Carefree FREEDOM FREESTYLE WM User manual

052573-001r11 Printed in USA July, 2017
I NSTALLATION M ANUAL
FREEDOM FREESTYLE WM
12VMOTORIZED LATERAL ARM BOX AWNING W/DIRECT RESPONSE
RV
Read this manual before installing or using this product. Failure to follow the instructions
and safety precautions in this manual can result in personal injury and/or cause the
product to not operate properly.
TABLE OF CONTENTS
Product Overview.......................................................................................................................... 1
Component Check list.............................................................................................................................2
Installation .....................................................................................................................................3
Attaching the Mounting Plates................................................................................................................3
Mounting the Awning..............................................................................................................................4
Securing the Awning...............................................................................................................................5
Jumping the Motor..........................................................................................................................5
Switch Installation......................................................................................................................... 6
Optional LED Lighting...................................................................................................................8
Switch Installation...................................................................................................................................8
Pitch Adjustment...........................................................................................................................9
Manual Override ............................................................................................................................9
Setting the Motor Limits .............................................................................................................10
Out Limit Switch ...........................................................................................................................10
IN Limit Switch..............................................................................................................................10

PROPRIETARY STATEMENT
The Freedom Freestyle WM Awning is a product of Carefree of Colorado, located in Broomfield, Colorado,
USA. The information contained in or disclosed in this document is considered proprietary to Carefree of
Colorado. Every effort has been made to ensure that the information presented in the document is
accurate and complete. However, Carefree of Colorado assumes no liability for errors or for any damages
that result from the use of this document.
The information contained in this manual pertains to the current configuration of the models listed on the
title page. Earlier model configurations may differ from the information given. Carefree of Colorado
reserves the right to cancel, change, alter or add any parts and assemblies, described in this manual,
without prior notice.
Carefree of Colorado agrees to allow the reproduction of this document for use with Carefree of Colorado
products only. Any other reproduction or translation of this document in whole or part is strictly prohibited
without prior written approval from Carefree of Colorado.
SAFETY INFORMATION
This is the safety alert symbol. It is used to alert individuals to potential
personal injury hazards. Obey all safety messages that follow this symbol to
avoid possible personal injury or death.
WARNING Indicates a hazardous situation, which if not avoided, could result in death or
serious bodily injury.
CAUTION Indicates a hazardous situation, which if not avoided, may result in minor or
moderate bodily injury.
NOTICE Indicates a situation that may result in equipment-related damage.
General Safety:
WARNING Shock Hazard. Always disconnect battery or power source before
working on or around the electrical system.
WARNING Always wear appropriate safety equipment (i.e. goggles).
CAUTION Always use appropriate lifting devices and/or helpers when lifting or
holding heavy objects.
NOTICE When using fasteners, do not over tighten. Soft materials such as fiberglass and
aluminum can be "stripped out" and lose the ability to grip and hold.
CALIFORNIA PROPOSITION 65
WARNING This product contains chemicals known to the state of California to cause
cancer or birth defects or other reproductive harm. California’s Proposition 65 requires this
warning to be given to customers in the state of California.
Reference Publications located at www.carefreeofcolorado.com:
052573-001 Installation Manual
052573-201 Owner's Manual
Carefree of Colorado 2145 W. 6
th
Avenue Broomfield, CO 80020 a Scott Fetzer company

