. The case the screen is changed to Main mode despite of choosing Back-up camera mode.
-
Check if Dip S/W no 7 is turned on If it
’
snot youhavetoturniton
.
Check
if
Dip
S/W
no
.
7
is
turned
on
.
If
it s
not
,
you
have
to
turn
it
on
.
9. When the screen is blinking or not proper.
-. Turn Dip S/W no.6 on.
[email protected]
car-solutions.com
car-solutions.com