Carefree PARAMOUNT User manual

052548-301r1 Printed in USA September, 2008
SERVICE MANUAL
PARAMOUNT
RV
2-Stage Multi-Position Awning

PROPRIETARY STATEMENT
The Paramount Awning is a product of Carefree of Colorado, located in Broomfield, Colorado, USA. The
information contained in or disclosed in this document is considered proprietary to Carefree of Colorado.
Every effort has been made to ensure that the information presented in the document is accurate and
complete. However, Carefree of Colorado assumes no liability for errors or for any damages that result
from the use of this document.
The information contained in this manual pertains to the current configuration of the models listed on the
title page. Earlier model configurations may differ from the information given. Carefree of Colorado
reserves the right to cancel, change, alter or add any parts and assemblies, described in this manual,
without prior notice.
Carefree of Colorado agrees to allow the reproduction of this document for use with Carefree of Colorado
products only. Any other reproduction or translation of this document in whole or part is strictly prohibited
without prior written approval from Carefree of Colorado.
SAFETY INFORMATION
WARNING
AWARNING INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH,IF NOT AVOIDED,COULD RESULT IN
DEATH OR SERIOUS INJURY AND/OR MAJOR PROPERTY DAMAGE.
CAUTION
ACAUTION INDICATES A POTENTIALLY HAZARDOUS SITUATION THAT MAY CAUSE MINOR TO MODERATE
PERSONAL INJURY AND/OR PROPERTY DAMAGE.IT MAY ALSO BE USED TO ALERT AGAINST UNSAFE PRACTICES.
NOTE: A note indicates further information about a product, part, or step.
Tip: A tip provides helpful suggestions.
Safety Notes:
•Always disconnect battery or power source before working on or around the electrical system.
•Always wear appropriate safety equipment (i.e. goggles).
•Always use appropriate lifting devices and/or helpers when lifting or holding heavy objects.
•When using fasteners, use care to not over tighten. Soft materials such as fiberglass and aluminum
can be "stripped out" and lose the ability to grip and hold.
Reference Publications located @ www.carefreeofcolorado.com:'
052548-001 Paramount Installation Manual
052548-201 Paramount Owner's Manual
052548-301 Paramount Service Manual
Carefree of Colorado 2145 W. 6
th
Avenue Broomfield, CO 80020
aScott Fetzer company 303-469-3324 ♦www.carefreeofcolorado.com

Carefree of Colorado Service Manual PARAMOUNT
052548-301r1 1
TABLE OF CONTENTS
Product Overview.......................................................................................................................... 2
Paramount Patio Awning Specifications .............................................................................................2
Canopy Replacement.................................................................................................................... 3
Short Spring Arm Replacement ................................................................................................... 4
Removing the Existing Arm.................................................................................................................4
Installing the New Arm ........................................................................................................................5
Long Spring Arm Replacement.................................................................................................... 6
Removing the Existing Arm.................................................................................................................6
Installing the New Arm ........................................................................................................................6
Motor Replacement ....................................................................................................................... 7
Removing the Awning................................................................................................................... 9
Diagnostic Tests.......................................................................................................................... 10
Common Operation Items.....................................................................................................................10
Testing the System ...............................................................................................................................11
Electronics ................................................................................................................................... 15
Wiring Diagram – Single Awning ..........................................................................................................15
Wiring Diagram – 2-Awnings ................................................................................................................16
Wiring Diagram – 4 Awnings ................................................................................................................18
Connection Flex w/ "110VDR" Control Boxes ......................................................................................20
Optional Manual Bypass Switch ...........................................................................................................20
Control Board Replacement - Direct Response....................................................................................21
Sensor Replacement ............................................................................................................................22
Standard Service Procedures .................................................................................................... 23
Setting the Motor Limits........................................................................................................................23
Adjusting the OUT Limit Switch.........................................................................................................23
Adjusting the IN Limit Switch.............................................................................................................23
Adjusting the Lead Rail.........................................................................................................................24
Adjusting the Lead Rail Height..........................................................................................................24
Adjusting the Horizontal Lead Rail Position ......................................................................................24
Manual Override ...................................................................................................................................25
Programming the RF Receiver for a Remote .......................................................................................26
Standard Maintenance ................................................................................................................ 27
Fabric Care...........................................................................................................................................27
Mildew ...............................................................................................................................................27
Pooling ..............................................................................................................................................27
Arm Care ..............................................................................................................................................27
Arm Noise .........................................................................................................................................27
Part Number Listing .................................................................................................................... 28
Illustrated Parts List ..............................................................................................................................28
Part Number Configuration ...................................................................................................................30