Carefree Installation Manual FREEDOM FREESTYLE WM
052573-001r11 1
PRODUCT OVERVIEW
The Freedom Freestyle WM Awning is a state of the art lateral arm awning. When retracted, the housing
provides protection against the elements while the streamlined styling blends in with the coach sidewall.
The full tension canopy fabric allows the awning to be partially or fully extended for best shade coverage.
Each unit is equipped with lateral support arms. No vertical arms interfere with coach sidewalls, custom
graphics or equipment that may be mounted on the sidewalls.
Freedom Awning Specifications:
Fully retractable and self storing;
The sealed awning motor operates on standard 12VDC (range 10VDC to 14VDC);
Case and frame are constructed of high-strength aluminum extrusions, protected with a polyester paint finish;
Stainless steel fasteners and hardware.
Direct Response is standard.
SPECIFICATIONS
wm001a
Awning Width
Fabric Width
3.8"
[9.7cm]
5.8"
[14.8cm]
4.25"
[10.8cm]
2.25"
[5.7cm]
LENGTHS: meters 3.0 3.5 4 4.5 5.0
feet 9.8 11.5 13 14.75 16.4
EXTENSION: 250cm [98"]
LEAD RAIL SUPPORT: 4m or less: 2 Lateral Spring Arms; 4.5 & 5m 3 Lateral Spring Arms
POSITION CONTROL: 12V Motorized w/ tubular motor
12V Direct Response - Standard
MOTOR SPECIFICATIONS
Motor Type: Tubular
Power: 12VDC Minimum: 10VDC Output: 30 Watts
Nominal Current: 2.5Amps Max Current: 14Amps (stall @ min voltage)
Torque Continuous: 6Nm/4.5 ft-lbs. Tightening: 18Nm/13.2 ft-lbs.
Speed 24 rpm
COLORS AVAILABLE
Case Satin, White or Black
Fabric:
1
Vinyl

FREEDOM FREESTYLE WM Installation Manual Carefree of Colorado
2 052573-001r11
COMPONENT CHECK LIST
RETRACT
ON
EXTEND
Awning Control
OFF
9
10 131211
6 7
4
FF006
8
2
1
53
ITEM DESCRIPTION QTY NOTE
1 Awning Assembly 1 1
2 Mounting Plate 40cm NOTE 2
3 Screw, Self Drilling #10 x 5/8" NOTE 3
4 Screw, Self Drilling #10 x 1" NOTE 3
5 Screw, Self Drilling, Hex Head #6 x 3/8" NOTE 3
6 Bolt thru hardware M6 x 60mm NOTE 4,6
7 Lag screw 1/4" x 1.5" 6 5,6
8 Screw, Thread Cutting 1/4-20 x 3/4" 6 5,6
9 Switch Kit 1
10 Terminal, Female, .187 18-22 awg 3
11 Terminal, Female, .187 14-16 awg 2
12 Terminal, Female, .25 14-16 awg 1
13 Terminal, Male, .25 14-16 awg 1
NOTES: 1. Product configuration is specified at time of order, including length, fabric, color etc. Check
assembly against original purchase order.
2. 4 meter and less uses a quantity of 3 plates; 4.5m and 5m uses a quantity of 4.
3. Screw (item 3) quantity is 2 per mounting plate. Screw (item 4) quantity is 1 per mounting plate.
Screw (item 5) is quantity 2 per mounting plate (reference note 2). Screws are included with
mounting plates.
4. Bolt thru hardware (item 6) includes M6 x 60 carriage bolt, fender washer, nylock nut and bolt
cover. Quantity is 6 each per mounting plate (reference note 2).
5. Quantities included in screw pack for items 7 and 8 are for one mounting plate only.
6. Screw packs include items 6 thru 8. Packs are ordered separately.

