Chauvet EZMiN Laser FX User manual

`
User Manual
English
Español
Français
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R Laser PRODUCT
CLASSIFIED PER EN/IEC 60825-1:2007
Complies with FDA performance standards for
laser products except for deviations pursuant
to Laser Notice No. 50, dated June 24, 2007.

Page 2 of 48 EZMiN™ Laser FX/RBX User Manual Rev. 3
TABLE OF CONTENTS
1. Before You Begin .......................................................................................................... 4
What Is Included...............................................................................................................................4
Unpacking Instructions.....................................................................................................................4
Claims ....................................................................................................................................................... 4
Manual Conventions.........................................................................................................................4
Symbols............................................................................................................................................4
Disclaimer.........................................................................................................................................4
Safety Notes.....................................................................................................................................5
Non-Interlocked Housing Warning............................................................................................................. 6
Laser Safety Notes.................................................................................................................................... 6
Laser Safety Label Reproduction.....................................................................................................7
Laser Exposure Warning........................................................................................................................... 8
Laser Emission Data ........................................................................................................................8
2. Introduction ................................................................................................................... 9
Overview...........................................................................................................................................9
Dimensions.....................................................................................................................................10
3. Setup .............................................................................................................................11
AC Power .......................................................................................................................................11
Charging the Battery ......................................................................................................................11
Battery Runtime..............................................................................................................................11
Battery Maintenance................................................................................................................................ 11
Mounting.........................................................................................................................................12
Orientation............................................................................................................................................... 12
Rigging.................................................................................................................................................... 12
Proper Usage .......................................................................................................................................... 13
4. Operation ......................................................................................................................14
Manual Mode..................................................................................................................................14
Wireless Remote (IR).....................................................................................................................14
5. Technical Information ..................................................................................................15
Product Maintenance .....................................................................................................................15
6. Technical Specifications ..............................................................................................16
Returns...........................................................................................................................................17
Contact Us......................................................................................................................................17
1. Antes de Empezar ........................................................................................................18
Qué va Incluido...............................................................................................................................18
Instrucciones de Desembalaje.......................................................................................................18
Reclamaciones........................................................................................................................................ 18
Convenciones del Manual..............................................................................................................18
Símbolos.........................................................................................................................................18
Exención de Responsabilidad........................................................................................................18
Notas de Seguridad........................................................................................................................19
Advertencia sobre Carcasa no Cerrada .................................................................................................. 20
Notas de Seguridad sobre Láser............................................................................................................. 20
Reproducción de la Etiqueta de Seguridad del Láser....................................................................22
Advertencia sobre Exposición al Láser.................................................................................................... 23
Datos de Emisión Láser .................................................................................................................23
2. Introducción .................................................................................................................24
Vista General..................................................................................................................................24
Dimensiones...................................................................................................................................25

