CEECO SSP-350-X-130 User manual

SSP-350-X-130-ISSUE4.0
SERVICE MANUAL
FOR
MODEL SSP-350-X-130
Wall Mount
PRISON VISITATION TELEPHONE WITH FUNCTIONAL
MAGNETIC HOOKSWITCH, RINGER AND INDICATOR
Serving the Telephone Industry Since 1930
Communication Equipment 519 West South Park Street
& Engineering Company Okeechobee, FL. 34972
Voice: 863-357-0798
Fax: [phone]

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
2
IMPORTANT INFORMATION
FOR
CUSTOMER
Please fill in before you continue.
The following information is necessary when calling CEECO for assistance.
MODEL NUMBER
MODEL SSP-350-X-130 PRISON
VISITATION TELEPHONE.
SERIAL NUMBER
DATE MANUFACTURED
LOCATION INSTALLED
For us to better serve you, please have this information available when calling for
technical support.
CEECO
Communication Equipment & Engineering Company
519 West South Park Street
Okeechobee, FL. 34972
[phone] Voice
[phone] Fax

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
3
TABLE OF CONTENTS
SECTION PAGE
1.0 INTRODUCTION................................................................................................... 4
2.0 GENERAL DESCRIPTION.................................................................................. 4
3.0 OPERATION .......................................................................................................... 4
4.0 RECOMMENDED TOOLS AND TEST EQUIPMENT.................................... 4
5.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS..................... 5
6.0 TESTING................................................................................................................. 6
7.0 SPECIFICATIONS................................................................................................. 6
8.0 PARTS LIST ........................................................................................................... 7
9.0 REPAIR AND RETURN INFORMATION......................................................... 8
10.0 WARRANTY POLICY.......................................................................................... 9

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
4
1.0 INTRODUCTION
The practices in this manual provide installation and maintenance information for
Model SSP-350-X-130 Stainless Steel Panel Visitation Phone.
The information in this manual is subject to change without notification.
For information not included in this manual, please call or write:
CEECO
Customer Service
519 West South Park Street
[phone]
[phone] FAX
2.0 GENERAL DESCRIPTION
The CEECO Model SSP-350-X-130 is a Ring-Down Telephone designed for
special-purpose applications that require a Vandal Resistant yet attractive
telephone. The SSP-350-X-130 has a functional hookswitch that allows “on” and
“off” hook conditions. It includes an electronic ringer and ring indicator lamp to
aide in the recognition of inbound calls. It is intended to be used on a ring down
line or circuit and may be used in both fixed and mobile applications.
3.0 OPERATION
Lift the handset and the off hook condition will trigger the ring down line or
circuit. If on the receiving end of the call, the ringer will sound and the lamp will
illuminate with the inbound ring. When the second handset is lifted a normal
conversation will follow. Upon completion of call return handsets to the cradles.
4.0 RECOMMENDED TOOLS AND TEST EQUIPMENT
Volt/Ohm Meter
1/4" Nut Driver
Flat Blade Screw Driver
Security Tool, CEECO Part Number 301-064 (sold separately)