PARAMOUNT Service Manual Carefree of Colorado
2 052548-301r1
PRODUCT OVERVIEW
The Paramount Patio Awning offers the coach owner an awning system that provides as much or as little
shade as required. The canopy is housed in an aluminum case that easily blends in with the coach roof.
Each unit is equipped with lateral support arms that are the strongest available on the market. No vertical
arms interfere with coach sidewalls or equipment that may be mounted on the roof.
The unique and innovative 110V electronic control system provides Carefree’s Direct Response system with
interior pushbutton controls for standard extend/retract functions. At the master control panel the auto-retract
system can be engaged to automatically retract the awning in windy conditions. Sensitivity can be set to respond
to a variety of wind speed conditions. An RF remote is furnished with the Direct Response system.
Paramount Patio Awning Specifications
The following information is for reference only.
7.13”
12.75”
A (Awning Length)
Paramount001
Top View Profile
LENGTH 14’ – 21’ (in 1 foot increments)
Position: Slide-Out Window Patio
EXTENSION: 40" 72" 106"
LEAD RAIL DROP 6" (20°) 32" (33°) 51" (33°)
Values are approximate, actual dimensions may vary with specific installations.
Angles are measured from horizontal (parallel to ground)
MOTOR SPECIFICATIONS:Available in LH or RH configurations
Type: Tubular Motor
Power: 120V, 60HZ, 2.5A
Torque: 60 nm
Speed: 14 RPM
Cycle: 40 Sec ON / 1 Min OFF
CONTROLS: Direct Response Electronics with a single master control and single remote for all awnings.
COLOR: Hardware: White, Black
Fabric: Woven Acrylic Fabric
APPROXIMATE INSTALLED WEIGHT (LBS.)
Awning Length (ft.) Weight Awning Length (ft.) Weight Awning Length (ft.) Weight
14 195 17 227 20 258
15 212 18 234 21 266
16 220 19 246

Carefree of Colorado Service Manual PARAMOUNT
052548-301r1 3
CANOPY REPLACEMENT
During the following instructions, use the manual override procedure on page 24 to open and close the awning.
CAUTION
WHEN MOVING AN AWNING OR LIFTING THE ROLLBAR AND MOTOR OUT OF THE CASE,THE SERVICING TECHNICIAN
MUST USE CARE TO NOT BREAK OR DAMAGE THE MOTOR AND SENSOR CABLES.
1. Disconnect power to the awnings.
2. Remove the top screws holding the top cover. Rotate
the top cover back and out of the way. If rotated back
without obstructions, the top cover will disengage from
the pivot rail and can be set aside.
3. Open the awning to be serviced several inches to
expose the arm elbows.
4. (refer to Detail A) Using a minimum 1/2" rope, firmly tie
the elbows of the outer spring arms together, do not use
bungee cords. When tying the rope, use a non-slip knot
such as a square knot or equivalent.
5. Using rope or heavy duty plastic ties (3/8" x 12") tie the long
arms and middle rail together in the closed position.
CAUTION
FAILURE TO SECURE THE ARMS AS DESCRIBED WILL
ALLOW THE SPRING ARMS TO UNEXPECTANTLY EXTEND
OUT POSSIBLY CAUSING PERSONAL INJURY AND DAMAGE
TO THE AWNING.
6. (Refer to Detail B) Remove the two fabric retainer
screws on both sides of the lead rail and set aside.
7. Use the manual override to unroll the canopy until the roll
bar slot holding the canopy and polyrod is exposed.
8. (refer to Detail C) Remove the screws holding the idler
end plate and remove plate from case and set aside.
9. From the idler end of the rollbar, simultaneously slide
the old canopy out of the roller tube and lead rail.
NOTE: It will be necessary to support the roll bar do not allow the rollbar to pull off the motor.
10. Inspect the slots in the roll bar and lead rail. Clean and deburr as required. Lightly spraying the inside
of the slot with a dry silicone lubricant will aid in sliding the new fabric in.
11. Slide the new canopy into the lead rail and roller. Both edges must be done at the same time. Orient
the fabric so that the large polycord goes into the lead rail, the smaller polycord goes into the roll bar.
The hem should be on the down side.
12. Center the canopy into the slots of the rollbar and lead rail.
13. Reattach the end plate to the case with the roll bar idler seated into the glide bearing.
14. Use the manual override to roll the canopy onto the rollbar, the material rolls over the top of the roll bar.
Ensure the fabric rolls evenly onto the rollbar.
15. Once the fabric is snugly rolled up, remove the rope used to secure the arms previously.
16. Restore power to the awning.
17. Extend and retract the awning several times. This will allow the canopy to self-center.
NOTE: It may be necessary to adjust the motor limits. Refer to page 23.
18. Install the fabric retainer screws in the lead rail.
19. Install the top cover.
Tie the Elbows of the
Outer Short Arms
Tie the Middle Rail
and Long Arms in the
Closed Position
End Plate
Cover (ref)
Roll Bar (ref)
Paramount016
DETAIL A
Retaining
Screw
DETAIL
C
DETAIL B
Figure 1. Canopy Replacement.