EZMiN™ Laser FX/RBX User Manual Rev. 3 Page 3 of 48
3. Instalación ....................................................................................................................26
Corriente Alterna ............................................................................................................................26
Cargar la Batería............................................................................................................................26
Duración de la Batería....................................................................................................................26
Mantenimiento de la Batería.................................................................................................................... 26
Montaje...........................................................................................................................................27
Orientación.............................................................................................................................................. 27
Colocación............................................................................................................................................... 27
Uso Adecuado......................................................................................................................................... 28
4. Funcionamiento............................................................................................................29
Modo Manual..................................................................................................................................29
Mando a Distancia Inalámbrico (IR)...............................................................................................29
5. Información Técnica ....................................................................................................30
Mantenimiento del Producto...........................................................................................................30
6. Especificaciones Técnicas ..........................................................................................31
Devoluciones..................................................................................................................................32
Contacto .........................................................................................................................................32
1. Avant de Commencer ..................................................................................................33
Ce Qui est Compris........................................................................................................................33
Instructions Relatives au Déballage...............................................................................................33
Réclamations........................................................................................................................................... 33
Conventions de ce Manuel.............................................................................................................33
Symboles........................................................................................................................................33
Clause de Non-Responsabilité.......................................................................................................33
Consignes de Sécurité ...................................................................................................................34
Avertissement : Boîtier non Verrouillable................................................................................................. 36
Consignes de Sécurité Relatives au Laser.............................................................................................. 36
Reproductions des Etiquettes en Matière de Sécurité des Appareils Laser..................................38
Avertissement d'Exposition au Laser....................................................................................................... 39
Données d'Emission Laser.............................................................................................................39
2. Introduction ..................................................................................................................40
Aperçu ............................................................................................................................................40
Dimensions.....................................................................................................................................41
3. Configuration ................................................................................................................42
Alimentation CA..............................................................................................................................42
Chargement de la Batterie .............................................................................................................42
Autonomie de la Batterie................................................................................................................42
Entretien de la Batterie............................................................................................................................ 42
Installation ......................................................................................................................................43
Orientation............................................................................................................................................... 43
Suspension.............................................................................................................................................. 43
Utilisation Adéquate................................................................................................................................. 44
4. Fonctionnement ...........................................................................................................45
Mode Manuel..................................................................................................................................45
Télécommande Sans Fil (Infrarouge).............................................................................................45
5. Informations Techniques .............................................................................................46
Entretien de l'Appareil ....................................................................................................................46
6. Spécificités Techniques ...............................................................................................47
Renvois...........................................................................................................................................48
Nous Contacter...............................................................................................................................48

Page 4 of 48 EZMiN™ Laser FX/RBX User Manual Rev. 3
1.BEFORE YOU BEGIN
What is
Included
•EZMiN™ Laser FX/RBX
•External power supply
•Hanging bracket with mounting
hardware
•Flexible tripod
•IR remote
•Warranty card
•User Manual
Unpacking
Instructions
Carefully unpack the product immediately and check the box to make sure all the parts
are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from
shipping or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Failure to do so in a timely manner may invalidate your claim with the carrier. In addition,
keep the container and all the packing material for inspection.
For other issues, such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Manual
Conventions
Convention Meaning
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
ENTER
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information.
Ignoring this information can cause the product to not work,
damage it, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this document are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
omissions that may appear in this manual, and reserves the right to revise or recreate
this manual at any time. Download the latest version from www.chauvetlighting.com.
© Copyright 2013 CHAUVET®. All rights reserved.
Printed in P.R.C.
Electronically published by CHAUVET® in the United States of America.
Author
Date
Editor
Date
A. Leon 10/23/13 D. Couppe 10/23/13

EZMiN™ Laser FX/RBX User Manual Rev. 3 Page 5 of 48
Safety Notes
The Safety Notes include important laser system safety information. Read and
understand all instructions before powering on the laser for the first time. Knowing these
safety instructions is crucial to avoiding laser eye injury and breaking the law. Keep this
User Manual in a safe place for future reference.
STOP AND READ ALL LASER SAFETY DATA
•Lasers can be hazardous and have unique safety considerations. Permanent
eye injury and blindness is possible if lasers are used incorrectly. Pay close
attention to each safety REMARK and WARNING statement in this User
Manual. Read all instructions carefully BEFORE operating this device.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a safety
cable.
•Make sure there are no flammable materials close to the product when operating.
•Do not touch the product’s housing when operating because it may be very hot.
•Do not remove the bracket at any time. This product is intended to be used with its
bracket.
•This product is not intended for permanent installation.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least
20 in (50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Always use the mounting bracket to carry the product.
•Do not switch the product on/off in short intervals. This will reduce the laser diode life.
•Do not shake this product. Avoid brute force when mounting or operating this product.
•ALWAYS use a safety cable when mounting the product overhead.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Contact the nearest authorized technical assistance center.
•Avoid direct eye contact with laser light. Never intentionally expose your eyes or
others to direct laser light.
•This laser product can potentially cause instant eye injury or blindness if laser light
directly strikes the eyes.
•It is illegal and dangerous to shine this laser into audience areas, where the
audience or other personnel could get direct laser beams or bright reflections into
their eyes.
•It is a U.S. federal offense to shine any laser at aircraft.
•Use of controls, adjustments, or procedures other than those specified in this User
Manual may result in hazardous radiation exposure.
•Do not attempt any repairs. Repairs and servicing must be carried out by a certified
technician. Unauthorized modifications are forbidden for safety reasons!
•Keep this User Manual for future consultation. If transferring ownership of the
product to another user, be sure this document is kept with the laser.

