Celexon Expert Pure White User manual

User manual
celexon Expert xed frame
Pure White
Thank you for choosing a quality product from celexon.
Please read the instrucons carefully before you use the screen
and keep them for future reference!

1
• Do not start assembly before reading and understanding the complete manual.
• This product should only be installed by specialized personnel with mechanical
knowledge
• Tighten the screws, but do not over tighten them. Turning them too tight can
cause damage.
• This product is intended for indoor use. Outdoor use could damage the product.
• Hanging loads must be tested at least twice a year for strength and carrying
capacity.
• Carry out the assembly and installation with at least two persons to ensure a safe
installation.
Please read the following instructions carefully and keep them for later use. The
manufacturer assumes no responsibility for damage to property or personal injury
if the screen is used outside the recommended specifications or in case of improper
installation.
Do not use this screen near heaters or air conditioners. Also, do not install them in
direct sunlight or in front of a window. Due to the temperature-sensitive PVC surface,
damage may be caused to the projection screen.
We recommend that you wait approx. 2 hours after delivery for the assembly. This
will allow the fabric to acclimatize, especially if the fabric is brought in from a cold
environment to the warm. Please be very careful when handling the PVC screen fabric
and avoid any stains on the cloth surface. These may not be removable.
The information in this document is subject to change without prior notice.
Changes are made in the following versions of this manual. The manufacturer
does not guarantee the accuracy of the information in this document.
Safety Instructions
Disclaimer
Caution

2
NEVER clean the screen with alcohol or other cleaning agents that contain solvents.
Use only a soft and clean cloth. A mild soapy water may be used to remove dirt
from the surface. Be sure to avoid contact with sharp objects. These could damage
the projection screen.
Before installation, check that all the parts listed below are included! If any parts are
missing, contact the dealer where you purchased the product and do not begin the
installation until the items are received.
2x horizontal aluminum
frame part (A)
Note: Screens with an image
width greater than 300cm con-
sists of a frame part made from
two pluggable parts
2x vertical aluminum frame
part (B)
4 x Mounting brackets (D)1 x Projection fabric (C)
4 x Metal corners (E) 8 x Screws (F)
Care instructions
In the box
8 x Sliding threads (G) 4x Mounting hooks (I)2x Connectors (H)
Note: Only required if
note A applies

3
24 x mounting screws (J)
Note: If (A) is split, 8 extra pieces are also included in
delivery and if support strut (L) is required, extras are also
included (2 per strut)
Support strut (L)
Note:
For screens with a picture width up to 200cm, there is no support strut included
For screens with an image width of 250cm 1x support strut is included (except 4:3 format =
2 support struts)
For screens with a picture width from 280cm 3x struts are included
8x plastic plugs (K)
Lieferumfang
Installation
A. Frame construction
1. CAUTION: This step is only required if (A) is split. Otherwise, please continue to the
next step.
Lay the horizontal frame parts (A) flat on the floor. Put a clean and soft cloth under
the frame parts to prevent scratches to the surface. The two vertically cut sides next
to each other. Insert a connector (H) as shown in the image to a frame part. Make
sure that the holes are lined up. Now screw on the into the connector (H) with two
screws (J). When this is attached, slide the element into the other frame part (A)
and pay attention again that the holes are lined up. Now screw with two screws (J)
firmly. Repeat this step once again with the other components. This step is comple-
ted when you have two completed horizontal frame parts.

4
Installation
2. For each horizontal frame piece (A), insert the following number of sliding threads
(G) as shown:
For screens with a picture width up to 250cm = 2x (G) per frame part
For screens with a picture width from 280cm = 3x (G) per frame part
3. Place all four frame parts 2x (A) and 2x
(B) in the final position on the ground
(Fig. 1)
4. Insert a metal corner (E) into the
horizontal frame sections (A) at each
end (Fig. 2)
Fig. 1
Fig. 2
5. Slide the vertical frame parts (B) onto the corners (Fig. 3)
Fig. 3

5
Installation
6. Slide the lower horizontal frame part (A)
on the vertical frame parts (B) (Fig. 4)
7. Once all the frame parts are nested, each corner is secured into place with 4x screws
(J) (Fig. 5)
8. ATTENTION: This step is only necessary if sup-
port strut (L) is included in delivery. Otherwise,
please move to the next step.
Align the sliding threads (G) according to Fig. 6
depending on the number of enclosed struts
(L) as follows:
Fig. 4
Fig. 5
Fig. 6
1x Support strut (L) included 2x Support strut (L) included

6
Installation
3x Support strut (L) included
B. Attaching the fabric
1. Lay the projection fabric with the projection side down on a soft clean surface.
Make sure that the surface is not dirty. Carefully position the frame in the center
with the flat side down on the projection cloth. If there is a seam in the viewing area
of the projection fabric, please arrange the fabric so that it is located in the upper
area of the screen.
2. Now fix the projection cloth with the already pre-assembled Velcro strips
the frame.

7
Installation
Proceed as follows:
• Start with a horizontal side and pull the pro-
jection fabric with the Velcro strip on the back
of the frame. Ensure that you are doing so in a
good alignment to the frame and the projecti-
on screen in the corners (Fig. 7).
Now follow these steps on the opposite side
and try to tension the projection fabric as best
as possible before fixing it with the velcro
strips.
• Now place the corner flap with enough tension on the narrow frame side (Fig.
8) and fix the vertical side of the projection screen with the velcro strips on the
aluminum frame. Repeat the step on the opposite side, stretching the projection
screen as much as possible (Fig. 9).
Fig. 7
Fig. 8 Fig. 9
Fig. 10
C. Mounting the screen
1. Mount two hooks (I) per
horizontal frame section
(A). Make sure the hooks
are evenly distributed
along the length and oppo-
site each other (as shown
in Fig.10)

8
Installation
2. Measure the distance H and L (as
shown in Fig. 10) and transfer it on
the wall (Fig. 11)
3. Mount the mounting bracket (C) with
the screws (F) and the plastic dowels (K)
onto a suitable and stable surface. You
can use your own screws / plugs if they
are more suitable for your surface.
4. Hang the screens as shown in Fig.12 on
the brackets.
Fig. 11
Fig. 12

www.celexon.com
celexon Europe GmbH
Gutenbergstraße 2
D-48282 Emsdetten