Chauvet FX 350 User manual

User Manual

Page 2 of 20 Intimidator™ FX 350 User Manual Rev. 1
TABLE OF CONTENTS
1. Before You Begin.......................................................................................................... 3
What Is Included...............................................................................................................................3
Unpacking Instructions.....................................................................................................................3
Claims ....................................................................................................................................................... 3
Text Conventions .............................................................................................................................3
Symbols............................................................................................................................................3
Disclaimer.........................................................................................................................................3
Product at a Glance..........................................................................................................................4
Safety Notes.....................................................................................................................................4
2. Introduction................................................................................................................... 5
Overview...........................................................................................................................................5
Dimensions.......................................................................................................................................6
3. Setup.............................................................................................................................. 7
AC Power .........................................................................................................................................7
Fuse Replacement .................................................................................................................................... 7
Power Linking............................................................................................................................................ 8
Mounting...........................................................................................................................................9
Orientation................................................................................................................................................. 9
Rigging...................................................................................................................................................... 9
4. Operation......................................................................................................................10
Control Panel Operation.................................................................................................................10
Menu Map.......................................................................................................................................10
Configuration (DMX).......................................................................................................................10
Starting Address...................................................................................................................................... 10
DMX Personalities................................................................................................................................... 10
DMX Channel Modes, Assignments, and Values ..........................................................................11
15-Channel.............................................................................................................................................. 11
15-Channel (cont.)................................................................................................................................... 12
15-Channel (cont.)................................................................................................................................... 13
7-Channel................................................................................................................................................ 13
7-Channel (cont.)..................................................................................................................................... 14
Configuration (Standalone) ............................................................................................................15
Sound-Active Mode................................................................................................................................. 15
Automatic Mode....................................................................................................................................... 15
Manual Pan/Tilt Operation....................................................................................................................... 15
Manual Pan/Tilt Angle Range.................................................................................................................. 15
Display..................................................................................................................................................... 15
Master/Slave Mode.................................................................................................................................. 16
Reset Software...............................................................................................................................16
Factory Defaults .............................................................................................................................16
5. Technical Information..................................................................................................17
Product Maintenance .....................................................................................................................17
6. Technical Specifications..............................................................................................18
Returns .............................................................................................................................19
Contact Us........................................................................................................................20

Intimidator™ FX 350 User Manual Rev. 1 Page 3 of 20
1.BEFORE YOU BEGIN
What Is
Included
•Intimidator™ FX 350
•Hanging bracket with mounting
hardware
•Power cord
•Warranty card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately
and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and
included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as
missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Text
Conventions
Convention Meaning
1–512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this User Manual
are subject to change
without notice. CHAUVET® assumes no responsibility or liabil
ity for any errors or
omissions,
and reserves the right to revise or recreate this manual at any time.
Download the latest version from www.chauvetlighting.com.
© Copyright 2014 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author Date Editor Date
A. Leon 02/04/14 L. Henry 02/13/14

Page 4 of 20 Intimidator™ FX 350 User Manual Rev. 1
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Activated
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
These notes include important i
nformation about the mounting, usage, and maintenance
of this product; read before using the product.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Contact the nearest authorized technical assistance center.
•
This product is not intended for permanent installation.
Keep this User Manual for future use. If you sell the product to another user, be sure to
give this document to the next owner.

Intimidator™ FX 350 User Manual Rev. 1 Page 5 of 20
2.INTRODUCTION
Overview
Front Panel View
Display
Control
Buttons
Back Panel View
Power In
Fuse Holder
Power Out
DMX Out
DMX In
Safety Loop

Page 6 of 20 Intimidator™ FX 350 User Manual Rev. 1
Dimensions
15.4 in
392 mm
13.4 in
340 mm
9.8 in
248 mm

Intimidator™ FX 350 User Manual Rev. 1 Page 7 of 20
3.SETUP
AC Power
The Intimidator™ FX 350 has an auto-
ranging power supply and it can work with an
input voltage range of 100–240 VAC, 50/60 Hz.
To determine the product’s power requirements (
circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product
’s back panel, or
refer to the product
’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit
(circuit breaker or fuse). Make
sure the product
has an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product
to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
Disconnect the product from power before replacing the fuse.
1. Disconnect the product from power.
2. Use a flathead screwdriver to unscrew the fuse holder cap
from the housing.
3. Remove the blown fuse.
4. Replace with a fuse of the same type and rating.
5. Screw the fuse holder cap back in place and reconnect
power.
Always replace a blown fuse with another of the same type and rating.