Page 6 of 48 EZMiN™ Laser FX/RBX User Manual Rev. 3
Non-Interlocked
Housing Warning
•This unit contains high power laser devices internally.
•Do not open the laser housing, due to potential exposure to unsafe levels of laser
radiation.
•
The laser power levels, accessible if the unit is opened, can cause instant blindness,
skin burns, and fires.
Laser Safety
Notes
STOP AND READ ALL THE LASER SAFETY NOTES BELOW
Laser light is different from any other light sources. The light from this product can
potentially cause eye injury if the product is not set up and used properly. Laser light is
thousands of times more concentrated than light from any other kind of light source. This
concentration of light can cause instant eye injuries, primarily by burning the retina (the
light-sensitive portion at the back of the eye). Even if you cannot feel “heat” from a laser
beam, it can still potentially injure or blind you or your audience. Even very small
amounts of laser light are potentially hazardous—even at long distances. Laser eye
injuries can happen faster than you can blink.
DO NOT assume
that because laser entertainment products split the laser into hundreds
of beams and that the laser beam is scanned out in high speed, that an individual laser
beam is safe for eye exposure. This laser product uses dozens of milliwatts of laser
power (Class 3B levels internally) before it splits into multiple beams (Class 3R levels).
Many of the individual beams are potentially hazardous to the eyes.
DO NOT assume that because the laser light is moving, it is safe. Laser light is never without
risk, nor do the laser beams always move. Since eye injuries can occur instantly, it is critical
to prevent the possibility of ANY direct eye exposure. According to laser safety regulations, it
is not legal to aim Class 3R lasers into areas where people can get exposed. This is true
even if the laser is aimed below people’s faces, such as on a dance floor.
•Do not operate the laser without first reading and understanding all safety and
technical data in this manual.
•ALWAYS set up and install all laser effects so that all laser light is at least
9.8 feet (3 meters) above the floor on which people can stand.
See the Proper Usage section of this manual.
•
After setup, and prior to public use, test laser to ensure proper function. Do not use if
any defect is detected.
•DO NOT use laser if the laser appears to be emitting only one or two beams, rather
than dozens/hundreds, as this could indicate damage to the diffraction grating optic,
and could allow emission of laser levels higher than Class 3R.
•DO NOT point lasers at people or animals.
•Never look into the laser aperture or laser beams.
•DO NOT point lasers into
areas in which people can potentially get exposed, such as
uncontrolled balconies, etc.
•DO NOT point lasers at highly reflective surfaces such as windows, mirrors, and
shiny metal. Even laser reflections can be hazardous.
•Never point a laser at aircraft; this is a U.S. federal offense.
•Never point un-terminated laser beams into the sky.
•Do not expose the output optic (aperture) to cleaning chemicals.
•Do not use the laser if the housing is damaged, open, or if the optics appear
damaged in any way.
•Never open the laser housing. The high laser power levels inside of the protective
housing can start fires or burn skin, and will cause instant eye injury.
•Never leave this product running unattended.
•The operation of a Class 3R laser show is only allowed if the show is controlled by a
skilled and well-trained operator, familiar with the data included in this manual.
•The legal requirements for using laser entertainment products vary from country to
country. The user is responsible for the legal requirements in the location/country of
use.
CAUTION! DO NOT operate this device in ways not specified in this User Manual. Failure to follow
the instructions will void the warranty, may damage the product, or injure the user or the audience.
CAUTION! This product cannot be discarded with household waste. Contact your local waste
management service for electronic disposal regulations in your area.