PARAMOUNT Service Manual Carefree of Colorado
4 052548-301r1
WARNING
NEVER ATTEMPT TO ADJUST OR ALTER THE MIDDLE RAIL AND ATTACHED COMPONENTS.NEVER ATTEMPT TO
MOVE OR ADJUST THE ARM KNUCKLES IN THE CASE OR ON THE MIDDLE RAIL;THESE HAVE BEEN PRE-SET AT THE
FACTORY FOR OPTIMUM OPERATION.
SHORT SPRING ARM REPLACEMENT
CAUTION
THE SPRING ARM IS UNDER TENSION TO OPEN.USE EXTREME CARE TO FIRMLY HOLD THE SPRING ARMS DURING
ASSEMBLY AND DISASSEMBLY TO AVOID ANY SUDDEN OR UNEXPECTED MOVEMENT BY THE ARM.SERIOUS
PERSONAL INJURY AND/OR PROPERTY DAMAGE COULD OCCUR.
IMPORTANT NOTE: Two styles of case knuckles are used on the
Paramount short arms. Early units use the 1-piece
knuckle. Later models use the knuckle with positioning
pins. Replacement arms use the knuckle with
positioning pins.
Removing the Existing Arm
1. Extend the awning out to the Slide-Out Cover
position.
2. Disconnect power to the awning.
3. For arms with the sensor cable mounted,
carefully remove the sensor cable from the
wire channel on top of the arm. Use care to
not bend, break or compromise the cable.
4. (Refer to Detail A) Remove the 1/2-13 bolt and
washers from the frame mount. Save the screw
and washers.
5. Remove the knuckle plate and screws. If
installed, remove the positioning pins. It may be
necessary to gently lift and pull the arm to slide
the pins out of the housing.
6. While firmly holding the arm, pull the arm
knuckle out of the housing.
7. Fold the arm together and securely tie the arm
closed. Use a 3/8" x 12" plastic tie or
equivalent.
8. Rotate the arm so that it is parallel with the
middle rail to provide access to the set screw
located in the arm knuckle.
9. (Refer to Detail B) Remove the set screw and rotation pin from the arm knuckle.
10. Remove the arm from the awning and set aside.
11. If the arm has wire channel mounted for the sensor cable, carefully remove the channel from the arm to
reuse on the new arm.
1-Piece Knuckle Knuckle w/
Positioning Pins
paramount18b
Figure 2. Knuckle Styles.
B
A
DETAIL A
DETAIL B
Middle Rail
Rotation Pin
#8-32 Set Screw
Arm
Paramount018d
Positioning Pins
Knuckle Plate
1/2” Bolt
& Washers
Knuckle
Housing
Optional
Brass Shim(s)
Optional
Brass Shim(s)
Figure 3. Short Arm Replacement.

Carefree of Colorado Service Manual PARAMOUNT
052548-301r1 5
Installing the New Arm
The new arm is banded in the closed position. Do not remove the binding until instructed to do so.
1. (Refer to Detail B) Attach the arm to the middle rail joint using the rotation pin and set screw removed
previously. Ensure that the groove in the pin aligns with the set screw.
2. Firmly hold the arm together and remove the binding. Allow the arm to slowly open.
CAUTION
WHEN THE ARM IS CLOSED,IT CAN OPEN WITH SIGNIFICANT FORCE.USE CARE WHEN OPENING THE ARM.
3. (Refer to Detail A) Slide the arm knuckle into the frame mount.
4. For models with positioning pins:
•Liberally coat the positioning pins with quality silicone grease.
•For awnings under 19' long, two (2) pins are used for the inner and outer
arms in the positions shown. For awnings 19' and longer, the inner arms
use the two pins, the outer arms use one (1) pin in the position shown.
•Slide the positioning pins into the housing with the knuckle. It may be
necessary to gently lift the arm up or down to slide the pins into the
housing with the knuckle.
•Attach the knuckle plate to the housing using the screws removed
previously.
5. Attach the knuckle to the mount using the 1/2-13 bolt, washer and lock washer removed previously. Do
not tighten at this time.
6. (refer to Detail A on page 4) The arms are tested at the factory for the correct seating to level the arm.
The adjustment to seat the arm is accomplished by using brass shims between the flange of the
knuckle and housing at either the top or bottom of the knuckle. The required shims for each arm are
taped to the arm with the notation for placement (i.e. 2 on top or 1 on bottom etc). Ensure that the
shim(s) are in place between the knuckle flange and housing before going to the next step.
NOTE: Each arm is tested separately. The quantity and placement of the shims are unique to
each arm.
7. Tighten the 1/2-13 bolt.
8. If the sensor cable is routed on the replacement arm:
•Attach a piece of wire channel to the top of each section of the arm. If using new channel, cut each
piece slightly shorter than the arm extrusion. Attach the channel using double sided tape.
•Route the cable through the wire channel. At the arm joints, arch the cable slightly to avoid binding.
Do not twist the cable.
Tip: Use a small tool, such as a flat bladed screwdriver to gently spread open the channel then
insert the cable. Do this for the entire length of the channel until the cable is fully inserted.
Paramount018c
Pin Position
(2 per knuckle)
Pin Position
(1 per knuckle)
For All Inner Arms &
Outer Arms In Units under 19’
For Outer Arms In Units over 19’
Figure 4. Pin Positions.

