CASPR BLU TILE User manual

CASPR BLU TILE Owner’s
Manual
CAUTION: Read manual carefully for proper procedures and operation.

2
Congratulations
on your purchase of a CASPR Group enhanced air and surface disinfection system.
This unit is designed to be mounted into any standard ceiling tile. Please read
and follow all safety warnings and service procedures outlined in this manual. Use
only genuine CASPR Group replacement parts available from your CASPR Group
Distributor.
If you have any questions concerning this or any CASPR Group product, contact your
CASPR Group Distributor.
Principles of Operation
CASPR BLU Tile (TILE) uses Natural Catalytic Conversion (NCC) to generate safe, low
levels of hydrogen peroxide. NCC technology replicates natural purifying processes
by using a high intensity light to activate a proprietary metal catalytic coating,
converting water vapor into hydrogen peroxide. Hydrogen peroxide acts as an
oxidizer inactivating surface and air pathogens. It can compromise cellular integrity
by disrupting cell walls, or internal molecular structures, rendering contaminants
harmless.
To learn more about the CASPR BLU Tile and other CASPR Group products and
technologies, please visit our website at www.CASPRgroup.com.
Table of Contents
Safety and Warnings .................................................................................... 3
Specications.............................................................................................. 4
Install the Cell Assembly .............................................................................. 5
TILE Installation .......................................................................................... 6
Service and Maintenance .............................................................................. 6
Replacement parts (purchased separately): .................................................... 7
Cell Disposal ............................................................................................... 7
Warranty Information................................................................................... 8

3
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be taken.
READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
WARNING!
To reduce the risk of re, electrical shock, or injury:
• Use only as described in this manual.
•Do not attempt to repair or adjust any of the electrical or mechanical functions.
Contact Customer Service for service information.
• Do not use outdoors or on wet surfaces.
• Do not allow to be used as a toy. Do not allow children around the unit.
• Do not handle appliance with wet hands.
•Do not allow foreign objects to enter the ventilation openings.
•Keep hair, clothing, ngers, and all parts of body away from openings.
• Do not touch NCC bulb with bare hands.
WARNING
WARNING! - UV light in operation. Disconnect unit from
power supply before servicing. Failure to follow warnings
may result in severe eye damage.

4
Specications
Electrical:
110-240 VAC 50/60 Hz 0.5A
277 VAC 50/60 Hz 0.5A (North America only)
Dimensions:
23.9 in. x 23.9 in. x 5.4 in.
60.71 cm x 60.71 cm x 13.72 cm
Mechanical:
158 CFM
Weight:
11.82 lbs
5.36 kg

5
Install the Cell Assembly
1. Remove the security screw and open the grill of the TILE unit.
2. Remove the Bracket Assembly by
unscrewing the top thumb screw.
3. Remove the 2 additional screws
from the Bracket Assembly.
4. Remove the Cell Assembly from the packaging box.
5. Carefully remove bulb from cell housing.
DO NOT touch the bulb with bare hands.
6. Connect Bulb
to socket in the
Bracket Assembly.
7. Attach Cell Housing to
bracket with previously
removed thumb screws (2).
8. Install Assembly on
TILE unit and secure
with top thumb screw.
9. Close grill on TILE and reinstall security screw.

6
TILE Installation
The TILE is designed to be mounted in place of a standard 2 ft x 2 ft ceiling tile.
Installation is only to be performed by a Licensed Electrician or HVAC Installer. A
power switch turns the unit ON and OFF.
1. Remove the ceiling tile where the CASPR unit will be placed.
Be mindful not to place by a return duct.
2. Place the CASPR BLU Tile unit into the open ceiling square.
3. Attach the CASPR BLU Tile unit to structural support beams in the crawlspace
above the ceiling square using galvanized exible gauge vinyl coated wire rope
and a wire rope clip. This can be done using the safety attachments on the
backside of the CASPR Blu Tile unit. Enough tension should be placed on the
wire rope to minimize load on the panel support beams.
4. Hardwire CASPR BLU Tile unit into an available power source using pigtail leads
and conduit connections. This is to be performed by a licensed Electrician or
HVAC Installer.
Service and Maintenance
Your CASPR BLU Tile unit requires replacement of the NCC cells and bulbs every
18-24 months, even if the bulb appears to be operating normally.
Service should only be performed by a qualied HVAC technician. Make sure there
is no power going to the unit prior to handling.
It is recommended maintenance to vacuum the vent openings and clean the under
side of the unit if any dust build-up has accumulated.
A face mask should be worn to prevent inhalation of any particles released into the
air during the process. Eye protection may be necessary when cleaning the unit.