EZMiN™ Laser FX/RBX User Manual Rev. 3 Page 7 of 48
Laser Safety Label Reproduction
Front
Rear
Top
Bottom

Page 8 of 48 EZMiN™ Laser FX/RBX User Manual Rev. 3
Laser
Exposure
Warning
LASER LIGHT AVOID DIRECT EYE EXPOSURE
Further guidelines and safety programs for safe use of lasers can be found in the ANSI
Z136.1 Standard “For Safe Use of Lasers”, available from the Laser Institute of America:
www.laserinstitute.org. Many local governments, corporations, agencies, military, and
others, require all lasers to be used under the guidelines of ANSI Z136.1. Laser Display
guidance can be obtained via the International Laser Display Association:
www.laserist.org.
Laser Emission Data
EZMiN™ Laser FX
Laser Classification Class 3R
Green Laser Medium DPSS Nd:YVO4, 532 nm
Red Laser Medium LD GaAIAs, 650 nm
Beam Diameter < 5mm at aperture
Pulse Data All pulses < 4 Hz (> 0.25 sec)
Divergence (each beam) < 2 mrad
Divergence (total light) < 160 degrees
Laser Power of Each
Beam from Aperture* < 5 mW
EZMiN™ Laser RBX
Laser Classification Class 3R
Blue Laser Medium LD InGaN, 450 nm
Red Laser Medium LD GaAIAs, 650 nm
Beam Diameter < 5mm at aperture
Pulse Data All pulses < 4 Hz (> 0.25 sec)
Divergence (each beam) < 2 mrad
Divergence (total light) < 160 degrees
Laser Power of Each
Beam from Aperture* < 5 mW
*As measured under IEC measurement conditions for classification.
Laser
Compliance
Statement
This laser product complies with EN/IEC 60825-1 Ed 2, 2007-03, and U.S. FDA/CDRH
FLPPS via the terms of Laser Notice No. 50 dated June 24, 2007. This laser device is
classified 3R. (Class 3R is the international equivalent of U.S. Class IIIa.) No maintenance
is required to keep this product in compliance with laser performance standards.

EZMiN™ Laser FX/RBX User Manual Rev. 3 Page 9 of 48
2.INTRODUCTION
Overview
Mode Button
Cooling Fan
Power In
Microphone
IR Remote
Receiver
LED Indicator
Laser Output
Battery
Switch

Page 10 of 48 EZMiN™ Laser FX/RBX User Manual Rev. 3
Dimensions
5.5 in
140 mm
1.9 in
48 mm
6.4 in
163 mm

EZMiN™ Laser FX/RBX User Manual Rev. 3 Page 11 of 48
3.SETUP
AC Power
The EZMiN™ Laser FX/RBX has an external auto-ranging power supply and it can work
with an input voltage range of 100 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the Technical Specifications. The listed current rating indicates the product’s
average current draw under normal conditions.
Always connect the product to a protected circuit (circuit breaker or fuse). Make sure the
product has an appropriate electrical ground to avoid the risk of electrocution or fire.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
Charging the
Battery
The EZMiN™ Laser FX/RBX comes with a rechargeable lithium battery for cable-free
operation. To charge the battery, simply plug in the power cord at any time before,
during, or after operation.
The EZMiN™ Laser FX/RBX battery should be charged 24 hours prior to initial use for
optimal battery life.
Battery
Runtime
The maximum runtime for the EZMiN™ Laser FX/RBX
battery is up to 6 hours; however,
the operation mode used has a bearing on the final runtime for the battery. T
o achieve
the maximum battery runtime, set the product in the Sound-
Active modes only. When
using the Automatic modes, the battery runtime may be shortened.
Battery
Maintenance
To keep the battery in optimal operating condition, store the product in a cool, dry place
and charge at least once every 30 days when not in use.
Avoid exposure to extreme temperatures. If the product is exposed to extreme cold or
hot temperatures, warm up/cool down the product before use and before charging.

