CATSKILL 51575 User manual

Assembly Instructions
Model 51575
Wide Cuisine Cart
GENERAL:
1. You have purchased model 51575.
2. Should you need assistance or need to replace a damaged or missing part simply give us a call M-F at
607-652-7321 from 7:30 am - 4:30 pm EST and we’ll send you the prepaid part via UPS usually that same
day! You may also email us [email protected].
3. Read the assembly instructions and the enclosed brochure before beginning assembly. Assembly is
easy if you read and follow the instructions step by step. See our website for assembly tips and videos.
4. Tools required: Phillips screwdrivers, medium and small; medium at blade screwdriver and a hammer.
5. Drawer glides are sometimes pre-packed with screws, these are not used.
6. Directions (left/right, front/back) are given as facing the front of an assembled upright unit.

TOPTOPTOP
CABINET PARTS 51575
Glide Support Sticks (2)
P/N: GLD SUP - 51575
Handle Side Panel (1)
P/N: SP/HDL - 51575
Plain Side Panel (1)
P/N: SP/PL - 51575
Shelf (2)
P/N: S - 51575 Back Panel (1)
P/N: BP - 51575
Cabinet Top (1)
P/N: TT - 51575
Door Spacer (1)
P/N: DORS - 11 15/16 - 51575
Drawer Bottom (1)
P/N: DBOT - 51575
Drawer Front (1)
P/N: DF - 51575
Drawer Back (1)
P/N: DBK - 51575
Drawer Side Left (1)
P/N: DS- 51575L
Drawer Side Right (1)
P/N: DS- 51575R
Left Door (1)
P/N: DOR - 51575L
Right Door (1)
P/N: DOR - 51575R
Top/Bottom Braces (2)
P/N: B - 51575 T/B Middle Front Brace (1)
P/N: B - 51575 MF
Not Used
Not Used

1 3/4” Phillips Flat Head Bolt (12)
1 1/4” Phillips Flat Head #8 Screw (12)
7/8” Truss Head Machine Screw (6)
3/4” Long 3/16” DIA. Steel Pin (6)
1” Long 3/16” DIA. Steel Pin (8)
1 1/2” Long 3/16” DIA. Steel Pin (4)
Caster Socket (4)
Cam (2)
5/8 Wooden Disk (12)
Nickel Handle (3)
Towel Bar Post (2)
Non-Locking Wheel Caster (2)
Locking Wheel Caster (2)
Magnet (1)
Polished
Nickel Towel
Bar (1)
3/16” Flat Washer (4)
10-24 Hex Nut (12)
CABINET HARDWARE 51575
5/8” Phillips Flat Head #8 Screw (2)
5/8” Pan Head Screw (2)
1/2” Phillips Flat
Head #4 Screw (1)
Magnet Plate (1)
Cam Posts (2)
(Used to attach
Drawer Front)
“L” Bracket (4)
14” Drawer Glide (1 Set )
Drawer
Cabinet
MAGNET PACK
5/8” Phillips Flat Head #7 Screw (12)
5/8” Phillips Flat Head #5 Screw (4)
(Used to attach “L” bracket
and cabinet glides)
(Used to attach drawer glides)
(Used to attach
Drawer Handles)
(Used to attach
Door Spacer)
(Door Pin)
(Shelf Pin)
(Brace Pin)

STEP 1
Glide Support Assembly
5/8” #7
1 1/4” #8 5/8” #7
5/8” #7
The glides look almost alike;
however, they are stamped
CR for cabinet right and CL
for cabinet left.
Left Side
Front
Right Side
Front
The “L” brackets are attached to the Glide Support using the large slot in the “L” bracket.
The Hole will be used to attach the table top.
Flush with back
Flush with back
Top of “L” Bracket should be even with the top of the glide support
Note: Glide holes sometimes change, just make
sure the cabinet glides are ush with the back
of the glide supports & pilot holes will line up -
only 2 holes are used!
Decide at this point if you want the handle/towel bar on the right or the left side of the cabinet as
side panels are interchangeable. At this point the metal glides will determine left side/right side once
installed.

STEP 3
A. Turn the side/back assembly (from
step 2) upside down (invert) on top of the
inverted table top.
B. Align the “L” brackets
with the 4 inside pilot holes in the table top
and secure with 5/8” #7 screws.
C. Tap two 1” pins into each side panel.
These pins will hold the bottom shelf.
STEP 2
A. Lay back panel at on a smooth surface with holes up.
B. We placed the handle/towel bar on the right for these instructions.
C. Attach side panels with 1 3/4” bolts and hex nuts. After inserting bolt(s) through the holes in the
side panels and through the holes in the long edges of the back panel, place a hex nut on the tip of
your nger, align nut with bolt and tighten.
D. Look ahead to step 3 which shows side panels
attached to back panel.
E. Attach towel bar with 1” Phillips Flat head screws/washer.
Use a washer to prevent the screw from pulling through the
side panel.
NOTE: Back panel is ush with bottom of side panels.
1 3/4” Machine Screw
Nut
1” Screw
Towel Bar
Towel Bar Post
1 3/4” Phillips Flat Head Bolt (8)
4 Used
in this step
10-24 Hex Nut (8)
4 Used
in this step
4 Used in this step
1” Long 3/16” DIA. Steel Pin
PIN
PIN
5/8” Phillips Head #7 Screw
4 Used in this step
4 Used in this step
1” Long 3/16” DIA. Steel Pin PIN
PIN
5/8” Phillips Head #7 Screw
4 Used in this step
1 3/4” Phillips Flat Head Bolt (8)
4 Used
in this step
10-24 Hex Nut (8)
4 Used
in this step

