CEECO SSP 361-D User manual

Issue 4.0
MODEL SSP 361-D
STAINLESS STEEL PANEL
TELEPHONE
Equipped with ATD11 Board
SERVICE MANUAL
R
IMPORTANT INFORMATION
COMMUNICATION EQUIPMENT AND ENGINEERING COMPANY
519 W South Park Street Okeechobee, FL 34972
863-357-0798 telephone
Serving The Telephone Industry Since 1930.

Issue 4.0
CEECO
Communication Equipment and Engineering Company
PROPRIETARY
2
FOR
CUSTOMER
Please fill in before you continue.
The following information is necessary when calling CEECO for assistance.
MODEL NUMBER MODEL SSP-361-D EQUIPPED WITH
ATD11 BOARD
SERIAL NUMBER
DATE MANUFACTURED
LOCATION INSTALLED
For us to better serve you, please have this information available when calling for technical
support.
CEECO
Communication Equipment and Engineering Company
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net

Issue 4.0
CEECO
Communication Equipment and Engineering Company
PROPRIETARY
3
TABLE OF CONTENTS
SECTION PAGE
1.0 GENERAL DESCRIPTION .............................................................................................. 5
2.0 PROGRAMMING .............................................................................................................. 5
3.0 OPERATION ...................................................................................................................... 6
4.0 RECOMMENDED TOOLS AND TEST EQUIPMENT ................................................ 6
5.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS ................................. 6
6.0 TESTING............................................................................................................................. 7
7.0 TROUBLESHOOTING ..................................................................................................... 8
8.0 SPECIFICATIONS............................................................................................................. 9
9.0 PARTS LIST ..................................................................................................................... 10
10.0 FCC NOTICE.................................................................................................................... 11
11.0 REPAIR AND RETURN INFORMATION ................................................................... 12
12.0 WARRANTY POLICY .................................................................................................... 13

Issue 4.0
CEECO
Communication Equipment and Engineering Company
PROPRIETARY
4
INTRODUCTION
The practices in this manual provide installation and maintenance information for
Model SSP-361-D Stainless Steel Panel Telephone.
The information in this manual is subject to change without notification.
For information not included in this manual, please call or write:
CEECO
Customer Service
519 W South Park Street
Okeechobee, FL 34972
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net

Issue 4.0
CEECO
Communication Equipment and Engineering Company
PROPRIETARY
5
1.0 GENERAL DESCRIPTION
The CEECO Model SSP-361-D is a Stainless Steel Panel Telephone designed for special purpose
applications where a telephone must be both sturdy and attractive. It is equipped with an ATD-11A
automatic tone dialer that will dial a single number of up to eleven (11) digits. The automatic dialing
feature is activated when the handset is lifted (“off hook” condition).
The SSP-361-D is not designed for incoming calls, but may still receive them. If a call is placed to the
phone, the automatic dialer will still dial its number when the receiver is lifted off hook.
2.0 PROGRAMMING
NOTE: It is recommended that you ground yourself to prevent ESD damage to the
PCB(s).
2.1 If the number to be programmed is a (1+) call, position the J1 green mini-jumper
on the "1+" position, which will cause the digit "1" to be dialed in front of the
other digits. If the number to be programmed is a local call, position the J1 green
mini-jumper on the "B" position, which is also the farthest right position. If you
have difficulty locating the J1 green mini-jumper, it is the first jumper position
you will see just below the right hand corner of the A-K main matrix board,
which contains ten green mini-jumpers.
2.2 If a 3 digit area code is to be dialed, position the J3 green mini-jumper on the "11"
position. If the number being dialed is within the same area code, position the J3
green mini-jumper on the "8" position. The J3 green mini-jumper is located just
below the J1 jumper. It is the second green mini-jumper you will see below the
right hand corner of the A-K main matrix board.
2.2 Set each of the 10 green mini-jumpers on the A-K main matrix board to
correspond to the 10 digits of the number to be dialed. The last 3 digits will be
ignored if the J3 jumper is on "8".
2.4 Be sure each green mini-jumper is properly positioned to make good contact and
dial the intended number.
2.5 Temporarily remove the J2 jumper. As accurately as possible, measure the time
delay between the moment the handset is lifted and the moment the phone
receives dial tone. Try it several times. If this time is consistently 1 second or
less, position the J2 jumper on the "1" position to set the delay before dialing to 1
1/2 to 2 seconds. Otherwise position the J2 jumper on the "3" position to set the
delay before dialing to 3 to 4 seconds. The J2 mini-jumper is the lone green
mini-jumper located farthest from the right hand corner of the A-K main matrix
board.

