CDA SC050 User guide

1
SC050
Built-in pyrolytic oven
Use and maintenance

2| Instruction Manual
3 Important information
4 Appliance information
5 First use of the oven
6 Oven layout and
accessories
8 Control panel
8 Operation
10
11
11
11
Standby mode
Deep sleep
Setting the time
Changing the beep tone
11
12
14
15
16
17
Adjusting display
brightness
Minute minder
Setting and adjusting
the temperature
Heating functions
Timed operation
Pyrolytic cleaning
Contents
IMPORTANT: Please read the user instructions carefully before
using the appliance for the first time and before installing it.
Failure to install the oven, or to have it installed, as per the
instruction manual could invalidate the warranty. Any service
calls relating to misuse or incorrect installation could incur a
service charge.
18
19
Using the Airfry tray
Using the grill
19 ECO heating
20 Practical tips
21 Cleaning and
maintenance
27 Installation
29
30
Mains electrical
connection
Error Codes
31 Technical assistance
32 Specifications

Instruction Manual | 3
Important information
This appliance must only be used for the purpose for which it is intended,
i.e. domestic cooking. Any other use could be dangerous and may lead to
premature failure of the appliance.
The CDA Group Ltd. cannot be held responsible for injuries or losses
caused by incorrect use or installation of this product. Please note that CDA
reserves the right to invalidate the guarantee supplied with this product
following incorrect installation or misuse of the appliance.
Under no circumstances should any external covers be removed for
servicing or maintenance except by suitably qualified personnel.
User information
• The appliance and its accessible parts become hot during use
• Care should be taken to avoid touching heating elements
• The appliance can be used by children aged from 8 years and above.
Persons with reduced physical, sensory or mental capabilities must
be given instruction or supervision concerning safe operation of the
appliance and understand the hazards involved
• Do not allow anyone unfamiliar with the contents of this instruction
manual to operate the oven
• Do not use harsh cleaning agents or sharp metal objects to clean the
door as they can scratch the surface potentially resulting in cracking or
shattering of the glass
• Take care when opening the oven door during or after a cooking cycle
as hot steam may escape
• Do not use the oven in the event of a technical fault. Any faults must be
fixed by an appropriately qualified and authorised person
• In the event of an incident due to a technical fault, disconnect the power
and report the fault to CDA Customer Care
• The appliance has been designed only for cooking, any other use may
invalidate your warranty and cause danger
• Do not place anything weighing over 15kg on the opened oven door
18
19
Using the Airfry tray
Using the grill
19 ECO heating
20 Practical tips
21 Cleaning and
maintenance
27 Installation
29
30
Mains electrical
connection
Error Codes
31 Technical assistance
32 Specifications

4| Instruction Manual
Appliance information
Please enter the details on the appliance rating plate below for reference, to
assist CDA Customer Care in the event of a fault with your appliance and to
register your appliance for guarantee purposes.
Appliance Model
Serial Number
EU Declarations of Conformity:
This appliance has been manufactured to the strictest standards and
complies with all applicable legislation and the following European
Directives.
• The Low Voltage Directive 2014/35/EU
• Electromagnetic Compatibility Directive 2014/30/EU
• ErP Directive 2009/125/EU
The product has been marked with the symbol and the Declaration of
Conformity has been issued to the manufacturer and is available to the
competent authorities regulating the market
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2012/19/EU.
At the end of its working life, the product must be taken to a special local
authority waste collection centre or to a dealer providing appliance recycling
services.
Disposing of a household appliance separately avoids possible negative
consequences for the environment and health. It also enables the
constituent materials to be recovered, saving both energy and resources.
As a reminder of the need to dispose of household appliances separately,
the product is marked with a crossed-out wheeled dustbin .

Instruction Manual | 5
First use of the oven
In order to remove oil residues accumulated during the manufacturing
process and dust accumulated during storage and transport, we recommend
a preliminary cleaning before first use.
Preliminary heating
1. Remove any packaging elements from the oven cavity
2. Turn on ventilation or the extractor fan in the room or open a window
3. Set the oven to 250°C using the rapid preheating function
4. Allow to heat for approximately 30 minutes
5. Turn the oven o and allow to cool
6. To clean the oven use a damp cloth with warm water and a small amount
of washing up liquid
7. Dry with a clean cloth
A slightly unpleasant smell may be emitted during this process due to the
vaporising of oil residue used to protect the oven during storage.
Important! The time “0.00” will start flashing in the display
upon connection to the power supply.
The programmer should be set with the current time. (See Electronic
programmer ). If the current time is not set operation of the oven is not
possible.
The electronic prgrammer is equipped with touch sensors which are
switched on by touching or pressing the sensor surface for at least one
second.
Each sensor reaction is confirmed by the beep.
Keep the sensor surface clean at all times.

