CEECO SSP-361-X User manual

SSP-361-X-ISSUE4.0
SERVICE MANUAL
FOR
MODEL SSP-361-X
STAINLESS STEEL PANEL
TELEPHONE
FOR MANUAL RING-DOWN
OPERATION
Serving the Telephone Industry Since 1930
Communication Equipment 519 W South Park Street
& Engineering Company Okeechobee, FL 34972
Voice: 863-357-0798
Fax: [phone]

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
2
IMPORTANT INFORMATION
FOR
CUSTOMER
Please fill in before you continue.
The following information is necessary when calling CEECO for assistance.
MODEL NUMBER MODEL SSP-361-X, FOR RING-DOWN
APPLICATIONS
SERIAL NUMBER
DATE MANUFACTURED
LOCATION INSTALLED
For us to better serve you, please have this information available when calling for
technical support.
CEECO
Communication Equipment & Engineering Company
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
3
TABLE OF CONTENTS
SECTION PAGE
1.0 INTRODUCTION................................................................................................... 4
2.0 GENERAL DESCRIPTION.................................................................................. 4
3.0 OPERATION .......................................................................................................... 4
4.0 RECOMMENDED TOOLS AND TEST EQUIPMENT .................................... 4
5.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS ..................... 5
6.0 TESTING................................................................................................................. 6
7.0 SPECIFICATIONS................................................................................................. 7
8.0 PARTS LIST ........................................................................................................... 8
9.0 FCC NOTICE.......................................................................................................... 9
10.0 REPAIR AND RETURN INFORMATION....................................................... 10
11.0 WARRANTY POLICY ........................................................................................ 11

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
4
1.0 INTRODUCTION
The practices in this manual provide installation and maintenance information for
Model SSP-361-X Stainless Steel Panel Telephone.
The information in this manual is subject to change without notification.
For information not included in this manual, please call or write:
CEECO
Customer Service
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net
2.0 GENERAL DESCRIPTION
The CEECO Model SSP-361-X is a Stainless Steel Panel Telephone designed for
ring-down circuit applications. The telephone is constructed of stainless steel
with a brushed finish, making it both sturdy and attractive. An armored cord,
hearing aide-compatible handset is standard. The telephone is designed for the
panel to mount flush with the mounting surface. The panel measures
approximately 13 1/8” H x 10 1/8” W. The mounting box (sold separately)
mounts in the recess of a wall and measures approximately 11 ½” H x 8 ½” W x 2
5/8” D. As a standalone item, the telephone can only receive incoming calls. It
must be mated with external dialing equipment, in order to initiate calls.
3.0 OPERATION
The audible ringer signals an incoming call. When the handset is lifted, the call is
connected and normal telephone operation will follow. If external call equipment
is utilized, a number can be dialed when the handset is lifted. When the other
party answers the call is connected and normal telephone operation will follow.
4.0 RECOMMENDED TOOLS AND TEST EQUIPMENT
Volt/Ohm Meter
¼” Nut Driver
Flat Blade Screw Driver
Security Tool, CEECO P/N 301-037 (Sold Separately)

