Celexon INF200 User manual

Operating instructions
celexon inatable outdoor
screen INF200
Thank you for purchasing this product. For optimum performance and safety, please
read these instructions carefully before connecting or operating this product. Please
retain these instructions for future reference
Version: 32422_071

1
The purpose of these operating instructions is to familiarise you with the operation of
this product. Therefore, keep these instructions in a safe place so that you can access
them at any time.
• Before installation, please refer to the enclosed data sheet for further safety and use
instructions.
• Do not begin installation until you have read and understood the complete opera-
ting instructions.
• Carry out the installation with another person to ensure safe installation.
• Remove the product from its packaging and remove all packaging materials. Make
sure that there is no packaging material on or in the product. If you notice any da-
mage to the packaging, also check for damage to the product. If you notice any ex-
ternal damage to the unit or unexpected unusual functioning, do not continue to use
or assemble the product. Immediately contact the dealer from whom you purchased
the product or celexon directly (Web: www.celexon.co.uk, Mail: [e-mail])
for further information.
• The use of the screen and accessories is forbidden to children under 16 years of age.
• Ensure that no children play with the screen or are in the vicinity without
supervision.
• Converting or modifying the product compromises product safety.
• Caution: Risk of injury! Never modify the product yourself. Never carry out repairs
yourself!
• This product may only be used in its original, unmodied condition.
• Do not use the product in the vicinity of devices that emit gases or water or in a
dusty environment.
• Handle the product with care. It can be damaged by knocks, blows or falling from a
• from even a small height.
• Keep the product away from moisture and heat.
• Never immerse the product in water or other liquids.
• Use the product only in its intended manner. Other use may result in damage to the
product or its surrounding environment.
• Failure to follow the above instructions may result in personal injury and damage
to the product or equipment attached to it. Incorrect installation or use may also
invalidate the warranty may be voided.
WARNINGS

2
• If you are unsure about the use of the product, please contact your specia-
list personnel, your dealer or celexon directly (Web: www.celexon.co.uk, Mail:
[e-mail]).
The manufacturer accepts no responsibility for damage to property or personal injury,if
the screen is used outside the recommended specications, or in the event of improper
installation. Do not use this screen in the vicinity of heaters or air conditioners. Also,
do not mount the product in direct sunlight or in front of a window. Due to the tempe-
rature-sensitive PVC surface, the projection screen fabric may be permanently damaged.
We recommend that you wait approx. 2 hours after delivery before installing the projecti-
on screen. This way you will allow the screen to acclimatise, especially when moving from
a cold to a warm environment (or vice versa).
Please avoid any stains on the surface of the screen. These may not be able to be re-
moved.
• Note the front and back of the fabric when attaching.
• Please check ALL parts for damage or scratches before assembly!
• The screen may only be placed on a at surface free of sharp or pointed objects.

3
GENERAL NOTES
• If the projection screen fabric does not have a satisfactory atness, correct
this by loosening the Velcro strips and repositioning the projection the
fabric accordingly. Depending on the temperature, the surface of the fra-
me may be larger than the projection screen surface. In this case, slightly
compress the frame to allow the velcro strips to reach it. Wrinkles in the
projection surface usually disappear by themselves after a short time.
• After unpacking or long storage, wrinkles are sometimes unavoidable with
this type of product. Placing the projection screen in a sunny (warm area)
supports and accelerates this process. If possible, set up the screen 1-2
hours before you actually use it. Any creases should disappear or diminish
considerably in a warm environment.
• During viewing from a normal distance of a few metres, these creases do
not disturb the projection. This type of product is only suitable to a limi-
ted extent for use with short-distance or especially ultra-short distance
projectors. Typically with this technology, this type of projector requires
a perfectly at surface in order to get a distortion free image which is not
possible with this frame.
• Open the zip a little when the screen is fully erected to relieve the motor
fan.
• Store the screen in a dry and cool environment. If the screen becomes wet
during use, allow it to dry completely before disassembling and storing.

4
The information in this document is subject to change without notice by the
manufacturer. Changes will be added to subsequent versions of this manual.
Errors expected.
DISCLAIMER
IMPORTANT SAFETY INSTRUCTIONS
• The screen must not be used in winds stronger than gale force 2 to prevent
it from ying around! Do not erect the screen in windy conditions!
• If the wind exceeds gale force 2 during use, pull out the projection screen
fabric immediately from the frame and then let the air out of the frame.
• The blower is not waterproof and may only be operated in dry weather.
• If it starts to rain, never unplug the blower with damp hands or in an area
exposed to rain.
• Never leave the screen unattended and do not let children in the immedi-
ate vicinity of the screen.
• Never lay the tensioning cords in walkways and, if necessary, mark them
with coloured cloths to prevent stumbling. The pegs may only be ancho-
red in solid ground, Check that they are rmly anchored before use. Sandy
ground does not provide sufcient support for the pegs and pulling them
out accidentally can injure people. If necessary, obtain additional pegs sui-
table for your ground from a specialist dealer.
• Always ensure that the necessary safety precautions are taken and that
there are adequate, secure fastening possibilities.

5
IN THE BOX
Inatable frame (A) PVC projection screen fabric (B)
Electric pump (C) Guy line kit (D)
INSTALLATION NOTES
Before installation, please check that all the parts listed above are included. If
any parts are missing, contact the dealer from whom you purchased the pro-
duct and wait until they arrive for installation. It is recommended to assemble
the screen with a second person.
CARE INSTRUCTIONS
NEVER clean the screen with alcohol or other cleaning agents containing sol-
vents. Use only a soft and clean cloth. If necessary, dirt can be removed from
the surface with a mild soap solution (max. 5%). It is essential to avoid contact
with pointed or sharp objects. These could permanently damage the projecti-
on screen fabric. Further instructions can be found in the enclosed projection
screen instructions.
Small holes in the frame can be repaired with the enclosed patch kit.

