CareCo Tuni Bossa User guide

Bossa
Rollator
OWNERS HANDBOOK
Product Code: WA01062

Your Tuni Bossa Rollator
1. The Tuni Bossa Rollator folds to a compact
size for easy storage.
2. Height-adjustable handles for the user’s
safety and comfort are included.
3. Swivel front wheels offer easy control.
4. The curb climber design manoeuvres easily
over obstructions.
5. There is a brake system for parking
and stopping.
Product Features

Thank you for purchasing the Tuni Bossa Rollator.
The Bossa Rollator has been designed and
manufactured to meet our own high level of
specifications and we hope you will be delighted
with your purchase.
The Bossa Rollator is a lightweight and portable
rollator designed to aid the user to walk and offer
stability and security. The Bossa is designed for
use indoors and outdoors and will take a
maximum user weight of 136kg.
NOTE: Check all parts for shipping damage. In
case of shipping damage, DO NOT use – contact
the dealer/carrier for further instruction.
Rollator Dimensions: 67.5cm (Length) x
66.5cm (Width) x 81.5 - 95.5cm (Height)
Seat Dimensions: 22cm (Depth) x 47.5cm
(Width)
Folded Dimensions: 67.5cm (Length) x
26.5cm (Width) x 82.5cm (Height)
Brake Method: Handle Brake
Max User Weight: 136kg
Introduction
Specification

Ensure rollator is level to the ground before
using. All screws must be tightened, ensuring
there is no movement.
DO NOT hang anything on either side frame. This
will: (A) cause side tube to bend, and make the
rollator unstable, and/or (B) cause rollator to tip,
resulting in injury or damage.
NOTE: Before using, test rollator by grasping the
side frames and, with some force, attempt to fold
them inward. The rollator will remain locked in
the OPEN position if it is engaged properly.
To open the rollator, swing the side frames
outward. Lower the seat, pushing down until
the plastic slot under the seat support is
properly locked into the screw on the lever of
cross tube, and seat support is fully fixed on the
plastic slot of side brace as in figure 1:
To fold the rollator, grasp the handle. Fold the
rollator inwards by lifting the seat supports or
pulling the middle of the seat cloth as shown in
figure 2:
Read Before Use
Opening / Folding
Figure 1 Figure 2

The rollator height should be adjusted so that
when the user’s arm is down by their side, the
hand grip is at wrist height. This will ensure the
arms are at an approximate 20°-30° bend when
using the rollator.
To adjust the height, release the quick release
lever and adjust the handrails upward or
downward to the desired height. Ensure the
quick release lever is fastened again once the
correct position is found as in figure 3:
To adjust the backrest, loosen the knob
attached to the backrest fabric, as shown in
figure 4:
Figure 3 Figure 4
Quick Release Lever Knob
Pull the top of the brake handles up towards the
hand grips to activate the hand brake.
To remain stationary, continue to hold the brake
handles up.
Using the Hand Brake
Adjusting the Height of the Rollator

To continue mobility, release the brake handles.
To lock the hand brake, push down on the
bottom portion of the brake handle as shown in
figure 5 until an audible
“click” is heard. To
release pull up on the
top part of the brake
handle as in figure 5:
Figure 5
Figure 6
Test the brake. If the tension of the brake
handle is too loose/tight, perform the following
as shown in figure 6:
1. Loosen the Phillips screw on the brake
clamp.
2. Pull the brake wire further through the brake
clamp.
Note: There will be additional excess wire. It may
be necessary to fold wire up to keep wire from
interfering with brake action.
Repeat this process for the other brake.
Cable Adjuster Unit

To ensure the safe operation of the rollator,
these instructions MUST be followed:
DO NOT install or use this equipment before
reading and understanding this instruction
sheet. Please keep this manual properly for
future reference. If you are unable to under-
stand the warnings, cautions or instructions,
contact a healthcare professional, dealer or
technical personnel before attempting to install
this equipment – otherwise, injury or damage
may occur.
Each individual should consult with their
physician or therapist to determine proper
adjustment and usage.
Rollators are NOT intended to be self-propelled
while seated. DO NOT use the rollator on the
stairs or on elevators/escalators, please be
careful when using on slope.
It is recommended that a physical/occupational
therapist should assist in the height adjustment
of the rollator for maximum support and correct
brake activation, the fixture of the screw, the
position of the quick release/assembly kits.
Always ensure screws are fastened to the
connector, so that the connector cannot move
when forced. Ensure all copper balls fully
protrude through adjustment holes.
Safety Summary

Failure to follow these warnings can result in
personal injury. Care should be taken to ensure
that ALL hand and height adjustment are secure
and that moving parts are in good working
order before using this or any mobility aid. In
the process of using, all wheels must always be
in contact with the ground. This will ensure the
rollator is properly balanced. Before using the
seat, the brake must be in the locking position.
When using a rollator in the stationary state,
the hand brake must be locked.
After unfolding or assembling the rollator,
ensure that the seat support tube is securely
locked in the side slot and the quick release/
assembly kits are in their correct position and
locked. Ensure rollator is level to the ground
before using. All screws must be tightened,
ensuring there is no movement.
DO NOT hang anything on either side frame.
This will: (A) cause the side tube to bend, and
make the rollator mechanical unstable, and/or
(B) cause the rollator to tip, resulting in injury or
damage.
Always test to see that the rollator and
attachments are properly and securely locked in
place before using.

• Clean wheels with warm water and
detergent, dry wheels with a clean cloth.
If wheels squeak, please add 3-in-1
lubricating oil regularly.
• Ensure that every part of the rollator is
secure at ALL times.
• Check all screws regularly and make sure
the seat tubes are fixed into the side slot
properly - if not, press it again to secure.
• Ensure the quick release wheels are
assembled correctly.
• Ensure the metal buttons are protruding
from the handle tube.
• Replace any broken, damaged or worn
parts immediately.
• Wash the bag with water or gentle
detergent.
Care and Maintenance
Your Tuni branded product is under warranty
to be free from defects in material and
workmanship for one year from date of receipt.
The warranty does not extend to non-durable
parts, such as rubber accessories, castors and
grips, which are subject to normal wear and tear
and require periodic replacement.
If you have any queries please contact your
supplier
The manufacturer reserves the right to alter without notice any weights, measurements
or other technical data shown in this manual. All figures, measurements and capacities
shown in this manual are approximate and do not constitute specifications.
Warranty