Page 8 of 20 Intimidator™ FX 350 User Manual Rev. 1
Power Linking
The product
provides power linking via the Edison/IEC outlet located in the front/back of
the unit.
Power Linking
Diagram
You can power link up to 3 Intimidator™ FX 350 unit
s on 120 VAC or up to
7 Intimidator™ FX 350 units on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product
in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
1st Product
2nd Product
3rd Product
Additional Products

Intimidator™ FX 350 User Manual Rev. 1 Page 9 of 20
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes. For our CHAUVET® line of mounting
clamps, go to
www.chauvetlighting.com/cables-clamps-main.html/.
Orientation
The Intimidator™ FX 350
may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
•Before deciding on a location, always make sure there is easy access to the product
for maintenance and programming.
•Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight (see the Technical Specifications).
•When mounting the product overhead, always use a safety cable (such as CH-05
from CHAUVET®). Mount the product securely to a rigging point, such as an
elevated platform or a truss.
•When rigging the product onto a truss, you should use mounting clamps
(such as
CLP-15 from CHAUVET®) of appropriate weight capacity. The bracket has 13-mm
holes, which are appropriate for this purpose.
•When power linking multiple products, you must
always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
•The mounting bracket also allows for surface mounting. When mounting the product
on the floor, make sure that the product and cables are a
way from people and
vehicles.
Mounting Diagram
When using only one mounting clamp with this fixture, you must use a clamp with a
captive bolt to prevent accidental loosening.
Mounting
Clamps
Safety
Cable
Hanging/
Mounting
Bracket
Rubber Feet
(x4) for floor
mounting

Page 10 of 20 Intimidator™ FX 350 User Manual Rev. 1
4.OPERATION
Control Panel
Operation
To
access the control panel functions, use the four buttons located underneath the
display.
Button Function
<MENU> Selects an operation mode or backs out of the current menu option
<UP> Scrolls up the list of options or selects a higher value
<DOWN> Scrolls down the list of options or selects a lower value
<ENTER> Activates a menu option or a selected value
Menu Map
Mode Programming Levels Description
DMX Mode
d001–d512
Sets the DMX starting address
Operating Mode
NASL (SLoU)
Automatic mode, slow program
NAFA (FASt)
Automatic mode, fast program
NStS (SrUn)
Sound-Active mode
SLAv (Son)
Slave operating mode
Pan
PAn
Normal pan operation
rPAn
Inverse pan operation
Tilt
tit
Normal tilt operation
rtit
Inverse tilt operation
Display
diS
Normal display
rdiS
Inverse display
Channel Mode
15CH
Selects the 15-channel DMX personality
7CH
Selects the 7-channel DMX personality
Manual Pan
Range
PA54
Selects the 540° pan angle range
PA36
Selects the 360° pan angle range
PA18
Selects the 180° pan angle range
Manual Tilt
Range
ti27
Selects the 270° tilt angle range
ti18
Selects the 180° tilt angle range
ti 9
Selects the 90° tilt angle range
Reset
rESt
Resets fixture
Load
LoAd
Load factory defaults
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
on the product.
Starting Address
When
selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you
choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The Intimidator™ FX 350 uses up to 15 DMX channels in its 15-channel
personality,
which defines the highest configurable address to 498.
If unfamiliar with DMX, download the DMX Primer from www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU>repeatedly until d001–d512 shows on the display.
2. Use <UP> or <DOWN> to select the starting address.
3. Press <ENTER>.
DMX
Personalities
The Intimidator™ FX 350 has two DMX personalities, a 7-channel personality and a 15-
channel personality.
To choose which DMX personality to use, follow the steps below:
1. Press <MENU> repeatedly until either 15CH (to choose the 15-
channel personality)
or 7CH (to choose the 7-channel personality) shows on the display.
2. Use <UP> or <DOWN> to select the desired personality.
3. Press <ENTER>.