6
INSTALLATION
STEP 1:
Lay and spread out the frame of the screen (A) on a at surface. Make sure
that the front is facing upwards (Velcro upwards) and that the zip on the lower
frame piece is closed.
STEP 2:
Spread out the projection screen fabric (B) and hold it with a second person
at the outer corners. Start at the two upper corners and place the projection
screen fabric on the velcro surface of the frame. The velcro on the frame is
deliberately made a little larger than the velcro on the fabric, This allows for
optimal tensioning and atness of the fabric for later use.
Align the fabric so that the two corners
of the upper long side of the fabric can
be attached to the velcro inside of the
frame (Fig. 1). Then connect the midd-
le section of the upper long side of the
fabric to the Velcro of the frame. Guide
the fabric as close as possible to the
outer edges of the Velcro on the frame.
Fig. 1: Velcro strip
Projection screen fabric and
frame
Depending on the temperature, the fabric can shrink and the gap between the
frame and the projection surface may vary, which can make installation more
difcult.

7
STEP 3:
Continue in the same way with the two shorter sides and nally with the lower
long side.
As a result, the Velcro should be attached to the inside of the frame right
the way around the frame. Sometimes it is necessary that the long sides are
somewhat compressed or gathered with the fabric, this provides the best at-
ness or fabric tension. (The fabric is always „pulled“ outwards from the frame
in the middle). Depending on the temperature, there may also be different
lengths between the frame and the projection surface. In this case, try to pull
the Velcro strip from the frame a little, or store the fabric for a few hours in
normal room conditions to achieve the „normal“ size of the material.
Always pull the fabric only by the outer sewn-on tape, not by the PVC material
itself, so as not to damage or overstretch the material. After the rst applica-
tion you will immediately recognise the optimum process, a correction of the
Velcro can still be made even when inated. The strap sewn all around the fab-
ric still ensures that you end up with a rectangular projection surface.
The Velcro strip on the frame being considerably wider than that of the fabric
gives the possibility of exibly adapting the fabric to the frame.
Place the fan behind the screen and tie
the air hose of the frame tightly around
the air outlet of the blower. For this
purpose you will nd laces sewn to the
hose. Two sets are available, a shorter
length if you do not have the space,
and a full length set for where you have
more space.
STEP 4:
Fig. 2: wall and
Set up motor fan
Roll up the hose as far as it will go and put it over the air outlet of the blower,
tie the cords around it and fasten them, attaching the hose to the blower. Al-
ternatively, use the 2nd pair of laces to tie the blower as far away as possible
behind the frame, thus reducing the noise.

8
Attention:
During the ination process, make sure that the frame does not twist and that
the motorised blower does not tip over. If necessary, support the frame while
setting it up.
STEP 5:
Use the guy accessories (D), to anchor
the screen and stop it from falling over.
Pass the pegs through the loops of the
lower frame and anchor them rmly in
the ground.
Tie the ropes to the the upper loops and
tighten them downwards at an angle of
approx. 60° downwards (Fig. 3). Fig. 3: Anchoring the screen
DISASSEMBLY
Switch off the fan, unzip the frame and guide the screen with two people as
it „collapses“. The frame should tilt backwards and the screen surface should
face upwards.
STEP 2:
Disconnect the pump from the power source, loosen the air hose and move the
blower and any extension cord or cable reel into the dry, Loosen all the pegs
from the ground and if necessary, remove the guy ropes from the frame. Place
the sharp pegs safely to one side.
STEP 3:
Hold the frame rmly with one person while the other releases the fabric from
the frame. Pull only on the outer band of the fabric to release it all the way
around.

9
STEP 4:
Carefully fold the fabric. Make sure it is only folded when dry and that there are
no objects, leaves or insects in between as this could cause permanent stains
or even tears in the fabric. When folding, use the padding at the folding points
to keep creases to a minimum.
Do not fold the fabric more than necessary for storage. Do not put pressure on
the fabric during storage to avoid creases.
STEP 5:
Fold the frame and drive the air in the direction of the unzipped section. It is
easier to let the frame rest for some time (approx. 20-30 minutes) after dea-
ting. This way, a large part of the air escapes and folding is much easier.
STEP 6:
Repack the components. It is suggested to store the fabric away from the fra-
me and fan to ensure that there is as little pressure as possible on the folded
fabric during storage. If necessary, store the pegs separately to avoid damage
to the material during storage or transport.

10
Manufacturer: celexon Europe GmbH
Address: Gutenbergstraße 2, 48282 Emsdetten, DE
Product name: celexon inatable outdoor screen INF200
Products that are marked with the CE mark meet all requirements of the rele-
vant EU directives. The EU declaration of conformity can be downloaded from
the following address: www.celexon.de/zertikate
INFORMATION ON EU CONFORMITY
The symbol indicates the separate collection of electrical and electronic
devices in EU countries. Please do not throw the device into household
waste. Find out about the return system applicable in your country and
contact your local authority or your local waste and pollutant collection
point if you have any questions about the disposal process.

11
Manufacturer: celexon Europe GmbH
Address: Gutenbergstraße 2, 48282 Emsdetten, DE
Product name: celexon inatable outdoor screen INF200
Products that are marked with the UKCA mark meet all requirements of the
relevant UK directives. The UK declaration of conformity can be downloaded
from the following address: www.celexon.de/zertikate
INFORMATION ON UK CONFORMITY
The symbol indicates the separate collection of electrical and electronic
devices in EU countries. Please do not throw the device into household
waste. Find out about the return system applicable in your country and
contact your local authority or your local waste and pollutant collection
point if you have any questions about the disposal process.