Carefree Installation Manual FREEDOM FREESTYLE WM
052573-001r11 3
INSTALLATION
For structural and operation integrity, the Freedom Freestyle WM awning must be mounted with the
included mounting plates and cannot be mounted using an awning rail.
Prior to mounting the awning, ensure that the awning will not interfere with light fixtures, exhaust vents,
openings, etc.
ATTACHING THE MOUNTING PLATES
1. Determine the optimum positioning of the awning.
1. The centerline of the awning fabric is offset from the centerline of the awning assembly. To align
the center of the fabric, use the backplate of the awning assembly for measurements.
2. The bottom of the mounting plates should be 28cm [11"] above any openings or frames to avoid
interference when the awning is installed.
NOTE: Height is based on clearance over a 76cm [30"] door extension. The mounting height will
vary 1.9cm [.75"] for every 5cm [2"] change in extension. For longer door extensions, add the
calculated difference. For shorter extensions, subtract the difference.
Dimensions are based on the steepest pitch. The height can be reduced by reducing the pitch.
3. Measure each end of the awning position from the ground so that the awning is mounted parallel to the
ground.
FF004
5.0m
Edge of Back Plate Edge of Back Plate
155cm [61”] 155cm [61”]
132cm [52”] 132cm [52”]
4.5m
1.25cm [.5”]
14cm [5.5”]
1.25cm [.5”]
14cm [5.5”]
1.25cm [.5”]
Edge of Back Plate Edge of Back Plate
Center of Back Plate
9cm [3.5”] 4.5cm [1.75”]
Awning Length
3.0m
3.5m
4.0m
1.25cm [.5”]
14cm [5.5”]
38.5cm [15.5”]
14cm [5.5”]
38.5cm [15.5”]
9cm [3.5”] 4.5cm [1.75”]
Awning Length
M6 x 60mm Carriage Bolt
8mm [5/16”] Hole
Nylock Nut
Mounting Plate Mounting Plate
1/4” x 1.5” Lag Screw or
1/4” x 3/4” Thread Cutting Screws
Pilot Hole
5/32” (Lag Screw)
or
7/32” (Thread Cutting Screw)
Fender Washer
Bolt Cover
40cm [15.75”] (typ)
40cm [15.75”] (typ)
14.8cm
[5.8”]
14.8cm
[5.8”]
4. Mark the position with a chalk line.
5. Determine the correct plate pattern then use the plates as a template.
NOTE: The brackets can be mounted using the bolt through hardware or with lag screws or thread cutting
screws.

FREEDOM FREESTYLE WM Installation Manual Carefree of Colorado
4 052573-001r11
6. For bolt through:
6.1. Using the plates as a template, drill 8mm [5/16"] holes through the vehicle wall to match the plates.
6.2. Attach the plates using M6 x 60mm carriage bolts, fender washers, nylock nuts and bolt covers (6
per plate).
7. For lag screws or thread cutting screws:
Two optional screw types are furnished. The lag screws can be used for mounting into wood or
aluminum frames. The thread cutter screws can be used when attaching into steel plate.
7.1. Using the plates as a template, drill 5/32" pilot holes for lag screws or 7/32" pilot holes for the
thread cutter screws. Use care to not drill through the wall.
7.2. Attach the plates (6 per plate).
8. Use the dimensions shown to locate the routing hole
for the motor cable..
NOTES: The hole location can be located in the areas
shown to avoid interior framing, cabinets and electrical
components that could be damaged or interfere with
the hole location.
Ensure that the awning cable is accessible after routing.
The cable extends from the awning 72" - 89" depending on the awning configuration. If the final routing to the
switch location is greater than the supplied wire, the installer must splice additional wire to the awning cable.
Ensure that the new wire matches the gauge of the existing wire.
Wire and splices must be furnished by the installer.
This is a preliminary step, the wire and switch installation are completed after the awning is mounted.
9. Drill an 5/16" [8mm] hole through the outer vehicle wall.
MOUNTING THE AWNING
1. Set the awning into the hooks of the
mounting plates.
Route the awning cable through the
hole drilled previously while lifting the
awning into position.
Tip: If the wire is routed along the
back of the case, use small pieces of
tape to hold the wire in place while
lifting the awning.
2. Adjust the position of the awning
horizontally as required.
3. Firmly hold the awning in the brackets and attach the awning case to the brackets using two (2) #6 x
3/8" screws through the bottom of the bracket into the awning case.
FF005
Back Plate
Mounting Plate
Route Motor Cable
through Groove in
Back Plate
#6 x 3/8” Screw
(2 per Bracket)
Edge of Back Plate
16mm [5/8”] 5mm [3/16”] (min.)
8mm
[5/16”]
Hole thru Wall
Locate hole in these areas
FF007