6| Instruction Manual
Oven layout and accessories
Side
racks
1
3
2
1. Oven function selector knob
2. Adjust settings knob
3. Electronic programmer

Instruction Manual | 7
Included accessories:
Baking tray Wire shelf
Grill rack Wire shelf
Airfry tray

8| Instruction Manual
Control panel
The control panel features an LED dis-
play and 3 buttons (touch sensors).
Set temperature
Clock setting
Minute minder
Note: You will hear a beep each time you touch a sensor.
It is not possible to turn o the acoustic beeps.
The meaning of the symbols on the display:
Temperature control dial End time
Minute minder Pyrolytic cleaning
Duration Child lock
Operation
The oven can be heated using the lower heater, upper heater, fan heater or
grill. Select the function using the function knob. The figure below shows the
functions located on the knob in their defined order:
position

Instruction Manual | 9
I
I
I
I
I
I
I
I
Adjust settings knob +/-
The adjust settings knob is a swivel type which does not rotate fully and
can only be turned slightly to the left or right. Use this knob to adjust
temperature and time. Turn slightly right to increase value. Turn slightly left
toward the “–” to decrease value. Use this knob to adjust temperature and
current time. If you keep the knob turned left or right from its default position
the rate of value changes will increase.
Turn on the power
When you connect the power supply (or power is restored after a power
outage) the appliance will prompt to set the current time, 0.00 will flash on
the display. Press the button (touch sensor) . Turn the +/– knob to adjust
the time. You must set the current time to use the appliance.
The function dial must be in position 0 to confirm the time setting. If the
function selector dial is in a dierent position, the indicator flashes and
the appliance waits until you turn the function selector dial to 0. Press the
button (touch sensor) to save the time and the appliance enters standby.
Note: In the event of a power outage, all settings such as Duration,
Temperature and Heating Function will be lost.
You will need to re-enter the settings to continue cooking.
If the pyrolytic cleaning is interrupted (or the door is locked for any other
reason – the is on), the oven will start the cooling and door opening
procedure before you can set the time.
If temperature above 80°C is detected in the oven, cooling fan is activated
and this does not aect the time adjustment process. Cooling fan turns o
when the temperature drops below 75°C.

10 | Instruction Manual
Standby mode
Switch the appliance to standby mode to reset all time, temperature and
timer settings. Heaters are disconnected. The display shows the current time
and has reduced brightness. Press the button (touch sensor) to adjust
the time, tone and brightness, and press the button (touch sensor) to
adjust the minute minder time setting.
If the temperature in the oven cavity exceeds 80°C, the current oven cavity
temperature is displayed (to indicate the residual heat) and the cooling fan
operates. When the temperature drops below 75°C, the cooling fan is turned
o and the current time is displayed instead of oven cavity temperature.
The appliance enters standby:
• Turn the function selector knob to position 0 at any time, you will hear a
beep
• After a power outage when set the current time
• After a timed programme completes (timed delayed operation, timed
operation, minute minder
• After activation of the Auto Shut-o Safety Device
• When you turn the knob to position 0 during a pyrolytic cleaning cycle,
the appliance activates cooling fan to unlock the door, and enters
standby only after the appliance has cooled down and the door is
unlocked
Activate the appliance from the standby mode:
Turn the knob from 0 to any available function to activate the appliance from
standby.
Note: if the appliance entered the standby mode automatically, you need
to first turn the knob to 0 and only then to another function. When the
appliance is in standby mode and the function knob is in a position other
than 0 - the indicator flashes.