PARAMOUNT Service Manual Carefree of Colorado
6 052548-301r1
WARNING
NEVER ATTEMPT TO ADJUST OR ALTER THE MIDDLE RAIL AND ATTACHED COMPONENTS.NEVER ATTEMPT TO
MOVE OR ADJUST THE ARM KNUCKLES IN THE CASE OR ON THE MIDDLE RAIL;THESE HAVE BEEN PRE-SET AT THE
FACTORY FOR OPTIMUM OPERATION.
LONG SPRING ARM REPLACEMENT
CAUTION
THE SPRING ARM IS UNDER TENSION TO OPEN.USE EXTREME CARE TO FIRMLY HOLD THE SPRING ARMS DURING
ASSEMBLY AND DISASSEMBLY TO AVOID ANY SUDDEN OR UNEXPECTED MOVEMENT BY THE ARM.SERIOUS
PERSONAL INJURY AND/OR PROPERTY DAMAGE COULD OCCUR.
Removing the Existing Arm
1. Extend the awning out fully
2. Disconnect power to the awning.
3. For arms with the sensor cable mounted, carefully
remove the sensor cable from the wire channel on
top of the arm. Use care to not bend, break or
compromise the cable.
4. (Refer to Detail A) Firmly hold the arm while
removing the set screw and rotation pin from the
middle rail knuckle.
5. Fold the arm together and securely tie the arm
closed. Use a 3/8" x 12" plastic tie or equivalent.
6. Rotate the arm so that it is parallel with the lead
rail to provide access to the set screw located in
the arm knuckle.
7. (Refer to Detail B) Remove the set screw and
rotation pin from the arm knuckle.
8. Remove the arm from the awning and set aside.
9. If the arm has wire channel mounted for the sensor
cable, carefully remove the channel from the arm
to reuse on the new arm.
Installing the New Arm
The new arm is banded in the closed position. Do not
remove the binding until instructed to do so.
1. (Refer to Detail B) Attach the arm to the lead rail connector using the rotation pin and set screw
removed previously. Ensure that the groove in the pin aligns with the set screw.
2. Firmly hold the arm together and remove the binding. Allow the arm to slowly open.
CAUTION
WHEN THE ARM IS CLOSED,IT CAN OPEN WITH SIGNIFICANT FORCE.USE CARE WHEN OPENING THE ARM.
3. (Refer to Detail A) Attach the arm to the middle rail knuckle using the rotation pin and set screw
removed previously. Ensure that the groove in the pin aligns with the set screw.
4. If the sensor cable is routed on the replacement arm:
•Attach a piece of wire channel to the top of each section of the arm. If using new channel, cut each
piece slightly shorter than the arm extrusion. Attach the channel using double sided tape.
•Route the cable through the wire channel. At the arm joints, arch the cable slightly to avoid binding.
Do not twist the cable.
Tip: Use a small tool, such as a flat bladed screwdriver to gently spread open the channel then
insert the cable. Do this for the entire length of the channel until the cable is fully inserted.
B
A
DETAIL A
DETAIL B
Middle Rail
#8-32 Set Screw
Arm
Rotation Pin
Arm
#8-32 Set Screw
Rotatation Pin
Lead Rail
Motion Sensor (ref)
Paramount019
Figure 5. Long Arm Replacement.

Carefree of Colorado Service Manual PARAMOUNT
052548-301r1 7
MOTOR REPLACEMENT
During the following instructions, use the manual override procedure on page 24 to open and close the awning.
For multiple awning installations where the awnings are mounted end to end it will be necessary to move the
unaffected awning if the motors are next to each other.
CAUTION
WHEN MOVING AN AWNING OR LIFTING THE ROLLBAR AND MOTOR OUT OF THE CASE,THE SERVICING TECHNICIAN
MUST USE CARE TO NOT BREAK OR DAMAGE THE MOTOR AND SENSOR CABLES.
Tie the Elbows of the
Outer Short Arms
Tie the Middle Rail
and Long Arms in the
Closed Position
End Plate Assy
Drive
Crown Motor
Cover
(ref)
Roll Bar (ref)
Paramount017
1. Disconnect power to the awning(s).
2. Locate the junction box inside the coach and disconnect the motor wires.
3. (refer to Detail A) To move an adjacent unaffected awning:
2.1 Close the awning if open.
2.2 Loosen the retaining bolts in the back of the mounting plates.
2.3 Slide the awning away from the other awning; allow a minimum of 6" to 8" between awnings. See
Caution above.
2.4 Temporarily tighten at least one of the retaining screws.
4. Open the awning to be serviced several inches to expose the arm elbows.
5. (refer to Detail B) Using a minimum 1/2" rope, firmly tie the elbows of the outer short spring arms together,
do not use bungee cords. When tying the rope, use a non-slip knot such as a square knot or equivalent.
6. Using rope or heavy duty plastic ties (3/8" x 12") tie the long arms and middle rail together in the closed
position.
CAUTION
FAILURE TO SECURE THE ARMS AS DESCRIBED WILL ALLOW THE SPRING ARMS TO UNEXPECTANTLY EXTEND
OUT POSSIBLY CAUSING PERSONAL INJURY AND DAMAGE TO THE AWNING.
7. Remove the top screws holding the top cover. Rotate the top cover back and out of the way. If rotated
back without obstructions, the top cover will disengage from the pivot rail and can be set aside.
8. Use the manual override to partially unroll the canopy to provide slack in the fabric.
9. (refer to Detail C) Remove the screws holding the end plate.
10. Carefully lift up and pull the end plate, motor and rollbar until the idler shaft clears the end plate on the
other end. Rest the motor and roll bar on the case or a flat surface. Use care to not stretch or damage
the canopy.
11. If not previously done, disconnect the motor wires from inside the coach and pull out.
12. Remove the screws and nuts holding the motor to the end plate. Set the end plate aside. Note the
orientation of the motor then pull the motor, crown and drive out of the roll bar.

PARAMOUNT Service Manual Carefree of Colorado
8 052548-301r1
13. Remove the drive gear and crown from the existing motor and install on the new motor
14. Attach the new motor assembly to the end plate using the screws and nuts removed previously.
15. Slide the new motor assembly into the roll bar. Ensure that the motor drive gear and crown are
properly seated inside the roll bar.
16. Lift rollbar and canopy up and insert the idler shaft into the idler end plate.
17. Position motor end plate on the case and attach using the screws removed previously.
18. Route the new motor wire into the coach and attach (refer to wiring diagrams on page 12 for the
appropriate control system). Ensure that the wire colors match (i.e. red to red and black to black). All
wiring must conform to NEC (National Electrical Code) and local codes.
19. Use the manual override to roll the canopy onto the rollbar. Ensure the fabric rolls evenly onto the rollbar.
20. Once the fabric is snugly rolled up, remove the rope and ties used to secure the arms.
21. Restore power to the awning.
22. Extend and retract the awning several times. This will allow the canopy to self-center.
23. It will be necessary to adjust the motor limits. Refer to page 23.
24. Install the top cover.
25. Reposition the adjacent awning if it has been moved. Ensure that all the retaining bolts are properly
tightened to 10 ft-lbs.
26. After replacing the motor, it is recommended that a calibration routine is run on the affected awning
because of possible variations in motor performance. Refer to page Error! Bookmark not defined..