Carefree Installation Manual FREEDOM FREESTYLE WM
052573-001r11 5
SECURING THE AWNING
The awning must be secured as described below. This step can be done after the wiring is completed and
the awning can be opened using the switch or the awning can be opened using the procedure below
"Jumping the Motor".
NOTICE For proper awning operation and structural integrity, the awning must be secured as
described. Failure to secure the awning may result in damage to the awning and vehicle and void the
warranty.
1. Open the awning.
2. Through the flat plate of each case knuckle, use two (3)
#10 x 5/8" self-drilling screws and one (1) #10 x 1" self-
drilling screw to attach the awning to the mounting
brackets.
NOTE: For 4 meter and smaller awnings, there are two (2)
arm case knuckles. For 4.5 and 5 meter awnings there are
three (3) arm case knuckles.
Jumping the Motor
If it is necessary to open the awning before the switch
and wiring are complete, it is possible to jump the motor
to open the awning.
1. Separate the wires at the end of the harness cable.
2. Attach the
RED wire to the positive terminal of a 12-
14V battery.
3. Attach the
BLACK wire to the negative terminal of the
battery.
NOTE: The awning circuitry includes "Reverse Polarity Protection" if the battery connections are
accidently reversed the awning electronics will not be damaged. If the wires are reversed, remove from
the battery and reconnect in the correct order.
4. To extend the awning: Short and hold the BROWN and YELLOW wires together until the awning is open.
5. To retract the awning: Momentarily connect the GRAY and YELLOW wires together until the awning is
closed.
Red
Black
Yellow
Brown
Gray
Battery
Short the
Brown & Yellow Wires
to Extend the Awning
Momentarily Connect the
Gray & Yellow Wires
to Retract the Awning
FF012
A
rm Case Knuckle FF011
#10 x 5/8
Self Drilling Screw (x2)
#10 x 1
Self Drilling Screw

FREEDOM FREESTYLE WM Installation Manual Carefree of Colorado
6 052573-001r11
SWITCH INSTALLATION
WARNING Shock Hazard. Always disconnect battery or power source before
working on or around the electrical system.
NOTICE To comply with 2015 NFPA 1192 RV Standard, Section 6.4.9, Switches must be
mounted as follows:
a) Installed in a dedicated switch cabinet with a latching door; or,
b) Installed with the optional covered bezel available from Carefree; or,
c) Installed in a cabinet with a latching door where the switch is protected and CANNOT be
activated by any items or cargo that may move or shift during transit; or,
d) Installed with an interrupt circuit that disables awning extension when the vehicle is in motion (i.e.
a relay tied into the parking brake or ignition that disconnects the BROWN extend wire).
1. Determine the location for the switch.
1.1. There is 70" [180cm] of wire from the motor location. If the final routing to the switch location is
greater than supplied cable, the installer must splice wire extensions to the cable wires.
1.1.1. For the motor wires use 16awg wire
1.1.2. For the switch wires use 20awg wire.
1.1.3. Wire and splices are furnished by the installer.
1.2. Location should provide the operator a view of the awning during operation.
2. At the switch location cut a 2-5/16" [5.9cm) x 1-1/2" [3.8cm] hole.
3. Route the cable from the awning through the hole.
4. Terminate the three (3) 22awg wires (Brown,
Yellow, Gray) with .187, 18-20 awg female
terminals. Attach to the EXTEND/RETRACT switch as
shown in the wiring diagram.
5. Terminate the RED wire from the cable with a .187,
14-16 awg female terminal. Attach to one terminal
of the ON/OFF switch.
6. Terminate the BLACK wire from the cable with a .25,
14-16 awg male terminal.
7. Run a minimum 14 awg wire to chassis ground.
Suitable ground would be the vehicle chassis or
conductive structure connected to the chassis.
Terminate the wire with .25, 14-16 awg female
terminal.
8. Connect the ground wire to the black wire from the cable.
9. Run a minimum 14 awg wire from the power distribution panel (auxiliary battery circuit) or equivalent. The
circuit should be protected by a 15-amp fuse. Terminate the wire with a .187, 14-16 awg female terminal.
Attach to one terminal of the ON/OFF switch.
NOTE: If the wire run is 30 feet or longer, use 12awg wire to prevent voltage drop. Use the
appropriate wire terminals for the wire size.
10. Push the wires and switches into the hole then attach the switch frame using 4 #6 x 1/2" screws.
11. Snap the switch bezel over the switch frame.
1" [2.5cm]
LCDR004
2.32" [5.9cm]
1.5"
[3.8cm]
#6 x 1/2" Screw (x4)
RETRACT
ON
EXTEND
OFF
Awning Control
RETRACT
ON
EXTEND
Awning Control
OFF
Optional
Covered Bezel