Page 12 of 48 EZMiN™ Laser FX/RBX User Manual Rev. 3
Mounting
Before mounting the product, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The EZMiN™ Laser FX/RBX must be mounted in a position that includes planning for
safe laser usage. In addition, make sure adequate ventilation is provided around the
product.
Rigging
•Before deciding on a location for the product, always make sure there is easy access
to the product for maintenance and programming.
•Make sure that the structure or surface onto which you are mounting the product can
support the product’s weight (see the Technical Specifications).
•When mounting the product overhead, always use a safety cable. Mount the product
securely to a rigging point, such as an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The double-bracketed yoke has 13-mm holes, which
are appropriate for this purpose.
•The bracket adjustment knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
•The included flexible tripod serves as a surface support. See Proper Usage.
Do not remove the bracket at any time. This product is intended to be used with its
bracket.
Surface
Support
Mounting Clamp
Safety Cable
Overhead
Mounting

EZMiN™ Laser FX/RBX User Manual Rev. 3 Page 13 of 48
Proper Usage
This product is for overhead mounting only. For safety purposes, CHAUVET®
recommends mounting lighting effect products on steady elevated platforms or
sturdy overhead supports using suitable hanging clamps. In all cases, use
safety cables. Obtain appropriate mounting hardware from your lighting vendor.
International laser safety regulations require that laser products must be
operated in the fashion illustrated below, with a minimum of 9.8 feet
(3 meters) of vertical separation between the floor and the lowest laser
light. Additionally, 9.8 feet (3 meters) of horizontal separation is required
between laser light and audience or other public spaces.
CAUTION! USE OF CONTROLS, ADJUSTMENTS, OR PROCEDURES
OTHER THAN THOSE SPECIFIED IN THIS USER MANUAL MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
3 meters
3 meters

Page 14 of 48 EZMiN™ Laser FX/RBX User Manual Rev. 3
4.OPERATION
•This product is not designed for continual use. Make sure there are regular breaks during
operation to maximize the life of your laser.
•Always disconnect the EZMiN™ Laser FX/RBX from power when not in use.
Manual Mode
Access the four different operating modes available in this product by using the
MODE button on the front panel.
•Pressing and holding the MODE button for 2.5 seconds will toggle the
product on/off.
•Press MODE to cycle through the modes.
Mode
Description
1
Sound-Active A
2
Sound-Active B
3
Automatic A (fast effects)
4
Automatic B (slow effects)
The LED indicator on the front of the product will be blue when a Sound-Active
mode is selected. The LED indicator is red when an Automatic mode is selected.
Wireless
Remote (IR)
The wireless remote (IR) will immediately override the MODE button. No
additional settings are required.
In Sound-Active mode:
•Using the IR to set the sound sensitivity, press 1(least sensitive)
through 9(most sensitive).
Any control or setting on the remote control will be saved until the system is
rebooted. The system will revert to Automatic mode after reboot.
Cycles through auto
programs
Cycles through colors
In Manual mode, selects speed:
1to 8(fast to slow), 9(on), 0(off)
Cycles through
Sound-Active modes
Turns the laser on/off
In Manual mode,
rotates the effect‘s
direction
In Manual mode, selects effect:
A(red), B(green-FX/blue-RBX),
C(effect speed)
Pauses the effect

EZMiN™ Laser FX/RBX User Manual Rev. 3 Page 15 of 48
5.TECHNICAL INFORMATION
Product
Maintenance
Dust build-up reduces light output performance and can cause overheating. To
maintain optimum performance, clean the product at least twice a month.
However, usage and environmental conditions contribute to increasing the
cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust
collected on the external surfaces and fan vents.
4. Clean the glass panel (laser aperture) with a mild solution of glass cleaner
or isopropyl alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning
tissue.
6. Softly wipe any dirt or grime to the outside edges of the glass.
7. Gently polish the glass surface until they are free of haze and lint.
Always dry the glass surfaces carefully after cleaning them.
Do not spin the fan using compressed air because you could damage it.
Do not open this product for cleaning or servicing.