Carefree of Colorado Service Manual PARAMOUNT
052548-301r1 9
REMOVING THE AWNING
WARNING
THE PARAMOUNT AWNING IS EXTREMELY HEAVY.MOVING AND/OR LIFTING THE AWNING REQUIRES A MINIMUM
OF 3PEOPLE.THE USE OF A LIFTING DEVICE IS STRONGLY RECOMMENDED.
1. Retract the awning completely.
2. Disconnect power to the awning.
3. Locate the junction box where the motor wires are routed. Disconnect the motor wires and remove
from the junction box. Make note of the wire colors. Bundle the wire to the awning.
NOTE: Some installations use a waterproof junction box located on the top of the coach, others
may have the junction box located inside the coach at or near the cable entry point.
4. Disconnect the sensor cable.
•For installations with a junction box:Some installs may route the cable into a junction box with a cable
coupler. Disconnect the cable from the awning and remove from the junction box. Bundle the cable to
the awning.
•For installations hardwired to the control box (option 1). Trace the cable to the control box. Disconnect
the cable from the control box and remove from the coach. Bundle the cable to the awning.
•For installations hardwired to the control box (option 2). If it is not possible to disconnect the cable from
the control box and remove from the coach, locate the cable inside the coach and at a convenient point,
cut the cable. Pull the cable out and bundle to the awning. If using this method, it will be necessary to
order a cable coupler and two phone cable connectors when reinstalling the awning.
5. The awning is mounted using 4 mounting
brackets attached to the roof of the coach.
Each mounting bracket has a retaining bolt in
the back side to hold the awning into the
bracket. Loosen all 4 of the retaining bolts. It
is not necessary to remove the bolts from the
brackets.
6. Slide the awning back and up to remove the
awning from the brackets.
7. To reinstall the awning, reverse the procedure above.
Special Notes:
a) When attaching the motor wires ensure that the wire colors match the previous configuration. All
wiring must conform to NEC (National Electrical Code) and local codes.
b) If the sensor cable was cut to remove the awning, it is necessary to install a connector on each cut
end of the cable. The connector must be attached as shown in the wiring diagrams on page
Error! Bookmark not defined.. A coupler is then used to attach the two connectors.
8. After installing the awning, test the operation (refer to page 11). It may be necessary to adjust the lead
rail height (refer to page Error! Bookmark not defined.).
Paramount020
Profile
5/16-18 x 1 1/2
Retaining Bolt & Square Nut
(1 per bracket)
Mounting Bracket
(ref)
Figure 6. The Awning Mount.

PARAMOUNT Service Manual Carefree of Colorado
10 052548-301r1
DIAGNOSTIC TESTS
The following procedures are intended to aid the service technician to logically resolve operational issues with the
Direct Response installation.
WARNING
ALWAYS DISCONNECT POWER WHEN CONNECTING OR DISCONNECTING 110VAC WIRES.
Refer to the appropriate wiring diagram:
Wiring Diagram – Single Awning page 15
Wiring Diagram – 2 - Awnings page 16
Wiring Diagram – 4 - Awnings page 18
Procedures in this section: Page
COMMON OPERATIONAL ITEMS .......................................................................................................................10
TESTING THE SYSTEM.....................................................................................................................................11
D01 -THE AWNING(S)OPERATE DIFFERENT THAN THE SWITCH MARKINGS........................................................12
D02 -THE AWNINGS DO NOT OPERATE (ALL).................................................................................................12
D03 -ONE AWNING DOES NOT OPERATE .......................................................................................................13
D04 -AWNING(S)DO NOT RETRACT DURING WINDY CONDITIONS ...................................................................13
D05 –AWNING(S)DO NOT MOVE WHEN REMOTE CONTROL BUTTONS ARE PUSHED.......................................14
COMMON OPERATION ITEMS
The following items are operational items that may come up as questions during normal operation. These are
also given in the operator's manual.
1. Each awning has an independent motion sensor. During windy conditions, the awnings may not retract
concurrently.
2. The auto-retract system functions in two stages. The first stage is when the awning is extended past the slide-
out position. The awning will retract and stop at the slide-out cover position to provide continued protection for
the slide-out room.
When in the slide-out cover position, the awning is very robust. The auto-retract system is active but uses a
higher factory preset threshold value for extreme weather conditions. When the motion of the awning exceeds
the extreme weather threshold, the awning will close to the full retract position. The second stage sensitivity
(threshold) value is not controlled by the keypad settings.
3. If an optional EL ignition lockout is installed, the system will disable the extend function while the vehicle
ignition key is in the ON position. If the RTL ignition lockout with retract is installed, the awning will retract to
the closed position and disable the extend function. Operation will return to normal when the key is OFF.
4. If the AC power source is disrupted while the awning is moving, the awning will stop. When power is
restored, extend and retract functions will operate normally. Pressing an intermediate stop (slide-out
and window) the awning will first retract then go to the selected position.