Instruction Manual | 11
Deep sleep
If the appliance is unused for 10 minutes, it enters the deep sleep mode - the
sensors and the +/– settings knob are deactivated, and the only method of
activating the appliance is to turn the function knob from the “0” position to
any other position.
Setting the current time
You can set the current time in standby only. Press the button (touch
sensor) in this mode to display the current time with normal brightness. Use
the +/– knob to adjust the current time, wait 10 seconds to save the current
setting and the appliance will enter standby. Press the button (touch
sensor) to set the beep tone. The clock operates in 24h mode only.
Night Mode
During 22:00 – 06:00 in standby the display backlight is reduced as set for
night-time mode - 2 levels below the current setting.
Changing the beep tone
This function is available at any time in standby mode. When setting current
time, press the button (touch sensor) to display ton1 , where 1 is the
current beep tone – tones 1 through 3 are available. Turn the +/– knob to
change the current tone, then wait 5 seconds to confirm the new setting and
the appliance will enter the standby mode.
Adjusting the display brightness
This function is available at any time in standby mode. When selecting tone,
press the button (touch sensor) again to change display brightness and
bri4 (brightness 4) will be shown where 4 is the brightness level from 1 to 9.
Turn the +/– knob to change the brightness, then wait 5 seconds to confirm
the new setting and the appliance will enter the standby mode.

12 | Instruction Manual
Operation
You can use any baking or cleaning function available on the Function
Selector knob. Auto-o: When minute minder or any timed delayed, timed or
cleaning programme is completed, the appliance enters the standby mode
even if the function selector knob is set to 0.
Lighting
The appliance automatically controls oven light. By default the oven light is
on. The oven light is o:
• When 0, Pyrolytic cleaning or ECO is selected
• When the oven cavity temperature exceeds 300°C
• During pyrolytic cleaning and cooling
• Before and after the timed and timed delayed operation
• In standby mode, if the Function Selector knob is set to a position other
than 0
Cooling fan
Cooling fan operates independently of the set functions and the appliance
mode of operation. Cooling fan turns on when the oven cavity temperature
exceeds 80°C and turns o when it fall below is below 75°C.
Thermostat
The thermostat symbol indicates that the heating elements operate. If
any of the heating elements operates, the indicator lights up. The indicator
goes out, if none of the heating elements operates (e.g. when the oven
reaches the desired temperature and the heating elements are disconnected
until the temperature drops).
Minute Minder
Touch the button (touch sensor) in any mode to use minute minder.
Press to display countdown progress or 0.00 if minute minder is not
active, the indicator will flash.
Turn the +/– knob to adjust the Duration and press to confirm or simply
wait 5 seconds. When the minute minder is counting down, the indicator

Instruction Manual | 13
lights up on the display. When the countdown is complete you will hear a
beep, which you can mute by pressing any button (touch sensor).
The appliance will not enter standby until minute minder countdown is
completed and beeping alarm is acknowledged.
Oven door
Oven door must be closed during operation. Heating elements are
disconnected when you open the door. If the door is open for more than 60
seconds, you will hear an acoustic signal alerting you to an open door. Touch
any button (touch sensor) or close the door to silence the alarm. Opening
the door does not aect any temperature or time settings, however if the
door remains open for more than 10 minutes, the appliance cancels
all programmes.
Limit the operating time
For safety reasons, the oven operation is time limited. If the set temperature
is up to 100°C, the oven will enter the Standby mode after 10 hours, and
if the set temperature is 200°C or more, the oven operation is limited to
3 hours. In the temperature range of 101°C to 199°C, the operation time is
limited proportionally between 3 and 10 hours.
Activate a heating function
Turn the function selector knob from 0 to the desired position to activate
a heating function. When you set the Function Selector knob to a heating
function, the display will show the default temperature for a function, such as
170C.
The displayed temperature flashes (with reduced brightness) and the C
indicator lights up steadily. The value changes when you turn the function
selector knob. When you touch the sensor , the oven activates. After
10 minutes of inactivity, the oven deactivates. Press the button (touch
sensor) to set up timed delayed operation.