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
5
5.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS
5.1 Using a 301-037 security tool (sold separately), remove the security
screws.
5.2 The security tool is for a standard 5/32" button head screw generally used
on the framework of the phone booths.
5.3 Separate the panel from the mounting box.
5.4 The mounting box is designed to be mounted flush with a flat vertical
surface. Mounting holes are provided on all sides and the back of the box.
5.5 Run the inside station wire through the mounting box and terminate the
Tip and Ring wires to the green and red wires of the RJ11C terminal
block, located inside the box.
5.6 The use of a gas tube station protector is recommended. The station
ground should not exceed 50 ohms.
5.7 Plug the modular line cord from the panel assembly into the RJ11C
terminal block.
5.8 Dress the line cable away from the mounting holes before installing the
panel onto the mounting box.
*****WARNING*****
A. Never install telephone wiring during a lightning storm.
B. Never touch uninsulated telephone wires or terminals unless
the telephone line has been disconnected from the network
interface.
C. Never install telephone jacks in wet locations unless the jack
is specifically designed for wet locations.
D. Use caution when installing or modifying telephone lines.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
6
6.0 TESTING
6.1 Connect the telephone to the intended line.
6.2 From another telephone or test set, call the SSP-361-X telephone.
6.3 Verify that the ringer is working and answer the phone.
6.4 Normal telephone operation should be allowed.
6.5 Hang up the telephone. It is now ready for operation.
6.6 If the telephone is being utilized in connection with external call
equipment, lift the handset.
6.7 Verify that the intended number dials out on the line.
6.8 When the call is answered, normal telephone operation should follow.
6.9 Hang up the telephone. It is now ready for operation.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
7
7.0 SPECIFICATIONS
INPUT POWER: C.O. Line Powered
LOOP CURRENT: 23ma min to 80ma max
IMPEDANCE: 600 ohms
HEARING AID
COMPATIBLE: Meets EIA standards
ENVIRONMENTAL: Temperature 0°C to 50°C
Humidity 20%-90%
FACEPLATE: Brushed 14 gauge Stainless Steel
MOUNTING: Apparatus Box
DIMENSIONS: 10.12” W x 13.12” H
WEIGHT: 8 lb.
FCC REGISTRATION: BW88T7-13716-TE-T
UL LISTED NO.: 6OF5
RINGER EQUIVALENCY: 0.4A
TYPE JACK: RJ11C

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
8
8.0 PARTS LIST
QUANTITY PART NUMBER DESCRIPTION
1 301-004 Handset with Armored Cord
1 401-009 Ringer
1 301-009 Network
1 301-588 Hookswitch Cradle
1 301-581 Tongue and Bracket Assembly
2 301-570 Microswitch Assembly
1 301-018 Modular Cord
1 301-054 Modular Jack
1 361-001 Apparatus Box
6 406-019 Security Screw 10-32 x 1/2”
ACCESSORIES:
1 301- 037 Security Tool

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
9
9.0 FCC NOTICE
9.1 FCC REGISTRATION AND REPAIR INFORMATION
Your new telephone has been registered with the Federal Communication
Commission (FCC) in accordance with Part 68 of its rules. The FCC
requires that you be advised of certain requirements involving the use of
this telephone.
9.2 CONNECTION WITH THE NATIONWIDE TELEPHONE NETWORK
The FCC requires that you connect this telephone to the Nationwide
Telephone Network through a registered jack provided by the Telephone
Company in your area. This jack is a modular outlet, which you can order
from your local telephone company.
9.3 NOTIFICATION TO THE TELEPHONE COMPANY
Before connecting this telephone, the FCC requires that you notify your
local telephone company business office. The number is in the front of
your phone book.
Tell them: The "line" to which you will connect the telephone (that is,
your phone number) and the telephone's FCC registration number and
ringer equivalence number. These numbers are listed in Section 7.0.
The FCC further requires that you notify your local telephone company
when permanently disconnecting this telephone.

ISSUE 4.0
CEECO
Communication Equipment & Engineering Company
PROPRIETARY
1
0
10.0 REPAIR AND RETURN INFORMATION
10.1 WARRANTY REPAIR
Any device returned requiring warranty service, repair or credit must be
accompanied with a "Return Material Authorization" (RMA) Form. It
must include: return shipping instructions, original purchase order number
and special marking instruction. A description of the trouble observed
must be attached to the defective unit. This information must be inside the
shipping container.
10.2 DIRECT ALL INQUIRES TO:
CEECO
Repair Department
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net
10.3 NON-WARRANTY REPAIR
CEECO will repair equipment out of warranty for a set charge plus parts.
The customer must pay the shipping costs both directions.
10.4 RETURN FOR CREDIT
Material may be returned for credit only with prior approval. Material
authorized for return is subject to a 20% restocking charge based on the
manufacturer’s list price. Return Material Authorization must be
requested no later than 30 days after original shipment.