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
5
5.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS
5.1 These SSP-350-X-130 units are intended to be used with the CEECO
optional QLink ring down unit. However, they may be connected to a
Central Office or PBX ring down line. The CEECO QLink ring down unit
requires 110-120 VAC. *Grounding and installation must be in
accordance with all applicable local and national electrical and
building codes.
5.2 Determine the desired and safe mounting location for the QLink device.
Do not plug it into the AC power until the total installation of the
visitation units is completed.
5.3 The SSP-350-X-130 is designed to be on a vertical surface. A longer line
cord may be substituted if necessary. Route the cord as required and
utilize the appropriate conduit hole on the mounting box. Plug the
remaining holes with the supplied conduit plugs. Install the mounting
boxes as desired.
NOTE: Modular line cords may be substituted with simply wire pairs of
22-26 gauge stranded wire. Spade lugs may be required.
5.4 Run the modular cords or wires through the selected conduit hole in the
mounting box. Mount the panel telephone unit, utilizing the security
screws provided, to the mounting box. The security tool, which is sold
separately, must be used for the security screws.
5.5 Attach the modular cords or wires, as appropriate, to the QLink or other
ring down line. The phone units plugged into the same Qlink or attached
to the same ring down line will allow talk paths to one another. Plug the
QLink into the AC power or activate ring down line and the units will be
ready for use.
5.6 For mobile use a standard DC to AC power inverter may be required if
24VDC is not available.
***** WARNING *****
A. Never install telephone wiring during a lightning storm.
B. Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
C. Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
D. Use caution when installing or modifying telephone lines.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
6
6.0 TESTING
6.1 Lift the handset of one of the units that are intended to talk to one another.
The receiving unit should sound the ringer and the lamp should light. Lift
the handset of the receiving unit and determine that normal conversation is
allowed. If so, return the handsets to the cradles. The phone units are
ready for use. If this is a single, ring down unit connected to a C.O. or
PBX line, the call should be automatically placed or connected, when the
handset is lifted.
6.2 If normal conversation does not take place, please review the installation
steps. Make a visual check to ensure that all wires and connectors are as
they should be. Remember that the phone units, which are connected to
the same QLink or ring down line will allow talk paths to one another.
6.3 Once it has been determined that the installation and connections are
correct, and if trouble is still experienced, please refer to section 9.2 of this
manual.
7.0 SPECIFICATIONS
INPUT POWER: QLink or Central Office or PBX
LOOP CURRENT: 23 ma min. to 80 ma max.
IMPEDANCE: 600 ohms
HEARING AID
COMPATIBLE: Meets EIA standards
ENVIRONMENTAL: Temperature 0° C to 50° C
Humidity 20%-90% non-condensating
TELEPHONE COVER: Brushed 16 ga. Stainless Steel
DIMENSIONS: 4.5" Wide x 4.5" High x 5.0" Deep
(Handset On-hook)
MOUNTING: Standard double switch electrical box
WEIGHT: Approximately 3 lb.
FCC REGISTRATION: BW-88T7-13716-TE-T

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
7
8.0 PARTS LIST
QUANTITY PART NUMBER DESCRIPTION
1 301-591 Hookswitch Cradle
1 301-004-32 Handset with Armored Cord
1 301-009 Network
1 301-018 2.5’ Line Cord
1 301-005 Armored Cable Ferrule
4 301-9054 Security Screw
(4 screws are needed per unit)
OPTIONS:
1 301-064 Security Tool (for screw above)
1 301-14207 Mounting Box
1 QLink Ring Down Module
1 Misc DC to AC power inverter

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
8
9.0 REPAIR AND RETURN INFORMATION
9.1 WARRANTY REPAIR
Any device returned requiring warranty service; repair or credit must be
accompanied with a "Return Material Authorization" (RMA) Form. It
must include: return-shipping instructions, original purchase order
number and special marking instruction. A description of the trouble
observed must be attached to the defective unit. This information must be
inside the shipping container.
9.2 DIRECT ALL INQUIRES TO:
CEECO
Repair Department
519 West South Park Street
Okeechobee, FL. 34972
[phone]
9.3 NON-WARRANTY REPAIR
CEECO will repair equipment out of warranty for a set charge plus parts.
The customer must pay the shipping costs both directions.
9.4 RETURN FOR CREDIT
Material may be returned for credit only with prior approval. Material
authorized for return is subject to a 20% restocking charge based on the
manufacturer's list price. Return RMA must be requested no later than 30
days after original shipment.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
9
10.0 WARRANTY POLICY
10.1 GENERAL
CEECO products are guaranteed to be free of defects in material and
workmanship for a period of 365 days from the date of original purchase.
CEECO's obligation under this warranty is limited to repair or
replacement of any part found to be defective by CEECO. Under no
circumstances shall CEECO be liable for loss, damage, and cost of repair
or consequential damages of any kind, which has been caused by neglect,
abuse, acts of God or improper operation of equipment. This warranty is
limited to the value of material only.
10.2 PRINTED CIRCUIT BOARDS
Printed circuit boards should not be field repaired. If a unit is found to be
faulty, replace it with another unit and return the faulty unit to CEECO for
repair. Modifications by any one other than CEECO will void the
warranty.