Celexon DELUXX 1000004533 User manual

Thank you for choosing a quality DELUXX product. Please read this
manual carefully before using the screen and keep it in a safe place.
User manual
DELUXX Cinema Electric Screen (Tension)

1
Safety instructions
Please read the enclosed data sheet with further safety and usage instructions
before installation.
Do not start assembly before completely reading and understanding the manual.
This product should only be installed by qualied personnel with mechanical and
electrical know-how.
Carry out the installation with another person to ensure safe installation.
Tighten the screws, but do not overtighten them as over tightening may cause
damage and aect the secure hold of the screen.
This product is intended for indoor use. Outdoor use could damage the product.
DE:
Auf http://www.deluxx.com/downloads nden Sie die aktuelle Version dieser
Bedienungsanleitung zum Download.
EN:
Please visit http://www.deluxx.com/downloads for the latest version of this
manual.
FR:
Veuillez visiter http://www.deluxx.com/downloads pour obtenir la dernière
version du manuel d‘utilisation.
NL:
Op http://www.deluxx.com/downloads vindt u de meest actuele download
versie van de bedieningshandleiding.
SE:
Under http://www.deluxx.com/downloads hittar du och kan ladda ner den
aktuella versionen av din bruksanvisning.
PL:
Na stronie http://www.deluxx.com/downloads znajdą Państwo aktualną wersję
instrukcji obsługi.
ES:
Visite http://www.deluxx.com/downloads para obtener la última versión de este
manual.
IT:
La versione aggiornata del manuale d´istruzioni è presente alla pagina
http://www.deluxx.com/downloads.

2
Safety instructions
Hanging loads must be tested at least twice a year for strength and load-bearing
capacity.
Use the product and all accessories only as intended.
Children should not use the screen unattended or play underneath.
Attention
Please read the following instructions carefully and keep them for future reference.
The manufacturer assumes no responsibility for damage to property or personal
injury when the screen is used outside the recommended specications, or in the
case of improper installation.
Do not use this screen near heaters or air conditioners. Also, do not mount the
product in direct sunlight or in front of a window. Due to the temperature-sensitive
PVC surface, it can lead to lasting damage to the projection screen.
We recommend that you wait approx. 2 hours after delivery for the assembly so
that the fabric can acclimatize; especially when the screen is brought from cold to
warm surroundings.
Please avoid any stains on the cloth surface. These may not be removable.
The positions of the endpoints are already optimally set at the factory and should
not be changed. Especially with Tension screens, the entire length of the fabric
should always be used to ensure the best atness. An adjustment of a few cm of the
end stop points should only be made by persons with specialist knowledge and / or
in consultation with the manufacturer. An incorrect setting may damage the screen.

Care Instructions
NEVER clean the screen with alcohol or other detergents that contain solvents. Use
only a soft and clean cloth with a mild soapy water, if necessary to remove dirt from
the surface. Be sure to avoid contact with sharp objects. These could permanently
damage the projection screen fabric.
In the box
Please check before beginning installation that all following parts are included! If
any parts are missing, contact the dealer where you purchased the product and
wait to receive them before completing the installation.
a) 1x screen
d) 2x Eyelet
g) 4x Universal screw
5x40mm
j) 4x Heavy Duty Dowel k) 1x Spirit Level l) 2x Remote control
(1 x Infrared, 1 x Radio)
h) 4x Plastic wall plugs
8mm
i) 2x Hexagon nut
b) 2x Mounting bracket
e) 2x Hook anchors
(for screens up to 135”)
c) 2x Ceiling mounting adapter
f) 2x M6 ceiling hook plate
(for screens from 135“)
3