Page 16 of 48 EZMiN™ Laser FX/RBX User Manual Rev. 3
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
6.4 in (163 mm)
5.5 in (140 mm)
1.9 in (48 mm)
1.3 lb (0.1 kg)
Dimensions in inches rounded to the nearest decimal digit.
Power
Input Voltage
Range
Voltage Selection
12 VDC, 1.0 A
100 to 240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
1 W
1 W
Operating
0.1 A
0.1 A
Power I/O
US/Worldwide
UK/Europe
Power Cord plug
Edison (US)
Local plug
Light Source
EZMiN™ Laser FX
Type
Power
Wavelength
Laser (green)
50 mW
532 nm
Laser (red)
100 mW
650 nm
EZMiN™ Laser RBX
Type
Power
Wavelength
Laser (blue)
80 mW
450 nm
Laser (red)
100 mW
650 nm
Photo Optic
Parameter
Coverage angle
100º
Battery
Parameter
Maximum runtime
Up to 6 hours
Recharge time
Up to 5 hours
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Fan-cooled
Ordering
Product Name
Item Code
UPC Code
EZMiN™ Laser FX
10060763
781462211110
EZMiN™ Laser RBX
10060764
781462211127

EZMiN™ Laser FX/RBX User Manual Rev. 3 Page 17 of 48
Returns
In case you need to get support or return a product:
•If you are located in the U.S., contact CHAUVET® World Headquarters.
•If you are located in the UK or Ireland, contact CHAUVET® Europe Ltd.
•If you are located in any other country, DO NOT contact CHAUVET®.
Instead, contact your local distributor. See www.chauvetlighting.com for
distributors outside the U.S., UK, or Ireland.
If you are located outside the U.S., UK, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® products to
them. Visit our website for contact details.
Call the corresponding CHAUVET® Technical Support office and request a
Return Merchandise Authorization (RMA) number before shipping the product.
Be prepared to provide the model number, serial number, and a brief
description of the cause for the return.
Send the merchandise prepaid, in its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any
product returned without an RMA number.
Write the RMA number on a properly affixed label. Do not write the RMA
number directly on the box.
Before sending the product, clearly write the following information on a piece of
paper and place it inside the box:
•Your name
•Your address
•Your phone number
•RMA number
•A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from
inadequate packaging will be your responsibility. FedEx packing or double-
boxing are recommended.
CHAUVET® reserves the right to use its own discretion to repair or replace
returned product(s).
Contact Us
CHAUVET®
World Headquarters
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: 954-577-4455
Fax: [phone]
Toll free: 1-800-762-1084
CHAUVET® Europe Ltd.
United Kingdom & Ireland
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: 954-577-4455 (Press 4)
Fax: [phone]
Email: [e-mail]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk

Página 18 de 48 EZMiN™ Laser FX/RBX Manual de Usuario Rev. 3
1.ANTES DE EMPEZAR
Qué va
Incluido
•EZMiN™ Laser FX/RBX
•Fuente de alimentación externa
•Soporte para colgar con material de
montaje
•Trípode flexible
•Mando a distancia por IR
•Tarjeta de garantía
•Manual de usuario
Instrucciones
de
Desembalaje
Desembale el producto con cuidado inmediatamente y compruebe la caja para
asegurarse de que todas las piezas están en el paquete y en buen estado.
Reclamaciones
Si
la caja o el contenido (el producto y los accesorios incluidos) parecen dañados a
causa del transporte o muestran signos de manipulación inadecuada, notifíqueselo
inmediatamente al transportista, y no a CHAUVET®. Si no lo hace oportunamente,
puede quedar i
nvalidada su reclamación al transportista. Además, guarde la caja y todo
el material de embalaje para su inspección.
Para otras incidencias, como componentes o piezas que falten, daños no relacionados
con el transporte o daños no evidentes, presente una re
clamación a CHAUVET® en el
plazo de 7 días de la entrega.
Convenciones
del Manual
Convención Significado
1—512
Un rango de valores
50/60
Un conjunto de valores de los cuales solo se pude escoger uno
Configuración
Una opción de menú que no se puede modificar
Menú >
Configuración
Una secuencia de opciones de menú que ha de seguirse
<ENTER>
Una tecla que se tiene que pulsar en el panel de control del
producto
ON
Un valor que se tiene que introducir o seleccionar
Símbolos
Símbolo Significado
Instalación, configuración o información sobre funcionamiento
crítica. Hacer caso omiso de esta información puede hacer que el
producto no funcione, que se averíe, o causar daños al usuario.
Instalación o información de configuración importante. El producto
puede no funcionar correctamente si esta información no se usa.
Información útil.
Exención de
Responsa-
bilidad
La información y especificaciones contenidas en este documento están sujetas a
cambio sin previo aviso. CHAUVET® no asume responsabilidad de ningún tipo por
cualquier error u omisión que pueda aparecer en este manual, y se reserva el derecho a
revisar o re
hacer este manual en cualquier momento. Descargue la última versión de
www.chauvetlighting.com.
© Copyright 2013 CHAUVET®. Todos los derechos reservados.
Impreso en la R. P. China.
Publicación en formato electrónico por CHAUVET® en EE.UU.

EZMiN™ Laser FX/RBX Manual de Usuario Rev. 3 Página 19 de 48
Notas de
Seguridad
Las Notas de seguridad incluyen información importante sobre seguridad del
sistema láser. Lea y comprenda todas las instrucciones antes de encender el
láser por primera vez. Conocer las
instrucciones de seguridad es crucial para
evitar lesiones oculares y para no infringir la ley. Mantenga este manual de
usuario en un lugar seguro para futuras consultas.
DETÉNGASE Y LEA TODOS LOS DATOS DE SEGURIDAD
•Los láseres pueden ser peligrosos y tienen consideraciones de seguridad
particulares. Puede producirse lesión ocular permanente y ceguera si los
láseres se usan incorrectamente. Ponga máxima atención a todos los
COMENTARIOS y ADVERTENCIAS de seguridad de este manual de usuario.
Lea atentamente todas las instrucciones ANTES de poner en funcionamiento
este dispositivo.
•Conecte siempre el producto a un circuito con toma de tierra para evitar el riesgo de
electrocución.
•Desconecte siempre el producto de la alimentación antes de limpiarlo.
•Evite la exposición directa de los ojos a la fuente de luz mientras es producto esté
encendido.
•Asegúrese de que el cable de alimentación no está retorcido ni estropeado.
•Nunca desconecte este producto de la alimentación agarrando o tirando del cable.
•Si monta el producto en alto, asegure siempre a un dispositivo de seguridad usando
cable de seguridad.
•Asegúrese de que no hay materiales inflamables cerca del producto cuando esté en
funcionamiento.
•No toque la carcasa del producto cuando esté en funcionamiento, porque podría
estar muy caliente.
•No quite el soporte en ningún momento. Este producto está concebido para usarse
con este soporte.
•
Este producto no está concebido para una instalación permanente.
•Asegúrese siempre de que la tensión del enchufe al que conecte el producto está en
el rango establecido en el grabado o en el panel posterior del producto.
•¡El producto es para uso en interiores solamente! (IP20) Para evitar riesgos de
incendio o descarga, no exponga el producto a la lluvia o la humedad.
•Instale siempre el producto en una ubicación con ventilación adecuada, al menos a
20'' (50 cm) de superficies adyacentes.
•Asegúrese de que ninguna ranura de ventilación en la carcasa del producto queda
bloqueada.
•Nunca conecte el producto a un atenuador.
•Use siempre el soporte de montaje para trasladar el producto.
•No Apague/Encienda el producto a intervalos cortos. Esto acortará la vida del diodo
láser.
•NO sacuda este producto. Evite usar la fuerza bruta cuando monte o maneje el
producto.
•Use SIEMPRE un cable de seguridad cuando monte este producto en lo alto.
•La temperatura ambiente (Ta) máxima es de 40 °C (104 °F). No haga funcionar el
producto a temperaturas más altas.
•En caso de un problema grave de funcionamiento, deje de usar el producto
inmediatamente.
•
Nunca intente reparar el producto. Las reparaciones llevadas a cabo por personal no
cualificado pueden provocar averías o funcionamiento defectuoso. Póngase en
contacto con el centro de asistencia técnica autorizado más cercano.