Carefree Installation Manual FREEDOM FREESTYLE WM
052573-001r11 7
FF001a
On/Off
Rear View of
Switch Assy
Control Module
(mounted in
lead rail)
Gray
Yellow
Brown
Red
Black
Red
Black
Awning
Brown
Blue
(Retract)
(Common)
(Extend)
(+12Vdc)
(Ground)
MF
MF
FM
FM
MF
MF
MF
F
M
Chassis Ground
.25, 14-16awg
Spade Terminals
1 Male, 1 Female
+12VDC .187, 14-16awg
Female Spade
Terminals (x2)
.187, 18-20awg
Female Spade
Terminals (x3)
Additional
Extend/Retract
Switch
Gray
Yellow
Brown
Extend/
Retract
M
F
M
F
Blue
Brown
Red Shrinkwrap
Black Shrinkwrap
Red
18awg Wire
(minimum)
LED Strip in Lead Rail
2A In-line Fuse
Red
Black
+12VDC
Chassis Ground Module Harness (Routed on Top of Arm)
(+12Vdc)
(Ground)
LED Switch
See Below
Red
+12VDC
Single Pole, Single Throw Switch
18awg Wire
(minimum)
Red (from power harness)
18-24awg
Female Disconnect (x2)
2A In-line Fuse GND
Red
+12VDC
Lighted Single Throw Switch
18awg Wire
(minimum)
Red (from power harness)
2A In-line Fuse
18-24awg
Female Disconnect (x2)

FREEDOM FREESTYLE WM Installation Manual Carefree of Colorado
8 052573-001r11
OPTIONAL LED LIGHTING
Optional LED lighting may be mounted in the lead rail. The wiring runs along the top of the arm.
The LED wire harness is incorporated as part of the sensor harness.
NOTICE The following information must be followed to avoid damage to the wiring during and
after installation.
a) The wire should be secured to the wall of the vehicle where it is exposed on the outside of the
vehicle. Use a quality silicone sealant/adhesive.
b) Do not route the wire over sharp edges or heat sources that can damage the wires or wire
insulation.
c) Damage that is a result of improper routing may void warranty.
SWITCH INSTALLATION
NOTE: Installers may choose to furnish the control switch. The installation requires that the power line
(+12VDC) be attached to a dedicated 2A circuit breaker or a 2A in-line fuse must be installed between the
switch and power source. For easy access, locate the fuse close to the switch.
LED020
LED Strip
Vehicle Wall
Red
+12VDC
GND
Switch
18awg Wire
(minimum)
Red Black
2A In-line Fuse
See Switch Detail
ON
OFF
2A In-line Fuse
(+12VDC Line)
Red
+12VDC
Single Pole, Single Throw Switch
18awg Wire
(minimum)
Red (from power harness)
18-24awg
Female Disconnect (x2)
2A In-line Fuse
GND
Red
+12VDC
Lighted Single Throw Switch
18awg Wire
(minimum)
Red (from power harness)
2A In-line Fuse
18-24awg
Female Disconnect (x2)
1.13"
1.5"
#6 x 1/2" Screw (x2)
1. Determine the location of the switch.
2. At the switch location, cut a 1 1/8" x 1 1/2" hole.
3. Wire the switch as shown below. Wire terminals at the switch are .187, 18-24 awg female disconnects.
NOTE: Allow adequate slack in the 12VDC power line so that the in-line fuse (installed in step 4) can be
accessed from behind the switch.
4. Install the in-line fuse:
4.1. Near the switch, cut the red 12VDC power line to the switch. Do not strip the insulation.
4.2. Insert a wire end into one of the wire channels until it butts up against the stop.
4.3. Fold that half of the connector body over until the element contacts the wire. Use pliers to crimp
the connector closed.
4.4. Repeat for the second wire end.
4.5. Slide the fuse into the fuse port. Ensure that is firmly seated.
5. Press the in-line fuse, wires and switch into the mounting hole. Secure the switch using two (2) #6 x
1/2" screws.
6. Snap the switch bezel over the switch frame.

