Chauvet Legend 230SR Beam User manual

User Manual

Edition Notes
ii Legend™ 230SR Beam User Manual Rev. 1
Edition Notes
The Legend™ 230SR Beam User Manual Rev. 1 covers the description, safety
precautions, installation, programming, operation, and maintenance of the
Legend™
230SR Beam. CHAUVET® released this edition of the Legend™ 230SR Beam
User
Manual in August 2012.
Trademarks
CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or
Chauvet). The CHAUVET® logo in its entirety including the Chauvet name and
the
dotted triangle, and all other trademarks on this manual pertaining to services, products,
or marketing statements (example: It’s Green Thinking™
) are owned or licensed by
CHAUVET®. Any other
product names, logos, brands, company names, and other
trademarks featured or referred to within this document are the property of their
respective trademark holders.
Copyright Notice
CHAUVET® owns the content of this user manual in its entirety, including but not limited
to pictures, logos, trademarks, and resources.
© Copyright 2012 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Manual Usage
CHAUVET® authorizes its customers to download and print this manual for professional
information purposes only. CHAUVET® expressly prohibits the u
sage, copy, storage,
distribution, modification, or printing of this manual or its content for any other purp
ose
without its written consent.
Document Printing
For best results, print this document in color, on letter size paper (8.5 x 11 inches),
double sided. If using A4 paper (210 x 297 mm), configure your printer to scale the
content accordingly.
Disclaimer
CHAUVET® believes that the information contained in this manual is accurate in all
respects. However, CHAUVET® assumes no responsibility for any error or omissions in
this document. CHAUVET® reserves the right to revise this document and to make
changes from time to time in the content hereof without obligation of CHAUVET® to
notify any person or company of such revision or changes. This does not constitute in
any way a commitment by CHAUVET® to make such changes. CHAUVET® may issue
a revision of this manual or a new edition of it to incorporate such changes.
Document Revision
The Legend™ 230SR Series User Manual, Rev. 1, supersedes all previous versions of
this manual. Please discard any older versions
of this manual you may have, whether in
printed or electronic format, and replace them with this version.
Author Date Editor Date
D. Couppe
9/13/12
S. Diaz
9/24/12

Table of Contents
Legend™ 230SR Beam User Manual Rev. 1 -iii-
Table of Contents
1. Before You Begin ...................................................................................................................................... 1
What Is Included...................................................................................................................................................................1
Claims..................................................................................................................................................................................1
Manual Conventions .............................................................................................................................................................1
Symbols ...............................................................................................................................................................................1
Product at a Glance...................................................................................................................................................2
Safety Notes..............................................................................................................................................................2
Personal Safety ....................................................................................................................................................................2
Mounting and Rigging ........................................................................................................................................................... 2
Power and Wiring .................................................................................................................................................................2
Operation .............................................................................................................................................................................2
2. Introduction ............................................................................................................................................... 3
Product Description ...................................................................................................................................................3
Features....................................................................................................................................................................3
Product Overview ......................................................................................................................................................4
Product Dimensions ..................................................................................................................................................5
3. Setup.......................................................................................................................................................... 6
AC Power ..................................................................................................................................................................6
AC Plug................................................................................................................................................................................6
Fuse Replacement................................................................................................................................................................6
DMX Linking..............................................................................................................................................................6
DMX Modes..........................................................................................................................................................................6
Gobo Wheel ..............................................................................................................................................................7
Color Wheel ..............................................................................................................................................................7
Lamp Replacement ...................................................................................................................................................8
Procedure.............................................................................................................................................................................8
Increasing the Lamp’s Life ....................................................................................................................................................9
Mounting .................................................................................................................................................................10
Orientation.......................................................................................................................................................................... 10
Rigging............................................................................................................................................................................... 10
4. Operation ................................................................................................................................................. 11
Control Panel Description ........................................................................................................................................11
LCD Display ............................................................................................................................................................11
Control Options .......................................................................................................................................................11
Programming......................................................................................................................................................................11
Navigation Buttons.............................................................................................................................................................. 11
DMX Functions ...................................................................................................................................................................11
Product Settings ................................................................................................................................................................. 12
Lamp Settings ....................................................................................................................................................................12
Display Settings..................................................................................................................................................................13
Fixture Tests....................................................................................................................................................................... 14
Fixture Information.............................................................................................................................................................. 14
Reset Functions..................................................................................................................................................................14
Special Functions ............................................................................................................................................................... 15
Offset Mode.............................................................................................................................................................15
Entering Offset Mode .......................................................................................................................................................... 15
Menu Map ...............................................................................................................................................................17
Menu Map (cont.) ....................................................................................................................................................18
DMX Values ............................................................................................................................................................19