5
4
Lieferumfang
m) 2x Carabiner
p) 1x Trigger cable q) 1x Infrared Eye
n) 1x Stop adjuster o) 1x Instruction Manual
Mounting the screen
Install the screen at a location visible to all viewers; ideally, the screen should be
mounted central to the spectators. The lower third of the screen should be at
about eye level of the viewer. The mounting brackets (b) should ideally be installed
between 200 and 300mm from each end of the screen. (see Fig. 1)
200-300 200-300
Wall Mounting
1. For mounting on a solid stone / concrete wall please use the heavy-duty dowels
(j) or plastic dowels (h). Determine the position for mounting the mounting
brackets (b) according to the housing dimensions and the height of the projection
screen. Draw a horizontal line (spirit level) to install the two mounting brackets at
the same height. (see Fig. 2)
Figure 1

6
5
Then drill 2 holes each with an 8mm drill,
insert the dowels into the holes and attach
the mounting brackets with either the hex
nuts (i) or the universal screws (g).
Figure 2
Horizontal line
Mounting the screen
2. Now lift the screen housing with
two people and insert it carefully into
the mounting bracket. Make sure that
the housing engages in the hooks of
the mounting brackets. Now slide the
housing slowly downwards. The screen
should click into place with a click
sound. (see Fig.3)
3. Finally tighten the safety screw of
the mounting bracket. This prevents
inadvertent release of the mounting
bracket. (see Fig. 4)
Figure 3
Figure 4
Ceiling mounting (Method 1)
CAUTION: Always ensure that the surface can support the weight of the screen
to prevent it from falling and causing an injury.

7
6
Mounting the screen
1. For mounting on a solid stone /
concrete surface please use the heavy-
duty dowels (j) or plastic dowels (h).
Determine the position for mounting the
mounting brackets (b) according to the
housing dimensions and the height of
the projection screen. Draw a horizontal
line (spirit level) to install the two
mounting brackets at the same height.
(see Fig. 5) Figure 5
Horizontal line
2. Now lift the screen housing with two
people and insert it carefully into the
mounting bracket. Make sure that the
housing engages in the hooks of the
mounting brackets. Now push the housing
slowly until the screen clicks into place with
a click. (see Fig.6)
Figure 6
3. Finally tighten the safety screw of the
mounting bracket. This prevents inadvertent
release of the mounting bracket. (see Fig. 7)
Figure 7

8
7
Mounting the screen
Figure 8
Ceiling mounting (method 2)
1. Slide the mounting plates on the top of the screen housing (a) outward.
(see Fig. 8)
2. For mounting on a solid stone / concrete ceiling,
please use heavy-duty dowels (j) or plastic dowels
(h). Determine the appropriate position of the
screen and transfer hole spacing to your ceiling.
Then drill 2 holes each with an 8mm drill,
insert the dowels into the holes and attach the
mounting brackets with either the hex nuts (i) or
the universal screws (g) depending on the dowel
selection (see Fig. 9) Figure 9
Figure 10
Hanging installation
1. Connect the eyelet (d) to the mounting bracket
(b). (see Fig. 10)
2. For mounting on a solid stone / concrete
surface, please use heavy-duty dowels (j) or plastic
dowels (h). Determine the suitable position for
mounting the hook dowel or ceiling hook plate (f).
Draw a straight line to install the two hooks in the
same alignment. (see Fig. 11)

9
8
Mounting the screen
Figure 11
3. Attach the mounting brackets (b) to the
back of the screen housing and tighten the
safety screw.
4. Now hang the screen into the hooks of
the previously installed ceiling hook plates.
5. If you require a longer suspension, please
use suitable material such as a metal chain
(see Fig. 12).
Figure 12
ATTENTION: Please check
hanging loads for integrity at least
once a year to prevent accidents!
Operation of the screen
Trigger
Connection Manual up
Manual down
Power
Connection
External IR
connection
RS485
connection
Screen:
Connect the power to the screen with the included power cord. Please pay
attention to correct voltage supply (230V / AC). Do not lay the cable on hot surfaces
and avoid unnecessary tension.