Página 20 de 48 EZMiN™ Laser FX/RBX Manual de Usuario Rev. 3
•Evite el contacto directo de los ojos con la luz del láser. Nunca exponga
intencionadamente sus ojos o los de otras personas a la luz directa del láser.
•Este producto láser puede causar lesiones oculares al instante, o ceguera, si la luz
del láser incide directamente en los ojos.
•Es ilegal y peligroso alumbrar con este láser zonas de espectadores en las que el
público u otro personal pueda recibir rayos láser o reflejos de su brillo directamente
en los ojos.
•En los EEUU es un delito federal dirigir cualquier láser hacia un avión.
•El uso de controles, ajustes o procedimientos distintos a los especificados en este
manual de usuario pueden causar exposición peligrosa a la radiación.
•NO intente ninguna reparación. Las reparaciones y la asistencia deben ser llevadas
a cabo por un técnico autorizado. ¡Las modificaciones no autorizadas están
prohibidas por motivos de seguridad!
•Guarde este manual de usuario para futuras consultas. Si este producto pasa a ser
propiedad de otro usuario, asegúrese de que este documento acompaña al láser.
Advertencia
sobre Carcasa no
Cerrada
•Esta unidad contiene internamente dispositivos láser de alta potencia.
•No abra la carcasa del láser, debido a la potencial exposición a niveles no seguros
de radiación láser.
•Los niveles de láser a los que se tiene acceso si se abre la unidad pueden causar
ceguera instantánea, quemaduras en la piel e incendios.
Notas de
Seguridad s
obre
Láser
DETÉNGASE Y LEA TODAS LAS NOTAS DE SEGURIDAD
SOBRE EL LÁSER SIGUIENTES
La luz láser es diferente de cualquier otra fuente de luz. La luz de este producto puede
causar lesión ocular si el producto no se instala y usa adecuadamente. La luz láser es
miles de veces más concentrada que la luz de cualquier otro tipo de fuente. Esta
concentración de luz puede causar lesiones instantáneas en el ojo, fundamentalmente
por quemadura de la retina (la zona sensible a la luz en la parte posterior del ojo).
Aunque usted no pueda sentir el “calor” de un haz de láser, este puede aún
potencialm
ente lesionar o cegarle a usted o al público. Incluso cantidades de luz láser
muy pequeñas son potencialmente peligrosas, incluso a largas distancias. Las lesiones
oculares por láser pueden ocurrir más rápido de lo que se tarda en parpadear.
NO dé por supu
esto que porque estos productos recreativos de láser dividan el láser en
cientos de haces, y porque el haz de láser se lance a alta velocidad, es segura la
exposición del ojo a un haz individual de láser. Este producto de láser utiliza docenas de
milivatio
s de potencia láser (niveles clase 3B internamente) antes de dividirlo en
múltiples haces (niveles clase 3R). Muchos de los haces individuales son
potencialmente peligrosos para los ojos.
NO asuma que porque la luz láser está en movimiento, es segura. La
luz láser no está
nunca libre de riesgo, ni aunque el haz se mueva siempre. Puesto que las lesiones oculares
pueden producirse instantáneamente, es crítico prevenir la posibilidad de CUALQUIER
exposición directa al ojo. Según las disposiciones de seguridad
láser, no es legal apuntar
con láseres Clase 3a hacia áreas en las que las personas puedan quedar expuestas. Esto
se aplica incluso si se apunta con el láser por debajo de las caras de la gente, por ejemplo
hacia la pista de baile.