Table of Contents
iv Legend™ 230SR Beam User Manual Rev. 1
DMX Values (cont.) .................................................................................................................................................20
DMX Values (cont.) .................................................................................................................................................21
DMX Values (cont.) .................................................................................................................................................22
DMX Values (cont.) .................................................................................................................................................23
5. Technical Information ............................................................................................................................. 24
Product Maintenance...............................................................................................................................................24
Returns ...................................................................................................................................................................24
Error Messages .......................................................................................................................................................25
6. Technical Specifications......................................................................................................................... 26
Contact Us ..............................................................................................................................................................27

Before You Begin
Legend™ 230SR Beam User Manual Rev. 1 1
1. Before You Begin
What Is Included
•Legend™ 230SR Beam
•2 Omega Brackets
•Warranty Card
•Quick Reference Guide
Claims
Carefully unpack the product immediately and check the box to make sure all the parts
are in the package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from
shipping or show signs of mishandling, notify the carrier immediate
ly, not CHAUVET®.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Manual Conventions
Convention
Meaning
1~512
A range of values in the text
50/60
A set of mutually exclusive values in the text
<SET>
A button on the product’s control panel
Settings
A product function or a menu option
MENU>Settings
A sequence of menu options
1~10
A range of menu values from which to choose in a menu
Yes/No
A set of two mutually exclusive menu options in a menu
ON
A unique value to be entered or selected in a menu
Symbols
Symbols Meaning
Critical installation, configuration, or operation information.
Failure to comply with this information may
cause the product not
to work, damage third-party equipment, or cause harm to the
operator.
Important installation or configuration information. Failure to
comply with this information may keep the product from working.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-A
digital data transmission protocol.

Before You Begin
2 Legend™ 230SR Beam User Manual Rev. 1
Product at a Glance
Use on Dimmer

Auto Programs

Outdoor Use

Auto-Ranging Power
Supply

Sound Activated

Replaceable Fuse

DMX

User Serviceable

Master/Slave

Duty Cycle

Product must be placed so that any objects being hit by the beam of light are at
least 40 feet (12.2 meters) away!
Safety Notes
Please read the following Safety Notes carefully before starting to work with the product.
These notes provide important safety information about the installation, usage,
and
maintenance.
This product contains no user-serviceable parts. Any reference to servicing in this
User Manual will only apply to properly trained CHAUVET® certified technicians.
Do not open the housing or attempt any repairs.
Please refer to all applicable local codes and regulations for the proper installation
of the product.
Personal Safety
•Avoid direct eye exposure to the light source while the product is on.
•Do not turn product on without a lamp!
•Always disconnect this product from its power source before servicing.
•Always connect this product to a grounded circuit to avoid the risk of electrocution.
•Do not touch this product’s housing during operation because it may be very hot.
Mounting and Rigging
•This product is for indoor use only! To prevent risk of fire or shock, do not expose this
product to rain or moisture.
•This product weighs 41.3 lbs (18.73 kg). Always ask for help when mounting this
product to avoid personal injuries or damage to the product.
•Make sure there are no flammable materials close to this product while it is operating.
•When hanging this product, always secure to a fastening device using a safety cable
(included).
•Always carry this product by the handles. Do not carry from the head.
Power and Wiring
•Always make sure you are connecting this product to the proper voltage in
accordance with the specifications in this manual or on the product’s specification
label.
•Never connect this product to a dimmer pack or rheostat.
•
Never disconnect this product by pulling or tugging on the power cable.
Operation
•Do not operate this product if you see damage on the housing, lenses, ultraviolet
filter, or cables. Have the damaged parts replaced by an authorized technician at
once.
•Do not cover the ventilation slots when operating to avoid internal overheating.
•Do not aim this product toward the Sun. The lenses could concentrate the solar
energy and cause internal overheating.
•Do not aim this product toward fire sprinkler head or alarms. The beam could heat up
the sensors causing them to go off.
•Mount this product in a location with adequate ventilation, at least 40 ft. (12.2 m) from
objects to be lit.
•The maximum ambient temperature is 104° F
(40° C). Do not operate this product at a
higher temperature.
•
In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your CHAUVET® product may require service, contact
CHAUVET® Technical Support.

Introduction
Legend™ 230SR Beam User Manual Rev. 1 3
2. Introduction
Product
Description
The Legend™ 230SR Beam is a compact, electronic, moving-yoke beam product equipped
with a 230W-watt HID lamp. It includes a color wheel with 14 slots plus white. It
also comes
with one gobo wheel with 17 static gobos plus open, remote focus, and a rotating 8-
facet
prism.
Features
•Compact, moving-yoke beam fixture with a zoomable prism and motorized focus
•Uses Osram Sirius 230 W lamp source with a rated 3,000-hour lamp life
•Precision designed optics for hard-edged beam effects
•Extremely quiet for operation in any situation
•Fast and precise pan/tilt
•Color wheel:
•14 colors + Open
•CTO - Split/linear colors
•Rainbow color spin at variable speed
•Gobo wheel:
•17 gobos + Open
•Gobo wheel spin at variable speed
•Variable frost
•8-facet rotating prism with zoom for stunning effects
•Lightweight and easy to hang
•DMX channels: 15 or 18
•Pan: 540°
•Tilt: 270°
•Reset over DMX
•Electronic power supply
•Mechanical dimmer
•3- and 5-pin DMX input and output connectors