Intimidator™ FX 350 User Manual Rev. 1 Page 11 of 20
DMX Channel Modes, Assignments, and Values
15-Channel
Channel Function Value Setting
1
Pan
000 ó255
0–540°
2
Fine Pan
000 ó255
Fine control of panning
3
Tilt
000
ó
255
0–270°e
4
Fine Tile
000 ó255
Fine control of tilting
5
Speed
000 ó255
Pan/Tilt speed (fast to slow)
6 Color Wheel
000 ó006
007 ó013
014 ó020
021 ó027
028 ó034
035 ó041
042 ó048
049 ó055
056 ó063
064 ó070
071 ó077
078 ó084
085 ó091
092 ó098
099 ó105
106 ó112
113 ó119
120 ó127
128 ó191
192 ó255
White
Yellow
Pink
Green
Red
Light Blue
Kelly
Orange
Dark Blue
White + Yellow
Yellow + Pink
Pink + Green
Green + Red
Red + Light Blue
Light Blue + Kelly
Kelly + Orange
Orange + Dark Blue
Dark Blue + White
Color cycling rainbow with increasing speed
Reverse color cycling rainbow with increasing
speed
7 Prism
000 ó255
000 ó255
000 ó255
000 ó255
000 ó255
Open
Prism effect
Prism rotation with increasing speed
Reverse prism rotation with increasing speed
Prism effect
8
Dimmer
000 ó255
0–100%
9 Shutter
000 ó003
004 ó007
008 ó076
077 ó145
146 ó215
216 ó255
Closed
Open
Strobe with increasing speed
Pulse strobe
Random shutter
Open
10 Control Functions
000 ó007
008 ó015
016 ó023
024 ó031
032 ó039
040 ó047
048 ó055
056 ó087
088 ó095
096 ó103
104 ó111
112 ó119
120 ó127
128 ó135
136 ó143
144 ó151
152 ó159
160 ó255
No function
Blackout while panning/tilting
Blackout while moving color wheel
Blackout while moving light patterns
Disable blackout while panning/tilting/
moving color wheel
Disable blackout while panning/tilting/
moving light patterns
Disable blackout while moving all options
Reserved for future use
Reserved for future use
Reset pan
Reset tilt
Reset color wheel
Reset light patterns
Reserved for future use
Reset prism
Reserved for future use
Reset all channels
No function

Page 12 of 20 Intimidator™ FX 350 User Manual Rev. 1
15-Channel
(cont.)
Channel Function Value Setting
11 Movement Macros
000 ó007
008 ó023
024 ó039
040 ó055
056 ó071
072 ó087
088 ó103
104 ó119
120 ó135
136 ó151
152 ó167
168 ó183
184 ó199
200 ó215
216 ó231
232 ó247
248 ó255
No function
Automatic movement 1
Automatic movement 2
Automatic movement 3
Automatic movement 4
Automatic movement 5
Automatic movement 6
Automatic movement 7
Automatic movement 8
Sound-Active movement 1
Sound-Active movement 2
Sound-Active movement 3
Sound-Active movement 4
Sound-Active movement 5
Sound-Active movement 6
Sound-Active movement 7
Sound-Active movement 8
12 Light Patterns
000 ó007
No function

Intimidator™ FX 350 User Manual Rev. 1 Page 13 of 20
15-Channel
(cont.)
Channel Function Value Setting
12 (cont.)
Light Patterns (cont.)
240 ó255
Automatic effect pattern
13
Speed
000 ó255
Light patterns speed, slow to fast
14 Effect Motor 1
000
001 ó127
128 ó255
No function
Forward, slow to fast
Inverted, slow to fast
15 Effect Motor 2
000
001 ó127
128 ó255
No function
Forward, slow to fast
Inverted, slow to fast
7-Channel
Channel Function Value Setting
1
Pan
000 ó255
0–540°
2
Tilt
000 ó255
0–270°e
3 Color Wheel
000 ó006
007 ó013
014 ó020
021 ó027
028 ó034
035 ó041
042 ó048
049 ó055
056 ó063
064 ó070
071 ó077
078 ó084
085 ó091
092 ó098
099 ó105
106 ó112
113 ó119
120 ó127
128 ó191
192 ó255
White
Yellow
Pink
Green
Red
Light Blue
Kelly
Orange
Dark Blue
White + Yellow
Yellow + Pink
Pink + Green
Green + Red
Red + Light Blue
Light Blue + Kelly
Kelly + Orange
Orange + Dark Blue
Dark Blue + White
Color cycling rainbow with increasing speed
Reverse color cycling rainbow with increasing
speed
4 Prism
000 ó255
000 ó255
000 ó255
000 ó255
000
ó
255
Open
Prism effect
Prism rotation with increasing speed
Reverse prism rotation with increasing speed
Prism effect