10
9
Remote control:
The delivery of the screen includes an infrared and a radio remote control. To use the
infrared remote control please use the enclosed IR receiver (q). Insert the jack plug
into the„ext. IR port„on the left side of the screen housing and orient the receiver so
that it has visual contact with the IR remote control.
Operating the remote control
1) Press the„Up“ button on the remote control. The screen will
automatically drive to the upper end position and automatically
stop.
2) Press the„Stop“ button on the remote control. The movement of
the screen stops immediately.
3) Press the„Down“ button on the remote control. The screen will
automatically drive to the lower end position and automatically
stop.
Operation of the screen
Pairing the radio remote control:
The radio remote control is already paired with the integrated receiver at the
factory. If the pairing is forgotten, please proceed as follows:
1) Press the„UP“ button for 3 seconds until the LED of the remote control lights
up, then connect the power cable to the screen. A beep conrms the pairing
mode that has been started.
2) Release the„up“ button when you hear the beep.
3) Briey press and release the„up“ button. When the beep sounds 3 times
quickly, the remote control pairing is complete.
Trigger:
With the trigger connection, the screen can automatically go up and down when
the projector is turned on and o. To do this, connect the screen via the trigger
connection to the trigger output of your projector. It may be necessary to enable
the trigger output of your projector software so that the projector sends the
control signals to the screen. For further information please refer to the operating
instructions of your device or contact the manufacturer of the projector.
Input voltage of trigger connection:
DC / AC 5V - DC / AC 20V

11
10
Operation of the screen
RS 232/485
A. RS485 port setting
1) Baud Rate: 2400
2) Data Length: 8
3) Odd-even Check: N
4) Start Bit: 1
5) Stop Bit: 1
C. Function Control
1) “Up” Command: The screen will go up.
2) “Stop” Command: The screen will stop.
3) “Down” Command: The screen will go down.
Assignment of the RJ-12 connector:
1: RS485-B
2: RS485-A
3: potential-free contact (Up)
4: potential-free contact (stop)
5: potential-free contact (down)
6: potential-free contact (ground)
IR communication protocol (codes):
Frame format: frame---delay110ms--- frame
Frame data: 2byte data----delay 43ms----2byte data
Data:
UP: 10110011-01111000 10110100-10000110
STOP: 10110000-11111000 10110111-00000110
DOWN: 10110111-01111000 10110000-10000110
Data from left to right are sent in turn:
„1” bit: 38KHZ carrier wave 246 µs (10pcs carrier wave), low level :1.76ms
“0” bit: 38KHZ carrier wave 246 µs (10pcs carrier wave), low level :766µs
The remote will always keep sending signals when always hit the button;
Indicator light ashes 1 time per second.
B. Control Code
1) “Up” Command: 0xFF 0xAA 0xEE 0xEE 0xDD
2) “Stop” Command: 0xFF 0xAA 0xEE 0xEE 0xCC
3) “Down” Command: 0xFF 0xAA 0xEE 0xEE 0xEE

EC Declaration of Conformity
celexon Germany GmbH & Co. KG hereby declares that the product
„DELUXX Cinema Electric Screen (Tension)“
complies with the essential requirements and other relevant regulations
Electromagnetic Compatibility Directive (2014/30 / EU)
The Low Voltage Directive (2014/35 / EU)
and the Radio Equipment Directive (2014/53 / EU)
equivalent. A copy of the EU Declaration of Conformity can be found at
www.deluxx.com/certicates.
Christoph Hertz
Managing Director
The symbol indicates the separate take-back of electrical and
electronic equipment in EU countries. Please do not dispose of
the device in the household waste.
Inform yourself about the return system valid in your country
and if you have any questions about the disposal process, please
contact your local authority and pollutant collection point.
celexon Germany GmbH & Co. KG – Gutenberstr. 2 – 48282 Emsdetten, Germany
www.deluxx.com – [email protected]om – TEL: [phone]