Carefree of Colorado Service Manual PARAMOUNT
052548-301r1 11
TESTING THE SYSTEM
All function buttons are press ON. The auto-functions continue until the awning is fully extended or
retracted. Pressing the button a second time will stop the function (does not apply to the "Extend All" or
Retract All" commands). It is not necessary to hold the button while the function is active.
1. While observing the control panel, have a second person initiate 110VAC power to the coach and
awning system. The following should occur:
1.1 The System Indicator and Sensitivity Level LEDs will briefly illuminate.
1.2 The system then goes to the default settings: The default settings are the last known state when
the AC power source was suspended. Example: If power was "ON" and the sensitivity was set to
"2", when AC power is applied, power will be on and sensitivity will be set to "2".
2. If ON press the POWER “OFF”. ALL LEDs should be extinguished. The POWER ON/OFF button disables all
functions including Auto-Retract and the RF remote. It does not disconnect the 110VAC power.
3. Check the extend function.
3.1 Press the POWER “ON.
3.2 Press the Awning #1 EXTEND button. The awning should extend.
3.3 Press the extend button again. The awning should stop
3.4 Press the extend button a third time. Observe the awning, it should fully extend. The system performs
an auto-tension action when the awning is fully extended. The awning rolls in reverse to tension the
fabric. The auto-tension feature works only with the extend function when the awning is fully extended.
4. Check the retract function.
4.1 Press the Awning #1 RETRACT button. The awning should retract.
4.2 Press the retract button again. The awning should stop
4.3 Press the retract button a third time. Observe the awning; it should fully retract to the closed position.
NOTE: If the awning moves in the opposite direction than the label, the red and black MOTOR
wires are reversed in the control box.
5. Repeat steps 3 and 4 for each of the Extend/Retract button combinations.
6. Test the mid-position functions. Press and release each mid position button (Slide-Out cover and Window).
The awning should extend or retract to the specified position.
7. Test the Auto-Retract function:
8.1 Fully extend awning #1.
8.2 Set the WIND SPEED to the lowest setting.
8.3 Create a firm but gentle vertical rocking motion with the leading edge of the awning. The awning should
retract after 2-3 seconds of the motion. The awning will retract to the slide-out position.
8. Repeat step 6 for each of the awnings.
9. If the optional Ignition Sensor is installed:
10.1 Partially retract the awning.
10.2 Turn the vehicle ignition key ON.
10.3 If the RTL lockout is installed, the awning(s) will retract.
10.4 Press the EXTEND button. The awning(s) should not extend.

PARAMOUNT Service Manual Carefree of Colorado
12 052548-301r1
In the charts below, YES is a positive response to the test; NO is a negative response.
D01 THE AWNING(S)OPERATE DIFFERENT THAN THE SWITCH MARKINGS
The power switch at the key pad must be on; the LED will be illuminated if power is present.
YES Awning #Y moves when Awning #X
buttons are pressed.
- Awning motor wires from Awning #X
and Awning #Y are reversed. Remove
motor wires from control boards,
reattach motor #X wires to motor #X
control board; motor #Y wires to motor
#Y control board.
A Does a different awning move when pressing the controls
are pressed (i.e. Awning #2 moves when Awning #1 is
pressed)?
Board marked "Motor 1" corresponds with key pad "Awning
1" etc.
NO Go to test B
YES Motor wires from affected awning are
reversed in control box.
- Open control box and locate motor
wires from affected awning. Reverse
the red and black wires.
NOTE:
For LH motor configurations:
RED WIRE goes to terminal (1);
BLACK WIRE goes to terminal (2).
For RH motor configurations:
BLACK WIRE goes to terminal (1):
RED WIRE goes to terminal (2).
B Does the awning operate in reverse of the switch plate
labeling (i.e. extends when retract is pushed)
NO Reanalyze condition
D02 THE AWNINGS DO NOT OPERATE (ALL)
For one awning that does not operate, refer to D03
YES Power is present; go to test B
A Confirm 110VAC power to control box
1. Shut off power source.
2. Open control box.
3. On some early units a fuse is installed on the circuit
board. Check that fuses on circuit boards are intact.
4. Check that 110VAC connections and splices to the
boards are correct and secure. Refer to system
schematics.
5. While observing the circuit boards, have power restored.
The LEDs on the boards should blink red then green.
NO Check vehicle circuits and fuses.
Repair as required and retest
B Confirm that key pad is operating.
YES Power is on, go to step B-3
1 Press the "Power On" button on the key pad. The
"Indicator" LED should illuminate. NO LED does not illuminate, go to step B-2
YES Continuity OK; go to step B-3
2 Check the cable between the keypad and control box.
As a continuity check, Pin 1 of connector 1 goes to Pin
1 of connector 2; pin 2 goes to pin 2; pin 3 goes to pin 3
and pin 4 goes to pin 4. NO Replace cable and retest
YES Awning operates, Controller #1 is
defective – Replace control box.
3 4.1 Disconnect jumper cable between controller boards.
4.2 Disconnect key pad from "ACC" of controller #1
and connect to "ACC" of controller #2.
4.3 Does Awning #2 operate when pressing a
command button on the key pad?
NO Awning does not respond, key pad is
defective - replace