7
5. Carefully remove bulb from cell housing.
DO NOT touch the bulb with bare hands.
6. Connect Bulb
to socket in the
Bracket Assembly.
7. Attach Cell Housing to
bracket with previously
removed thumb screws (2).
8. Install Assembly on
TILE unit and secure
with top thumb screw.
Replacement parts (purchased separately):
NCC Cell (Ozone-Free) CELL-VV-14-001-AP
Cell Disposal
Do NOT throw a used NCC Cell in the garbage. The special germicidal UVC bulb
used in the unit contains a very small amount of mercury. Dispose of the used NCC
Cell and UV Lamp at your local recycling center or by local regulations. To learn
more, visit www.lamprecycle.org.
1. Remove the security screw and open the grill of the TILE unit.
2. Remove the Bracket Assembly by
unscrewing the top thumb screw.
3. Remove the 2 additional screws
from the Bracket Assembly.
4. Remove the Cell Assembly from the packaging box.
9.. Close grill on TILE and reinstall security screw.

Warranty Information
NDS Sales LLC d/b/a CASPR Technologies (as “Seller”) offers the following Express Limited Warranty to a buying customer (a “Buyer”)
of a CASPR product (the “Product”):
Seller warrants to Buyer that (a) the Product will be free from defects caused by faulty workmanship or materials for three years from date
of purchase when operated under normal conditions and in accordance with Seller’s recommended use (the “Product Warranty Period),”
and that (b) the Components (comprised of a bulb and a cell) will be free from defects caused by faulty workmanship or materials for one
year from date of purchase when operated under normal conditions and in accordance with Seller’s recommended use (the “Components
Warranty Period).”
SELLER EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED.
Should Buyer discover acovered defect within the Product Warranty Period or the Components Warranty Period, Seller will repair or
replace (at Seller’s cost) the Product and/or the Components. Buyer’s sole and exclusive remedy for Product or Components defects is
limited to repair or replacement.
To confirm coverage or to schedule repair or replacement under this Express Limited Warranty, Buyer should contact Seller at
www.casprtech.com/warranty and provide the serial number located on the Product and proof of purchase. Absence of a serial number or
proof of purchase may void the Express Limited Warranty.
This Express Limited Warranty does not extend to or cover Product damage caused by accident, fire, flooding, exposure to temperature
extremes, abuse, misuse, improper or unauthorized installation, modification, misapplication, or repairs performed by persons other than
Seller. Repairs performed by persons other than Seller or Seller’s authorized representative will void the Express Limited Warranty.
This Express Limited Warranty does not extend to or cover incidental or consequential damages incurred by Buyer arising from, related
to, or in connection with, any Product or Components defects, including but not limited to downtime costs, loss of use, loss of revenue,
and/or loss of profits.
SALES THROUGH DISTRIBUTOR OR RESELLER
To the extent the Product is purchased by Buyer from an authorized CASPR distributor or reseller, this Express Limited Warranty passes
through to Buyer.
FOR U.S. APPLICATION ONLY
Product warranties are governed by state and federal laws and may vary from state to state. This Express Limited Warranty provides
Buyer with specific assurances regarding repair or replacement of the Product. Other warranties are expressly negated.
FOR CANADIAN APPLICATION ONLY
Canadian, provincial, and territorial sales laws may govern implied warranties. This Express Limited Warranty provides Buyer with
specific assurancesregarding repairorreplacementoftheProduct. Other warranties are expressly negated. Should there be adifference
between this Express Limited Warranty and Canadian law regarding implied warranties, Canadian law will control.
8

9
V. IN-M-T-01-04052021
www.CASPRTECH.com
1343 W. CAUSEWAY APPROACH
MANDEVILLE, LA 70471
[phone]