STEP 4
A. Attach the drawer back to the drawer sides with four
1 1/4” #8 screws. Make sure parts are aligned as in
illustration 4A.
B. Insert drawer bottom into the slots in the drawer
sides, best side to inside of drawer. Slide down until
seated in the slot in the drawer back. See illustration
4B.
C. Screw the cam posts into the two outside holes on
the inside face of the drawer front until seated. Only
3/8” of the post goes into the wood, leaving the 4
larger guide rings/head exposed. See illustration 4C.
D. Insert the posts into holes in the drawer sides until
seated against the front end of the drawer sides. Insert
cams so that slot in the cam ts over the post and
turn with Phillips screwdriver until seated. Don’t over-
torque! See illustration 4D.
E. Attach drawer handle with the two 7/8” Truss head
screws (no illustration).
F. Attach drawer glides to drawer sides using 5/8”
#5 screws. See illustration 4F
ILLUSTRATION 4A
ILLUSTRATION 4B
ILLUSTRATION 4D
ILLUSTRATION 4F
ILLUSTRATION 4C
Below line in wood
Cam Posts (2)
4 used
in this step
1 1/4” Phillips Flat Head #8 Screw
2 used
in this step
7/8” Truss Head Machine Screw
2 used
in this step
Cam
4 used
in this step
5/8” Phillips Flat Head #5 Screw

1 1/2” Pin 1/2” #4 Screw
7/8” Machine Screw
5/8” #8 Screw
Magnet Plate
Handle
STEP 5
Door Assembly
STEP 6
Brace Prep
3/4” Pin
Install 3/4” pins in brace ends

STEP 7
A. Take the top front brace (identical
to bottom front brace) holes in bottom
long edge up, insert the pins into the
slots on the inside of the front legs
and slide brace down until the holes in
the brace ends align with the holes in
the front legs. Secure brace with
1 3/4” bolts/hex nuts.
B. Take the middle front brace with
magnet block and slide brace into
place making sure magnet block
and holes for door pins are up as
illustrated. Secure with 1 3/4” bolts/
hex nuts.
STEP 8
A. Insert the pins in the door tops
into the holes in the middle front
brace as in Illustration 7. Place a
washer over the pins in the door
bottoms.
B. Take the bottom front brace,
insert brace as in step 7, making
sure the pins in the doors align
with the holes in the brace as in
Illustration 8. Secure with 1 3/4”
bolts/hex nuts.
1 3/4” Bolts
Nut
Insert brace pins here
Washer
Middle Front Brace
ILLUSTRATION 7
ILLUSTRATION 8

STEP 9
A. Stick magnet to magnet plate on right door.
B. With left door open, close the right door. The magnet should be positioned over the wooden block
on the bottom of the top front brace. Hold the magnet in place with your thumb, and open the right
door. The magnet will be in the correct position on the block. Mark your holes with a pencil.
C. Secure magnet with the two pan head screws in the magnet packet. Center screws in the slots in
the magnet . This will allow adjustment later, if needed.
NOTE: No pilot holes in block, as softwood!
D. Tap in the 12 wood disks into the side panels after making sure drawer and doors open/close
easily. Tighten all bolts.
Magnet
5/8” Pan Head Screw
2 Used
in this step
5/8” Wooden disk

STEP 10
Install Casters
A. Tap in caster sockets with a hammer until
teeth are in the wood. Don’t pound at or
wheels won’t enter. Locking casters usually
go on front - seat with sharp downward stroke
with hammer hitting the metal wheel frame.
STEP 11
A. Upright unit and insert drawer.
B. Insert pins for the middle shelf.
C. Place middle shelf on pins.
D. Place the back long edge of the
bottom shelf on the back pins. Lower
front of shelf. Close doors and shelf
will drop into place.

For continued beauty and long life of your
Catskill Craftsmen cart, we recommend
Catskill Craftsmen’s Butcher Block Oil.
Our Butcher Block Oil is available direct-
ly from Catskill Craftsmen’s factory. For
one eight ounce (8 . oz.) bottle, which
is sufcient for two applications, simply
send $6.95 along with the completed
coupon to the address below. Visit us
online at www.catskillcraftsmen.com to
browse our assortment of butcher block
care products. Visa and Mastercard are
accepted online .
Catskill Craftsmen, Inc.
15 West End Ave.
Stamford, NY 12167-1296
BUTCHER BLOCK OIL COUPON
Please send me______# of bottle(s) of the
Catskill Craftsmen Butcher Block Oil at $6.95
per bottle. My check or money order is
enclosed for a total of $____________.
Item code: 51575
Name_______________________________
Address _____________________________
City ________________________________
State ___________ Zip ________________
Please make checks payable to Catskill Craftsmen
Inc. 15 West End Ave., Stamford, NY 12167-1296