Issue 4.0
CEECO
Communication Equipment and Engineering Company
PROPRIETARY
6
3.0 OPERATION
Lift the handset. After a delay for dial tone, the programmed number will be dialed
automatically and a normal phone conversation may take place.
4.0 RECOMMENDED TOOLS AND TEST EQUIPMENT
Volt/Ohm Meter
1/4" Nut Driver
Flat Blade Screw Driver
Security Tool, CEECO Part Number 301-037
5.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS
5.1 Using a 301-037 security tool (sold separately), remove the security screws.
5.2 The security tool is for a standard 5/32" button head screw generally used on the
framework of the phone booths.
5.3 Separate the panel from the mounting box.
5.4 The mounting box is designed to be mounted flush with a flat vertical surface.
Mounting holes are provided on all sides and the back of the box.
5.5 Run the inside station wire through the mounting box and terminate the Tip and
Ring wires to the green and red wires of the RJ11C terminal block, located inside
the box.
5.6 The use of a gas tube station protector is recommended. The station ground
should not exceed 50 ohms.
5.7 Plug the modular line cord from the panel assembly into the RJ11C terminal
block.
5.8 Dress the line cable away from the mounting holes before installing the panel
onto the mounting box.
*****WARNING*****
A. Never install telephone wiring during a lightning storm.
B. Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected from the network interface.
C. Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
D. Use caution when installing or modifying telephone lines.

Issue 4.0
CEECO
Communication Equipment and Engineering Company
PROPRIETARY
7
6.0 TESTING
6.1 Program the phone according to section 2.0
6.2 Lift the handset. Phone waits one and one half to four seconds (depending on the
position of J2 per Section 2.05). The programmed number is automatically dialed.
6.3 The transmitter is muted while the phone is dialing.
6.4 Incoming calls are not recommended but if a call is placed to the phone and the
handset is lifted there is a one and one half to four second delay (depending on the
position of J2. Section 2.05), the programmed number is dialed, and then a normal
phone conversation can take place.

Issue 4.0
CEECO
Communication Equipment and Engineering Company
PROPRIETARY
8
7.0 TROUBLESHOOTING
Always visually check the phone for loose or shorted wires, damaged terminals or
damaged parts.
PROBLEM: NO DIAL TONE
POSSIBLE CAUSE:
LINE CORD
CONNECTOR
RJ11C CONNECTOR
NETWORK
HANDSET
ATD-11A BOARD
PROBLEM: DIAL TONE IS DISTORTED
POSSIBLE CAUSE:
NETWORK
HANDSET
PROBLEM: TRANSMITTER DOES NOT TURN ON
POSSIBLE CAUSE:
HANDSET
NETWORK
PROBLEM: PHONE DOESN'T DIAL PROGRAMMED NUMBER
POSSIBLE CAUSE:
ATD-11A BOARD
PROGRAMMING SWITCH MATRIX SET WRONG
JUMPER IN WRONG POSITION
PROBLEM: RINGER DOES NOT OPERATE
POSSIBLE CAUSE:
RINGER
NETWORK

Issue 4.0
CEECO
Communication Equipment and Engineering Company
PROPRIETARY
9
8.0 SPECIFICATIONS
INPUT POWER: C.O. Line Powered
LOOP CURRENT: 23ma min to 80ma max
IMPEDANCE: 600 ohms
HEARING AID
COMPATIBLE: Meets EIA standards
ENVIRONMENTAL: Temperature 0°C to 50°C
Humidity 20%-90%
FACEPLATE: Brushed 14 gauge Stainless Steel
MOUNTING: Apparatus Box
DIMENSIONS: 10.12” W x 13.12” H
WEIGHT: 8 lb.
FCC REGISTRATION: BW88T7-13716-TE-T
UL LISTED NO.: 6OF5
RINGER EQUIVALENCY: 0.4A
TYPEJACK: RJ11C