Carefree of Colorado Service Manual PARAMOUNT
052548-301r1 13
D03 ONE AWNING DOES NOT OPERATE
NOTE: The awnings are programmed sequentially (i.e. #1, #2, #3, #4). If power is missing from an awning, the
subsequent awnings will not function (i.e. #1 and #2 works, #3 and #4 don't). Check the power to the first non
functioning control board in sequence (i.e. #3) and correct as necessary before proceeding.
YES Awning functions, control board of non-
working awning is defective – replace
control box.
A 1. Shut off power source if not already done.
2. Open control boxes and disconnect the non-working
awning motor wires and a working awning's motor wires.
3. Connect the non-operating awning to the functioning
control board (i.e. awning #2 to control board #1).
4. Restore power
5. Test the operation of the awning using the controls for
the functioning awning (in the example above #1
awning).
NO Return wires to original configuration.
Go to step B
B Confirm awning motor is functioning
YES Awning motor is good, control box is
defective - replace
1. 1.1 With power off, connect awning motor directly to
110VAC power source.
White = Hot
Green = Ground
Red & Black are Motor Direction Control – connect
one
1.2 Briefly apply power.
1.3 Does awning move when power is applied?
NO Go to step B-2
YES Continuity is good, motor is defective –
replace
2. Test continuity and connections of motor wire between
control box and awning motor.
NO Repair as required and retest
D04 AWNING(S)DO NOT RETRACT DURING WINDY CONDITIONS
The Direct Response auto-retract system operates by gauging the motion of the awning's leading edge, not by the
direct wind speed. Refer to the description in the owner's manual.
NOTE: The awnings have independent sensors and may not retract concurrently.
YES The flashing LED indicate that the
sensor(s) have been disengaged or
other wise disabled. Go to step C
A Press the power on button then press the auto-retract button.
Does the indicator LED flash (slow pulse)?
NO Go to test B
YES Operation is normal, Go to step C
B Confirm standard awning operation. From the key pad,
operate the awnings. NO Refer to the appropriate test D02 or
D03
YES The affected awning retracts. Original
sensor is defective replace.
Return second shaker to the unaffected
awning controller.
C Check function of shaker sensor
1. Open the affected awning (does not have to be open all
the way).
2. Open the second awning.
3. Open control box and disconnect sensor from controller
board of awning that does not auto-retract.
4. If cable has been spliced between sensor and control
box, check continuity of splice. Repair as required and
retest before proceeding.
5. Disconnect the sensor from the other controller and plug
the cable into the "SHAKE" terminal of the affected
awning controller.
6. At key pad, turn power ON and auto-retract ON.
7. Set auto-retract to the lowest setting.
8. At the unaffected awning, create a firm but gentle
rocking motion with the leading edge of the awning for
about 3-4 seconds.
NO Awning does not retract, control box is
defective – replace
NOTE: The key pad LEDs will continue to flash after connecting good sensors. It is necessary to power off the
system then turn it back on so that the key pad recognizes the sensors are connected

PARAMOUNT Service Manual Carefree of Colorado
14 052548-301r1
D05 AWNING DOES NOT MOVE WHEN REMOTE CONTROL BUTTONS ARE PUSHED
1. Confirm power is ON at the key pad -- Correct as required
2. Confirm batteries in remote are good. Pressing any
button on the remote will illuminate the LED at the top
of the remote.
Replace as needed
YES Cable is OK. Confirm that cable is
securely plugged in; go to step 4
3. Check the cable between the Receiver and control box. As
a continuity check, Pin 1 of connector 1 goes to Pin 1 of
connector 2; pin 2 goes to pin 2; pin 3 goes to pin 3 and pin
4 goes to pin 4.
Cable must be plugged into the "BUS" port of controller #1.
NO Repair or Replace cable as required.
4. Confirm that the Receiver is programmed for the
Remote
-- Refer to “Programming the Receiver”
on page Error! Bookmark not
defined. and retest. If system does
not work; go to step 5
YES 2nd remote works. 1
st remote is
defective.
5. Program a second remote and test
NO 2nd remote does not work; go to step 6
YES System works OK. 1st receiver is
defective
6. Replace the Receiver and test.
(it will be necessary to program receiver for remote)
NO System does not work. Reinstall 1st
receiver; go to step 7
7. Replace control box --

Carefree of Colorado Service Manual PARAMOUNT
052548-301r1 15
ELECTRONICS
WIRING DIAGRAM –SINGLE AWNING
TO EYE PORT on RP24 Program Mode
Press to Learn Transmitter
UP
RF
Receiver
GRN
BLK
WHT
RED
Key Pad
DR013
Ignition Switched
+12VDC
12VDC
Ground
Ignition
Lockout
Sensor
(Optional)
Splitter
Sensor
Key Pad
Awning #1
3
5
4
2 Conductor 14AWG
NM Wire w/ Gnd
To 110VAC
AMDSUNAUXEYEDSK
BLK
WHT
RED
GRN
grn
wht
blk
1
7
6
5
4
3
2
1
7
6
5
4
3
2
3 Conductor 14AWG NM Wire w/ Gnd
Sensor
Remote
Red
Black
White
Green (Ground)
1Wire Legend:
2For LH Motor Configurations:
Motor Red goes to Pin (1); Motor Black goes to Pin (2)
For RH Motor Configurations:
Motor Red goes to Pin (2) Black; Motor Black goes to pin (1)
3The SO cable from the 110VAC awning motor can only pass through a wall, it cannot be laid up in the wall
and must be connected to NM wire or individual wires in conduit no more than 6 inches past the point of entry.
NOTES:
4
Wires for the Ignition Lock-Out Sensor are not pin specific.
5
Splitter is used only when Optional Lock-Out Sensor is installed. Connect RF Receiver directly to “EYE”
if Lock-Out is not installed.
Detail A
For RH Configuration
Reverse Red & Black Wires
RED
WHT
BLK
GRN
grn
wht
blk
FROM TO (RH CONFIGURATION) TO (LH CONFIGURATION)
Black 1 2
Red 2 1
White 3 3
Motor
Ground
Control Box
6
Control Box
6
White 4 4
Black 5 5
AC Power
Source
Ground
Control Box
7
Control Box
7
Awning Sensor 10’ Cable Control Box “AMD” Control Box “AMD”
Key Pad 60“ Cable Control Box “DSK” Control Box “DSK”
Splitter 60" Cable Control Box "EYE" Control Box "EYE"
RF Receiver 60” Cable Splitter Splitter
Ignition Lockout 60“ Cable Splitter Splitter