Page 14 of 20 Intimidator™ FX 350 User Manual Rev. 1
7-Channel
(cont.)
Channel Function Value Setting
5 Shutter
000 ó003
004 ó007
008 ó076
077 ó145
146 ó215
216 ó255
Closed
Open
Strobe with increasing speed
Pulse strobe
Random shutter
Open
6 Light Patterns
000 ó007
No function
240 ó255
Automatic effect pattern
7
Speed
000 ó255
Light patterns speed, slow to fast

Intimidator™ FX 350 User Manual Rev. 1 Page 15 of 20
Configuration
(Standalone)
Set the product in one of the standalone modes to control it without a DMX controller.
Connect the product to a suitable power outlet.
Never connect a product that is operating in any standalone mode (
Static,
Automatic, or Sound-Active)
to a DMX string connected to a DMX controller.
Product
s in standalone mode may transmit DMX signals that could interfere with
the DMX signals from the controller.
Sound-Active
Mode
To enable the Sound-Active mode, do the following:
1. Press <MENU>repeatedly until one of the following shows on the display:
NASL, NAFA, NStS, SLAv
2. Use <UP> or <DOWN> to select NStS.
3. Press <ENTER> and SrUn shows on the display.
The product will only respond to low frequencies of music (bass and drums).
Automatic Mode
To enable the Automatic mode, do the following:
1. Press <MENU> repeatedly until one of the following shows on the display:
NASL, NAFA, NStS, SLAv
2. Use <UP> or <DOWN> to select NASL (for a slow light show) or NAFA (for a fast
light show).
3. Press <ENTER> and SLou shows on the display for the slow light show or
FASt shows on the display for the fast light show.
Manual Pan/Tilt
Operation
To select whether you want the Intimidator™
FX 350 to operate with normal panning or
inverted (reverse) panning, do the following.
1. Press <MENU> repeatedly until PAn or rPAn shows on the display.
2. Use <UP> or <DOWN> to select normal pan operation (PAn) or inverted pan
operation (rPAn).
3. Press <ENTER>.
To select whether you want the Intimidator™
FX 350 to operate with normal tilting or
inverted (reverse) tilting, do the following:
1. Press <MENU> repeatedly until tit or rtit shows on the display.
2. Use <UP> or <DOWN> to select normal pan operation (tit) or inverted pan
operation (rtit).
3. Press <ENTER>.
Manual
Pan/Tilt
Angle Range
To select the range for the pan and tilt angles on the Intimidator™
FX 350, do the
following:
1. Press <MENU> repeatedly until PA54, PA36, or PA18 shows on the display.
2. Use <UP> or <DOWN> to select 540° (PA54), 360° (PA36), or 180° (PA18).
3. Press <ENTER>.
To select which tilt angle range to use, do the following:.
1. Press <MENU> repeatedly until Ti27, Ti18, or Ti 9shows on the display.
2. Use <UP> or <DOWN> to select 270° (Ti27), 180° (Ti18), or 90° (Ti 9).
3. Press <ENTER>.
Display
You can flip the LED display for easy readability in any mounting situation.
To select your display angle:
1. Press <MENU> repeatedly until diS or rdiS shows on the display.
2. Use <UP> or <DOWN> to select normal display mode (diS) or inverted display
mode (rdiS).
3. Press <ENTER>.

Page 16 of 20 Intimidator™ FX 350 User Manual Rev. 1
Master/Slave
Mode
The Master/Slave mode allows a single Intimidator™ FX 350
unit (the master) to control
the actions of one or more Intimidator™ FX 350
units (the slaves) without a DMX
controller. The master unit operates in either Automatic or Sound-
Active mode, while the
slave units operate in Slave m
ode. Once set and connected, the slave units will operate
in unison with the master unit.
Configure the units as described below.
Slave units:
1. Press <MENU>repeatedly until SLAv shows on the display.
2. Press <ENTER> to accept and Son will show on the display.
3. Set the DMX address to 001.
4. Connect the DMX input of the first slave unit to the DMX output of the master unit.
5. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
6. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in either Automatic or Sound-Active mode.
2. Make the master unit the first unit in the DMX daisy chain.
•Configure
all the slave units before connecting the master unit to the DMX
daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller
may interfere with the signals from the
master unit.
•Do not connect more than 31 slave units to the master unit.
Reset
Software
To reset the software on the Intimidator™ FX 350, do the following:
1. Press <MENU> repeatedly until rESt shows on the display.
2. Press <ENTER>. The product will reset all settings in the software.
Factory
Defaults
To load the factory defaults on the Intimidator™ FX 350, do the following:
1. Press <MENU> repeatedly until LoAd shows on the display.
2. Press <ENTER>. The product resets to factory default settings.

