Carlson 2070 User manual

DESIGN STUDIO
MODEL #:
2046 (Fits openings 27” to 47”)
2070 (Fits openings 40” to 70”)
2846 (Fits openings 27” to 47”)
2870 (Fits openings 27” to 47”)
Owner’s Manual
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND
USE OF GATE KEEP INSTRUCTIONS FOR FUTURE USE.
Carlson Pet Products,Inc
14305 Southcross Drive,Suite 105,
Burnsville, MN 55306
Phone:[phone]
Free Standing And Pressure Mount
Wooden Pet Gate

(1)
WARNING:
Adult assembly required. Keep small parts away from pets and
children.
This wooden gate is NOT to be used for Children.
This wooden gate is to be used ONLY for Pets.
Never leave pet unattended.
Use only with lock securely engaged.
Do not use if any components are missing or damaged.
Check daily to be sure the the gate it securely assembled. If used as
a pressure mounted gate, check to make sure gate is tight and secure.
This product will not necessarily prevent all accidents. Proper
supervision is required at all times.
To prevent serious injury or death,securely install the gate
and use according to manufacturer’s
instructions.
Contact Carlson for questions and replacement parts. If in doubt
about the use of your new gate,call our customer care line
952-435-1084.
Carlson Pet Products,Inc.14305 Southcross Drive,Suite 105,
Burnsville, MN 55306.Made in China
Assembly and Installation Instructions
Please read these instructions carefully before installing
your new gate.

Check to make sure that you have the parts shown in
picture.
(2)
Plastic Foot (x2) Adjustable Spindle Rod (x4)
Hex Head Connector
Bolts (x4) Allen Key (x1)
Main Panels

(3)
Preparing for Assembly
Begin by making sure you have all of the parts shown on
the preivous page before starting the assembly. Next, decide
what configuration you will be using the gate in.
If you plan to use the gate in ‘freestanding’ mode,
contiune with the assembly instructions below. If you plan
to use the gate as a pressure mounted gate, turn to page 6
for further instructions.
Freestanding Gate Assembly
Step 1
First, extend the main panels slightly by disengaging the
hinged locking mechanisms. All four must be unlocked to
adjust the gate.
Locked Unlocked

Step 2
Once you have extended the gate slightly, it is now time to
attach one of the plastic legs. Use the supplied connector
bolts and the allen key to do this. Place the leg on the bottom
corner of one side of the main panel. Insert a connector bolt
through the hole on the side of the foot, and into the threaded
insert on the end of the main panel. Use the supplied allen key
to tighten the bolt.
Next, insert another connector bolt into the hole on the
bottom of the plastic leg, into the threaded insert on the
bottom of the main panel. Use the supplied allen key to
tighten the bolt.
NOTE: The connector bolts should be snug but be sure to not
overtighten them!
(4)
insert
bolt here
insert
bolt
here
main panel

(5)
Step 3
Once you have attached one of the plastic feet, assemble
the other side using the remaining plastic foot
and attachment hardware. Refer to Step 2 if needed.
Step 4
With the gate completely assembled and the latch
mechanisms still unlocked, adjust the gate to the size
opening you will be placing it in. Make sure you have
the hinged locking mechanisms in the ‘lock’ position
once you have it adjusted.
ATTENTION: To securely lock the gate in place, the
hinged locking mechanism must be correctly lined up
within the gap between the metal fencing. If
mis-aligned, the lock will not fully engage!
Note: The gate may not fit an opening perfectly due to
the nature of the locking increments.

Step 2 - With all 4 adjustable rods inserted, unlock the
latch mechanisms(see pg3) and adjust the gate width to fit the
opening you will be using it in. Before moving the spindle
wheel to create pressure to mount the gate, be sure that the
latch mechanisms are in the locked(closed) position. Turn the
spindle wheels on each spindle rod so they create even pressure
on the frame of the opening. The gate should be tightly pressured
into the opening so that it cannot be pulled down or moved.
Pressure Mounted Gate Assembly
Step 1
Insert two adjustable spindle
rods into each end of the gate.
They should be inserted into the
non-threaded holes.
Note: Turn the spindle wheel counter-clockwise to tighten
the gate and clockwise to loosen it.
Spindle Wheel
(6)

Periodically check the gate for signs of damage, wear or for
missing components.
Do not use if any part is missing, worn or damaged.
Check the product regularly to make sure all the hardware and
mountings are tightened.
Do not use abrasive cleaners or bleach.
Clean gate by sponging with warm water and mild detergent.
Immediately wipe down gate with a dry towel after cleaning.
CARE AND MAINTENANCE
Carlson Pet Products,Inc
14305 Southcross Drive,Suite 105,
Burnsville, MN 55306
Phone: [phone]
The gate should look like the picture below when finished.