Issue 4.0
CEECO
Communication Equipment and Engineering Company
PROPRIETARY
10
9.0 PARTS LIST
QUANTITY PART NUMBER DESCRIPTION
1 350-130 ATD-11A Automatic Tone Dial
1 301-004 Handset with Armored Cord
1 401-009 Ringer
1 301-009 Network
1 301-588 Hookswitch Cradle
1 301-581 Tongue and Bracket Assembly
2 301-570 Microswitch Assembly
1 301-018 Modular Cord
1 301-054 Modular Jack
1 361-001 Apparatus Box
6 406-019 Security Screw 10-32 x 1/2”
ACCESSORIES:
1 301- 037 Security Tool

Issue 4.0
CEECO
Communication Equipment and Engineering Company
PROPRIETARY
11
10.0 FCC NOTICE
10.1 FCC REGISTRATION AND REPAIR INFORMATION
Your new telephone has been registered with the Federal Communication
Commission (FCC) in accordance with Part 68 of its rules. The FCC requires that
you be advised of certain requirements involving the use of this telephone.
10.2 CONNECTION WITH THE NATIONWIDE TELEPHONE NETWORK
The FCC requires that you connect this telephone to the Nationwide Telephone
Network through a registered jack provided by the telephone company in your
area. This jack is a modular outlet which you can order from your local telephone
company.
10.3 NOTIFICATION TO THE TELEPHONE COMPANY
Before connecting this telephone, the FCC requires that you notify your local
telephone company business office. The number is in the front of your phone
book.
Tell them: The "line" to which you will connect the telephone (that is, your
phone number) and the telephone's FCC registration number and ringer
equivalence number. These numbers are listed in Section 7.0.
The FCC further requires that you notify your local telephone company when
permanently disconnecting this telephone.

Issue 4.0
CEECO
Communication Equipment and Engineering Company
PROPRIETARY
12
11.0 REPAIR AND RETURN INFORMATION
11.1 WARRANTY REPAIR
Any device returned requiring warranty service, repair or credit must be
accompanied with a "Return Material Authorization" (RMA) Form. It must
include: return shipping instructions, original purchase order number and special
marking instruction. A description of the trouble observed must be attached to
the defective unit. This information must be inside the shipping container.
11.2 DIRECT ALL INQUIRES TO:
CEECO
Repair Department
863-357-0798- telephone
863-357-0006- facsimile
[email protected]
www.ceeco.net
11.3 NON-WARRANTY REPAIR
CEECO will repair equipment out of warranty for a set charge plus parts. The
customer must pay the shipping costs both directions.
11.4 RETURN FOR CREDIT
Material may be returned for credit only with prior approval. Material authorized
for return is subject to a 20% restocking charge based on the manufacturers list
price. Return Material Authorization must be requested no later than 30 days
after original shipment.

Issue 4.0
CEECO
Communication Equipment and Engineering Company
PROPRIETARY
13
12.0 WARRANTY POLICY
12.1 GENERAL
CEECO products are guaranteed to be free of defects in material and
workmanship for a period of 365 days from the date of original purchase.
CEECO's obligation under this warranty is limited to repair or replacement of any
part found to be defective by CEECO. Under no circumstances shall CEECO be
liable for loss, damage, cost of repair or consequential damages of any kind which
have been caused by neglect, abuse, act of God or improper operation of
equipment. This warranty is limited to the value of material only.
12.2 PRINTED CIRCUIT BOARDS
Printed circuit boards should not be repaired in the field. If a unit is found to be
faulty, replace it with another unit and return the faulty unit to CEECO for repair.
Modifications by anyone other than CEECO will void the warranty.