14 | Instruction Manual
Setting the temperature
When you have selected a heating function, use the +/– knob to adjust the
temperature. You can adjust the temperature in 5°C steps within the range
specified for each programme. Turn and hold the +/– knob for at least 1s
to adjust the temperature in 10°C steps. Press the button (touch sensor)
to confirm the new temperature setting or simply wait 5 seconds until the
appliance displays current time.
Turn the +/– setting knob display the following for 2 seconds:
• Left [–]: set temperature
• Right [+]: current oven cavity temperature
No setting is changed when the temperature is displayed.
Adjusting the temperature
Press the button (touch sensor) during oven operation to adjust the
temperature setting. The temperature flashes (with reduced brightness)
and the C indicator lights up steadily. Turn the +/– knob to adjust the
temperature. Press the button (touch sensor) to confirm the new
temperature setting or simply wait 5 seconds.
Changing the settings during cooking
You can change the function during cooking. If you turn the function knob
while modifying the temperature, the default temperature for the new
programme is displayed and the 5 second countdown restarts. If you turn
the function knob when the temperature is already set, the new programme
continues with the set temperature. If the newly selected programme has a
lower temperature range then the closest possible temperature is set.

Instruction Manual | 15
Table of heating functions
* Spit (if any)
Function description
Oven elements Temperature
[C] Default
temperature
[C]
Lighting
Top
heater
Grill
heater
Fan
heater
Bottom
heater
Fan
Min. Max.
Defrosting √ √ -- -- --
Quick oven pre-heat √ √ √ √ 30 280 170
Fan cooking √ √ 30 280 170
ECO √ √ 30 280 170
Pizza √ √ √ √ 30 280 220
Conventional √ √ √ 30 280 180
Pasty √ √ √ √ 30 280 170
Pyrolytic cleaning √ √ √ -- -- 480
Turbo grill * √ √ √ √ 30 280 190
Super grill * √√√ 30 280 250
Grill * √ √ 30 280 250
Lighting √-- -- --
O - - -

16 | Instruction Manual
Timed operation
Timed operation involves setting the duration after which the appliance
automatically turns o. You can set the duration from 1 minute to 23 hours
59 minutes. When the appliance is on or when you have turned the function
selector to a desired function press the (touch sensor) to set the
Duration. The indicator flashes and dur (duration) is displayed briefly for
1s and then 0.00 (or current countdown if the function is already active). Turn
the +/– to adjust the Duration and then press the button (touch sensor) to
confirm the setting or simply wait 5 seconds. The current time is displayed 5
seconds after you press the button (touch sensor).
The indicator is on during timed operation. The heating and temperature
functions can be freely modified during the time delayed operation.
To cancel timed operation set Duration to 0.00 and press the button (touch
sensor) or wait 5 s — the appliance will operate normally. Once duration has
elapsed, you will hear an [end] beep. All heating elements are disconnected.
You can silence the alarm as follows:
a) Do one of the following:
• press any button (touch sensor) except
• turn the function selector knob
• turn the +/– knob
• open the door
• This will clear all function and temperature settings. Even though the
Function Selector knob is set to a heating function, the appliance will
enter standby.
b) Turn the Function Selector knob to 0 - the appliance will enter standby.
c) Press the button (touch sensor) to set the new Duration and continue
cooking with currently set temperature and settings.
Note: in this case (when attempting to extend the Duration when the
beeping starts after the Duration has elapsed), setting the time to 0.00 turns
o the oven rather than allowing it to operate indefinitely.

Instruction Manual | 17
Delayed timed operation
You can set the appliance, so that its timed operation is delayed and cooking
ends at a specific time.
You must first set the Duration (same as in timed operation). Press the
button (touch sensor) to confirm Duration and end message will be
displayed briefly for 1s and then End Time will be display calculated as
Current Time + Duration + 1 minute. Turn the +/– knob to adjust the End Time.
Press the button (touch sensor) to confirm End Time or wait 5 s to cancel.
Once End Time is confirmed the and indicators light up steadily and
the Current Time is shown again.
The and indicators are on during the countdown to Start Time. The
symbol indicates when heating elements are on. Press to view and
modify the set duration.
Pressing the button once to set Duration, press again to set End Time and
press again to display the current time. Set Duration to 0.00 to cancel both
Duration and End Time and allow the appliance to operate indefinitely.
You can adjust End Time from (Current Time + Duration + 1 minute) to
(Current Time + Duration + 10 hours). You can modify Duration (when End
Time is set) from 0:00 to (Duration – Current Time – 1 minute).
When you have finished cooking, set the function selector knob to 0.
Pyrolytic cleaning
The P2.00 is flashing on the display and the indicator is on. Turn the +/–
knob to adjust the Duration to 2.00 - 2.30 - 3.00 hours.
Press or wait 20 s to start pyrolytic cleaning.
The Pyrolytic cleaning programme comes with special requirements. First,
the door status is checked. When the oven door is open, the indicator
flashes and the appliance waits 10 minutes until the oven door is closed and
if it is not, the pyrolytic programme is cancelled. When the door is closed the
indicator is on and the door is locked.