Carefree Installation Manual FREEDOM FREESTYLE WM
052573-001r11 9
PITCH ADJUSTMENT
The pitch for Freedom Freestyle WM can be adjusted to optimize the installation.
1. Open the awning to access the adjustment screws
located on the arm case knuckles.
2. Have a second person lift up on the lead rail to relieve the
pressure on the adjustment screws.
3. Using a 4mm allen wrench, loosen the top screw. Turn the
bottom adjustment screw clockwise to raise the lead rail; turn
the adjustment screw counterclockwise to lower the lead rail.
4. When the pitch is set at the desired angle, tighten the top screw.
5. Repeat for each arm. Ensure that the lead rail is parallel with the awning case.
NOTE: The Freedom Freestyle AM lead rail self-adjusts to accommodate the pitch. No adjustment is
required to the lead rail when the pitch is adjusted.
MANUAL OVERRIDE
If power to the vehicle is not available, the awning can be safely retracted
using the manual override located on the idler (right) end of the case.
NOTE: This procedure cannot be used to extend the awning.
1. Remove the plug from the right endcap and save.
2. Insert a 3/8" socket drive extension and handle into the square drive
hole inside the endcap.
3. Turn the handle counterclockwise until the awning is retracted.
4. Replace the plug.
NOTICE After closing the awning with the manual override, the lead rail may move out from the case 1/4" -
1/2". This is normal and the awning is secure for travel until power is restored or repairs are completed. Do not
attempt to force the lead rail in with the override, serious damage can occur to the awning.
Remove Plug
3/8” Socket
Drive Extension
WM012
Pitch Adjustment Screw
Raise
Lower
Loosen Top Screw when Adjusting
Tighten When Finished
FF030

FREEDOM FREESTYLE WM Installation Manual Carefree of Colorado
10 052573-001r11
SETTING THE MOTOR
LIMITS
The motor limit switches are preset
at the factory for best operation of
the awning. The “OUT” limit switch
is used to stop the motor when the
awning is fully extended. The “IN”
limit switch is used to stop the motor
when the awning is fully retracted.
The limit switches are located inside
the motor endcap.
To access the switches, remove the outer motor endcap and plug.
Out Limit Switch
1. Extend the awning out completely.
2. Confirm that the arms are fully extended. The motor should stop and the fabric should be tight. If the
motor continues to run, the fabric will sag; or, if the motor quits before the arms are fully extended, it will
be necessary to adjust the “OUT” limit switch.
NOTE: It is best to make the adjustments in increments of a single turn. 3 full turns of the screw
equals approximately 2” of fabric extension.
3. If the fabric sags:
3.1. Retract the awning until the fabric is tight then retract an addition 10"-12".
3.2. Using a 4mm Allen wrench turn the “OUT” limit switch COUNTERCLOCKWISE to reduce the time the
motor runs.
3.3. Extend to confirm that the adjustment is correct.
3.4. Repeat the procedure until the awning extends correctly.
4. If the arms do not extend completely:
4.1. Retract the awning approximately 10"-12".
4.2.Using a 4mm Allen wrench turn the “OUT” limit switch CLOCKWISE to increase the time the motor runs.
4.3. Extend to confirm that the adjustment is correct.
4.4. Repeat the procedure until the awning extends correctly.
IN Limit Switch
NOTE: The "in" limit switch is not adjusted when the Direct Response system is installed. The system
electronics monitors the motor and shuts the motor off when the awning is fully retracted.
If the "in" limit switch is accidently adjusted, the motor may shut off before the awning is fully closed. If this
occurs, turn the "in" adjustment screw clockwise. It is not necessary that the screw matches the closed
position. The Direct Response electronics controls the closed position.
Endcap Plug
WM011a
“OUT”
“IN” 4mm Hex
4mm Hex