Intimidator™ FX 350 User Manual Rev. 1 Page 17 of 20
5.TECHNICAL INFORMATION
Product
Maintenance
Dust build-
up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and mechanical wear.
To maintain optimum
performance and minimize wear, clean the product at least twice a month. However,
usage and environmental conditions contribute to increased cleaning frequency.
To clean the product, follow the instructions below:
•Unplug the product from power.
•Wait until the product is at room temperature.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
•Clean all external optics and glass/transparent surfaces with a mild soap solution,
ammonia-free glass cleaner, or isopropyl alcohol.
•Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
•Softly wipe any dirt or grime to the outside edges of the external optics or
glass/transparent surface.
•Gently polish the external optics and glass/transparent surfaces until they are free of
haze and lint.
Always dry the external optics and glass/transparent
surfaces carefully after
cleaning them.
Do not spin the cooling fan/fans using compressed air
because you could damage
it/them.

Page 18 of 20 Intimidator™ FX 350 User Manual Rev. 1
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
13.4 in (340 mm)
9.8 in (248 mm)
15.4 in (392 mm)
24.4 lb (11.2 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100 to 240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
239 W
251 W
Operating current
1 A
1 A
Power linking current (units)
8 A (3 units)
8 A (7 units)
Fuse
F 3 A, 250 V
F 3 A, 250 V
Power I/O
US/Canada
UK/Worldwide
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (US)
Local plug
Light Source
Type
Power
Lifespan
LED
75 W
50,000 hours
Color
Quantity
Current
White
1
17 A
Photo Optic
Parameter
Illuminance @ 2 m
18,830 lx
Beam angle
8°
Strobe rate
0 to 20 Hz
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Fan-cooled
DMX
I/O Connectors
Connection Type
Channel Range
3-pin XLR
Sockets
7 or 15
Ordering
Product Name
Item Code
UPC Number
Intimidator™ FX 350
08010754
781462211028

Intimidator™ FX 350 User Manual Rev. 1 Page 19 of 20
R
ETURNS
To return a product or request support:
•In the U.S., contact CHAUVET® World Headquarters (see below).
•In the UK or Ireland, contact CHAUVET® Europe Ltd. (see below).
•In Mexico, contact CHAUVET® Mexico (see below).
In any other country, DO NOT contact CHAUVET®. Contact your distributor. See
www.chauvetlighting.com for distributors outside the U.S., United Kingdom, Ireland, or Mexico.
If you live outside the U.S., United Kingdom, Ireland, or Mexico, contact your distributor of
record and follow their instructions on how to return CHAUVET® products to them. Visit our
website for contact details.
Call the corresponding CHAUVET® Technical Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide
the model number, serial number, and a brief description of the cause for the return.
You must send the merchandise prepaid, in its original box, and with its original packing and
accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product returned
without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number directly on
the box.
Before sending the product, clearly write the following information on a piece of paper and place
it inside the box:
1. Your name
2. Your address
3. Your phone number
4. RMA number
5. A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. FedEx packing or double-boxing are recommended.
CHAUVET® reserves the right to use its own discretion to repair or replace returned
product(s).

Page 20 of 20 Intimidator™ FX 350 User Manual Rev. 1
C
ONTACT
US
WORLD HEADQUARTERS - CHAUVET®
General Information
Address:5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free:[phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
World Wide Web www.chauvetlighting.com
UNITED KINGDOM AND IRELAND - CHAUVET® Europe Ltd.
General Information
Address:Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Email: [e-mail]
World Wide Web www.chauvetlighting.co.uk
MEXICO - CHAUVET® Mexico
General Information
Address:Av. Santa Ana 30
Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Voice: [phone]
Technical Support
Email: [email protected]
World Wide Web www.chauvet.com.mx
Outside the U.S., United Kingdom, Ireland, or Mexico, contact your dealer. Follow their
instructions to request support or to return a product. Visit our website for contact details.