CATSKILL 1622 User manual

CRAFTSMEN, INC.
Assembly Instructions
Model 1622
Fold-A-Way Table
GENERAL: Your folding table has been engineered to fit together with a minimum of
effort if you follow the instructions step-by-step. Assembly should take about an hour.
The only tools you need are a medium Phillips screwdriver and a hard hammer. A flat
scrap of wood or plastic will come in handy to protect surfaces when hammering to seat
braces or disks. A power screwdriver will speed assembly, but is not necessary. A little
vegetable oil on the wood screw threads will make it easier to attach the feet to the table
ends/sides.
Read through the instructions completely to familiarize yourself with the various parts
and the progression of the assembly process. Inventory your parts against the parts list. If
anything is missing or damaged, contact us directly for prompt, free parts replacement.
Once your table is assembled, remember that it is made of solid northeastern hardwood
and will need to be cared for as outlined in the enclosed booklet, “All About Your Butcher
Block Unit.” Your table is designed to open either leaf individually or both leaves. When folded,
the unit takes up only 10” of outward space. Holes in the Table end/sides are hand holes
for easy movement of the 37 lb. unit. Casters are not practical on this unit as it would make
the unit top heavy if elevated on casters.
See our assembly video for this model on our website: www.catskillcraftsmen.com

(4) 3/4” Steel Pins
(4) 1 1/2” Steel Pins
(4) 1 3/4” Long #8 Wood Screws to Attach Feet
(6) Small Washers for Pivot Pins
(8) 2” Machine Screws (Bolts) for Basic Assembly
(8) Nuts for Machine Screws
PARTS LIST
(2) Factory Assembled Swing Legs (Identical)
(2) Drop Leaves (Identical)
(1) Top Support Brace for Main Frame (3” Wide)
(1) Bottom Support Brace for Main Frame (2” Wide)
(2) Feet for Main Frame (Identical)
(2) Table Ends/Sides (Identical)
(8) 5/8” Wooden Disks Fit in Holes
on Table Ends/Sides (Identical)

STEP 1
Tools needed: medium Phillips screwdriver
Hardware needed: (4) wood screws 1 3/4” #8
Parts needed: (2) Table Ends, (2) Feet
Preparation: dip screw tips in vegetable oil to
ease installation of screws into hardwood.
Invert Table ends (identical) and attach feet (identical) with
1 3/4” #8 screws as shown in illustration 1
Illustration 1
STEP 2
Illustration 2
Tools needed: medium Phillips screwdriver
Hardware needed: (4) 2” machine screws and (4) nuts
Parts needed: Table Ends with feet attached
and the bottom support brace
Join the leg assemblies at bottom
support brace using (2) machine
screws/nuts per side. Place
nut on finger tip, insert into
the nut access hole in the
brace, align with machine
screw and loosely tighten so that
frame stands alone.

STEP 3
Tools needed: Hammer
Hardware needed: (4) 3/4” Steel pins (shortest)
Parts needed: Frame from step 2,
and 2 swing legs (identical)
Insert/Tap (2) 3/4” steel pins into the short
vertical brace of each factory assembled
swing leg as in illustration 3.
DO NOT OVERDRIVE PINS! When seated,
pins should have 3/8” sticking out
of the brace ends.
NOTE: If pins are loose in the bottom of the swing legs, simply insert them in the top edge
of the bottom support brace in step 4
Illustration 3
STEP 4
Tools needed: None
Hardware needed: (2) washers
Parts needed: Basic Frame, Swing legs
Place one washer over each of the
bottom pins in the swing legs and insert
pins into the holes in the top edge of
the bottom support brace as shown
in illustration 4
Illustration 4
Washers

STEP 5
Tools needed: Hammer
Hardware needed: (4) 1 1/2” Steel pins (longest)
Parts needed: (2) Drop Leaves
Tap one 1 1/2” long pin into each end of both
drop leaves until seated. When seated, pin will
stick up about 3/4” out of the wood. CAUTION!
Don’t overdrive pins or wood will split!
OK if Pins are loose!
Illustration 5
STEP 6
Tools needed: None
Hardware needed: (4) washers
Parts needed: Basic assembly
plus 2 Drop Leaves
Gently spread the tops of the table
ends/sides apart and insert the drop
leaf pins (with one washer over each
pin) into the pre-drilled holes on the
top inside of the table ends/sides.
Place swing legs as shown in
illustration 6 to support the drop leaves.
Illustration 6

STEP 7
Tools needed: medium Phillips
screwdriver
Hardware needed: (4) 2” machine
screws (bolts) and (4) nuts
Parts needed: Basic assembly
plus top support brace
Take the top support brace with the 2
pin holes and 4 nut access holes (larger)
facing down and align the pin holes with
the pins on the top edges of the swing
legs.
NOTE: These pins do not get washers!
If necessary, tap down on the top of the
brace to seat the pins. CAUTION!
Hammer down on a scrap of flat
wood or plastic so as not to mar
the top surface of the brace.
When seated, secure brace with
machine screws/nuts as in illustration 7
Illustration 7
Illustration 8
STEP 8
Tools needed: medium
Phillips screwdriver, hammer
Hardware needed: (8) 5/8” wooden
disks (small)
TIP: Use a piece of heavy paper to
hammer on instead of directly on
wooden disks.
Tighten all machine screws/nuts.
Tap in (4) 5/8” disks into each table
end/side as shown in illustration 8.

For continued beauty and long life of
your Catskill Craftsmen cart, we
recommend Catskill Craftsmen’s Butcher
Block Oil.
If you would like to purchase Butcher
Block Oil directly from Catskill
Craftsmen’s factory, we offer a reduced
price. For one eight ounce (8 fl. oz.)
bottle, which is sufficient for two
applications, simply send $6.95 along
with the completed coupon to the
address below.
Catskill Craftsmen, Inc.
15 West End Ave.
Stamford, NY 12167-1296
CRAFTSMEN, INC.
BUTCHER BLOCK OIL COUPON
CRAFTSMEN, INC.
NAME _____________________________________
ADDRESS __________________________________
__________________________________________
CITY ______________________________________
STATE _________________________ ZIP _______
Please make checks payable to: Catskill Craftsmen Inc.
15 West End Ave. Stamford, NY 12167-1296
Please send me _____# of bottle(s) of the
Catskill Craftsmen Butcher Block Oil at $6.95.
My Check or Money Order is enclosed for a
total of $______________.
Item Code: 1622
012208