PARAMOUNT Service Manual Carefree of Colorado
16 052548-301r1
WIRING DIAGRAM –2-AWNINGS
TO EYE PORT on RP24 Program Mode
Press to Learn Transmitter
UP
RF
Receiver
GRN
BLK
WHT
RED
Key Pad
DR014a
Ignition Switched
+12VDC
12VDC
Ground Ignition
Lockout
Sensor
(Optional)
Sensor #1
Key Pad
Sensor #2
Awning #1
3
5
RED
WHT
BLK
GRN
BLK
WHT
RED
GRN
Wht
Blk
Grn
Wht
Blk
Grn
2 Conductor 14AWG
NM Wire w/ Gnd
To 110VAC
AMDSUNAUXEYEDSK
AMDSUNAUXEYEDSK
1
7
6
5
4
3
2
1
7
6
5
4
3
2
1
7
6
5
4
3
2
3 Conductor 14AWG
NM Wire w/ Gnd
Sensor
GRN
BLK
WHT
RED
Awning #2
Sensor
Remote
3
3 Conductor 14AWG
NM Wire w/ Gnd
DETAIL A
110VAC Power Line In
1
7
6
5
4
3
2
4
4

Carefree of Colorado Service Manual PARAMOUNT
052548-301r1 17
Green (Ground)
White
Red
Black
1Wire Legend:
2Awnings #1 & #4 shown as LH Motor, Awnings #2 & #3 shown as RH Motor
For LH Motor Configurations:
Motor Red goes to Pin (1); Motor Black goes to Pin (2)
For RH Motor Configurations:
Motor Red goes to Pin (2); Motor Black goes to pin (1)
3The SO cable from the 110VAC awning motor can only pass directly through a wall, it cannot be laid up
in the wall and must be connected to NM wire or individual wires in conduit no more than 6 inches past
the point of entry.
NOTES:
4
DR016a
5Wires for the Ignition Lock-Out Sensor are not pin specific.
The RF Reciever and the optional Ignition Lockout may be plugged into any open “EYE” port.
7
6
Cables are 4-wire RJ11 terminated phone cord (straight, no twist)
For screw type terminals: After testing connections, use Loctite 29005 or equivalent
to secure screws in terminal block.
8Terminal block designations are for reference only. Actual boards may not be marked.
Loctite
29005
Screw Type
Terminal Block
FROM TO (MOTOR #1) TO (MOTOR #2)
White 4 4
Black 5 5
AC Power Source
Ground 7 7
Black
Red Refer to Flag Note 2
White 3
Awning #1 Motor
Ground 6
Black
Red Refer to Flag Note 2
White 3
Awning #2 Motor
Ground
6
#1 Sensor 10’ Cable “AMD”
#2 Sensor 10’ Cable “AMD”
Key Pad 25' Cable "DSK"
RF Receiver 60” Cable "EYE" refer to note 4
Ignition Lockout 60“ Cable "EYE" refer to note 4

PARAMOUNT Service Manual Carefree of Colorado
18 052548-301r1
WIRING DIAGRAM –4AWNINGS
TO EYE PORT on RP24 Program Mode
Press to Learn Transmitter
UP
RF
Receiver
GRN
BLK
WHT
RED
Key Pad
DR015a
Sensor #1
Key Pad
Sensor #2
Awning #1
3
4
4
RED
WHT
BLK
GRN
BLK
WHT
RED
GRN
Wht
Blk
Grn
Wht
Blk
Grn
2 Conductor 14AWG
NM Wire w/ Gnd
To 110VAC
RED
WHT
BLK
GRN
BLK
WHT
RED
GRN
AMDSUNAUXEYEDSK
AMDSUNAUXEYEDSK
AMDSUNAUXEYEDSK
AMDSUNAUXEYEDSK
1
7
6
5
4
3
2
1
7
6
5
4
3
2
1
7
6
5
4
3
2
1
7
6
5
4
3
2
1
7
6
5
4
3
2
To 110VAC
3 Conductor 14AWG
NM Wire w/ Gnd
To 110VAC
Sensor
GRN
BLK
WHT
RED Awning #2
Sensor
Remote
3
3 Conductor 14AWG
NM Wire w/ Gnd
GRN
BLK
WHT
RED
Sensor #3
Sensor #4
Awning #3
3
3 Conductor 14AWG
NM Wire w/ Gnd
Sensor
GRN
BLK
WHT
RED Awning #4
Sensor
3
3 Conductor 14AWG
NM Wire w/ Gnd
DETAIL A
110VAC Power Line In
(typical both boxes)
1
7
6
5
4
3
2
Ignition Switched
+12VDC
12VDC
Ground
Ignition
Lockout
Sensor
(Optional)
5