Castles Technology S1P User manual

S1P POS Terminal
Book 2
User Manual
S1P
Version 1.0
May. 2023
CRT-S1-21-02-V1.0-CE-RCM-CB-FCC-IC-UL
CASTLES TECHNOLOGY
Castles Technology Co., Ltd.
6F, No. 207-5, Sec. 3, Beixin Rd., Xindian District,
New Taipei City 23143, Taiwan R.O.C.
http://www.castech.com.tw

Castles Technology Co., Ltd. Pg. 2
WARNING
Information in this document is subject to change without prior notice.
No part of this publication may be reproduced, transmitted, stored in a retrieval system,
nor translated into any human or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual, or otherwise, without the
prior written permission of Castles Technology Co., Ltd.
All trademarks mentioned are proprietary to their respective owners.

Castles Technology Co., Ltd. Pg. 3
Revision History
Version
Date
Descriptions
Author
1.0
2023.05.03
Initial creation.
Dustin
1.1
2023.07.12
Add FCC/IC/UL
Modify temperature from 45 to 50 degrees C
Dustin
1.2
2023.07.27
Modify temperature from 50 to 40 degrees C
Dustin

Castles Technology Co., Ltd. Pg. 4
Contents
1. Introduction..................................................................................................................5
2. Hardware Setup............................................................................................................6
2.1. Parts of the Terminal ...........................................................................................6
2.2. Insert SAM Card..................................................................................................8
2.3. Insert GSM SIM Card ..........................................................................................9
2.4. Insert Micro SD Card.........................................................................................10
3. Appendix ....................................................................................................................11
3.1. CB.....................................................................................................................11
3.2. FCC...................................................................................................................12
3.3. IC.......................................................................................................................13
3.4. UL / IEC 62368-1...............................................................................................14

Castles Technology Co., Ltd. Pg. 5
1.Introduction
This document provides a guideline for operating and configuring Castles S1P terminal.
The scope of this document includes setting up the terminal, basic operation, application
lifecycle, and some advanced features.
Regulatory instruction of usage
●Before using theterminal, please check has it been disassembled, modified, orshowed
abnormal situation. If yes, please do not use.
●Please stay away from strong electromagnetic waves.
(Example) Microwave ovens, magnets, shoplifting prevention devices, high-voltage
wires, automatic doors, communication antennas, etc.
●Condensation can occur when moving from a cold place to a warm place. If
condensation occurs, do not use the unit until the connected water droplets evaporate.
●Static electricity may occur in some places (such as where you use a carpet).
●Please do not leave it in the sun for a long time.
●Please operate the unit carefully as it is a precision instrument. Do not apply impact,
drop or heavy objects on top of the unit.
●Do not attach dust, oil, etc. to a part of the power terminal. Also, please do not
scratch.
●This device requires connection to AC power for operation and is for installation in a
fixed POS system only(>20cm).

Castles Technology Co., Ltd. Pg. 6
2.Hardware Setup
2.1. Parts of the Terminal
Front
1. Front camera
2. LCD display
3. Keypad
4. Contactless Card
Landing Zone
5. Magnetic Stripe Reader
6. Smart Card Reader
1
2
3
5
4
6

Castles Technology Co., Ltd. Pg. 7
Rear
7. Back cover
8. Speaker
9. Product label
10. port for power cable and transmission cable
11. SAM slots 1-2
12. GSM SIM card slots 1-2
13. Micro SD Card Slot
7
13
8
9
11
12
10

Castles Technology Co., Ltd. Pg. 8
2.2. Insert SAM Card
Step 1: Remove the back cover.
Step 2: Insert SAM card into the desired slot.
Step 3: Reverse the operation of step 1 to install the back cover.
Bottom: SAM 1
Upper: SAM 2

Castles Technology Co., Ltd. Pg. 9
2.3. Insert GSM SIM Card
Step 1: Remove the back cover.
Step 2: Insert SIM card into the desired slot.
Step 3: Reverse the operation of step 1 to install the back cover.
Bottom: SIM 1
Upper: SIM 2

Castles Technology Co., Ltd. Pg. 10
2.4. Insert Micro SD Card
Step 1: Remove the back cover.
Step 2: Place the Micro SD memory card.
Step 3: Reverse the operation of step 1 to install the back cover.

Castles Technology Co., Ltd. Pg. 11
3.Appendix
3.1. CB
⚫Warning:
Power cord shall be connected to a socket-outlet with earthing connection.
⚫Warning:
Risk of explosion if battery is replaced by an incorrect type. Dispose of expended
battery in accordance with local disposal regulations.
⚫Warning:
This product is intended to be supplied by a Listed Power Adapter "L.P.S." (Or
"Limited Power Source") and is rated at 12 Vdc, 1 A min., Tma = 40 degrees C.

Castles Technology Co., Ltd. Pg. 12
3.2. FCC
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
⚫Reorient or relocate the receiving antenna.
⚫Increase the separation between the equipment and receiver.
⚫Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
⚫Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
⚫Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
⚫This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Note: The country code selection is for non-US model only and is not available to all US
model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation
channels only.

Castles Technology Co., Ltd. Pg. 13
3.3. IC
Industry Canada statement
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne
doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage
reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Caution : (i) the device for operation in the band 5150-5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite systems.
Avertissement: les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés
uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with greater than 20cm
between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 20cm
entre le radiateur et votre corps.

Castles Technology Co., Ltd. Pg. 14
3.4. UL / IEC 62368-1
⚫Warning:
Power cord shall be connected to a socket-outlet with earthing connection.
⚫Warning:
Risk of explosion if battery is replaced by an incorrect type. Dispose of expended
battery in accordance with local disposal regulations.
⚫Warning:
This product is intended to be supplied by a Listed Power Adapter "L.P.S." (Or
"Limited Power Source") and is rated at 12 Vdc, 1 A min., Tma = 40 degrees C.
●Attention:
le cordon d'alimentation doit être branché sur une prise secteur avec mise à la
terre.
●Attention:
Risque d'explosion si la batterie est remplacée par une de type incorrect Éliminer
la pile usagée conformément à la réglementation locale en vigueur.
●Attention:
Le produit est destiné à être alimenté par un adaptateur secteur répertorié «
L.P.S. » (ou "Source d'alimentation limitée") et est évalué à 12 Vdc, 1 A min.,
Tma = 40 degrés C.
~ END ~