18 | Instruction Manual
The indicator is displayed and pyrolytic cleaning starts for 2.00 – 2.30 –
3.00 hours, depending on the Duration you have set.
The appliance displays duration time left until pyrolytic cleaning completes.
One hour before pyrolytic cleaning completes, the heaters are
disconnected, the temperature ---C is displayed and the appliance
starts cooling down. The door is unlocked when temperature is less than
150°C. The indicator is o when the door is unlocked. The pyrolytic
cleaning programme ends, but you cannot continue cooking.
No settings can be changed during the pyrolytic cleaning and you cannot
continue cooking with these settings, however you can view current settings
and temperature. When you silence the alarm, the appliance always enters
standby mode.
Note: The oven door is equipped with a lock, which prevents it from being
opened during the cleaning process. Do not open the door so as not to
interrupt the cleaning process. If there is a short power outage during
pyrolytic cleaning the appliance starts cooling down and eventually unlocks
the door.
If you interrupt the pyrolytic cleaning by turning the function selector knob
to another position (such as 0), the appliance starts cooling down and
eventually unlocks the door. When the door is unlocked the appliance
switches to standby. If during pyrolytic cleaning you open the door before
it is locked, there will be an [open door] beep and pyrolytic cleaning is
aborted. Before starting the pyrolytic cleaning, please see "Cleaning and
Maintenance."
Using the Airfry tray
Your oven comes with an Airfry tray. For best results, select the fan
cooking function ( ) and place the Airfry tray on the 3rd shelf rack with
a tray on a shelf below.

Instruction Manual | 19
Using the grill
In order to switch on the grill you need to:
• Set the Function Selector Control to the position marked grill.
• Preheat the oven for approx. 5 minutes (with the oven door closed).
For grilling with the function grill and super grill the temperature must be set
to 220ºC, but for the function fanned full grill it must be set to a maximum of
190ºC.
Warning! When using function grill it is recommended that the oven
door is closed. When the grill is in use accessible parts can become
hot. It is best to keep children away from the oven.
ECO heating
ECO heating is an optimised heating function designed to save energy when
preparing food. You cannot reduce the cooking time by setting a higher
temperature; preheating the oven is not recommended.
Do not change the temperature setting and do not open the oven door
during cooking.
Recommended settings for ECO heating
Type of dish Oven
function Temperature °C Level Time (min)
Sponge cake 180 - 200 2-3 50 -70
Muns 180 - 200 250 -70
Fish 190 - 210 2-3 45 - 60
Beef 200 - 220 290 - 120
Pork 200 - 220 290 - 160
Chicken 180 - 200 280 - 100

20 | Instruction Manual
Practical tips
The times given in the table below apply to any dish that is placed in to a
cold oven.
For a preheated oven the times should be reduced by 5 - 10 minutes.
The figures given below are approximate and can be altered based on your
own experience and cooking preferences.
1) Preheat
2) Baking smaller items
Type of dish Heating Function Level Time [Min] Temperature [°C]
Sponge cake 2 - 3 30 - 50 160 - 200
Muns 3 25 - 40
2)
160 - 170
1)
Muns 3 25 - 40
2)
155 - 170
1)
Pizza 2 - 3 15 - 25 200 - 230
1)
Fish 2 45 - 60 210 - 220
Fish 2 - 3 45 - 60 160 - 180
Fish 2 - 3 60 -70 190
Sausages 4 14 - 18 220
Beef 2 120 - 150 225 - 250
Beef 2 120 - 160 160 - 180
Pork 2 90 - 120 160 - 230
Pork 2 90 - 120 160 - 190
Chicken 2 70 - 90 180 - 190
Chicken 2 45 - 60 160 - 180
Chicken 2 60 - 70 175 - 190
Vegetables 2 40 - 50 190 - 210
Vegetables 3 40 - 50 170 - 190