Introduction
4 Legend™ 230SR Beam User Manual Rev. 1
Product Overview
Handles
Control Panel
Mounting Base
Front Glass Lens
Rubber Feet
¼-Turn Cover
Fasteners For
Easy Acess
Power In

Introduction
Legend™ 230SR Beam User Manual Rev. 1 5
Product Dimensions

Setup
6 Legend™ 230SR Beam User Manual Rev. 1
3. Setup
AC Power
Each Legend™ 230SR Beam has an auto-ranging power supply that works with an input
voltage range of 100~240 VAC, 50/60 Hz.
To determine the power requirements for
each Legend™ 230SR Beam, refer to the label affixed to the product. You can also refer
to the Technical Specifications.
The listed current rating indicates the maximum current draw during normal operation.
For more information, you may download Sizing Circuit Breakers from the CHAUVET
®
website: www.chauvetpro.com.
Always connect this product to a protected circuit with an appropriate electrical
ground to avoid the risk of electrocution or fire.
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0% to 100% switch.
AC Plug
The Legend™ 230SR Beam comes with a bare ended power input cord. The product
side of this power cord enters the product through a strain reliever (rubber boot) and
it
cannot be disconnected from the product
. Use the table below to wire the plug to the
power cord.
Connection
Wire (U.S.)
Wire (Europe)
Screw Color
AC Live
Black
Brown
Yellow or Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
Make sure to disconnect the product’s power cord before replacing a blown fuse.
Always replace with a fuse of the same type and rating.
Fuse Replacement
1. Disconnect this product from the power outlet.
2. Using a Phillips #2-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse and replace with a good fuse of the same type and rating
(T 5 A, 250 V).
4. Screw the fuse holder cap back in place and reconnect power.
DMX Linking
You can link the Legend™ 230SR Beam to a DMX controller using a standard DMX
serial connection. If using other DMX compatible products with the
Legend™ 230SR
Beam, you can control each individually with a single DMX controller.
DMX Modes
The Legend™ 230SR Beam uses the standard DMX data connection for the 15 and 18
channel DMX modes.
•Refer to the Introduction for a brief description of these modes.
•Refer to Operation to learn how to configure the Legend™ 230SR Beam to work in
these modes.
•The DMX Values section will provide detailed information regarding the DMX modes.
If you are not familiar with or need more information about DMX standards,
Master/Slave connectivity, or the DMX cables needed to link this product to a DMX
controller, download the DMX Primer from the CHAUVET® website:
www.chauvetpro.com.

Setup
Legend™ 230SR Beam User Manual Rev. 1 7
Gobo Wheel
The Legend™ 230SR Beam includes one gobo wheel with 17 fixed gobos. The diagram
shows the gobo on the wheel, as per the DMX Values tables.
Color Wheel
The Legend™ 230SR Beam includes one gobo wheel with 14 fixed colors, as indicated
below. The diagram shows the color on the wheel, as per the DMX Values tables.

Setup
8 Legend™ 230SR Beam User Manual Rev. 1
Lamp Replacement
The Legend™ 230SR Beam is equipped with a Osram Sirius 230W lamp. Follow the
procedure below to safely change the lamp.
Disconnect the product from the AC power before opening.
Do not turn product on without a lamp!
Procedure
1. Turn the product off and disconnect it from the power outlet. Wait at least 15 minutes
for the lamp to cool down.
2. Remove both head covers by removing 8 Phillips head ¼-turn screws.
3. Orientate the bottom of the moving head so that the fan is up.

Setup
Legend™ 230SR Beam User Manual Rev. 1 9
4. Remove the 2 Phillips head screws on the sides of the fan assembly.
5. Roll the fan assembly to the right to expose the lamp.
6. Using the lamp base, push the lamp down against the spring clips located on the
bottom, then roll the lamp out the top.
7. Remove the 2 wires connected to the lamp by spade connectors.
8. Reverse the steps above to install the new lamp.
Increasing the Lamp’s
Life
•ALWAYS turn the lamp off by using the DMX controller or the product’s control
panel. Then wait at least 5 minutes before switching off the product. This will
keep the fans running to extract any remaining heat from the product’s head.
•DO NOT power cycle the product unless it is necessary.
•DO NOT touch the lamp without wearing gloves to avoid leaving grease on the
bulb or on the contacts that could reduce the lamp’s life.
•ALWAYS change the lamp when it has reached its recommended lifespan to
avoid the risk of lamp explosion.

Setup
10 Legend™ 230SR Beam User Manual Rev. 1
Mounting
Before mounting this product, read and follow the Safety Notes.
Orientation
Always mount this product in a safe position and make sure there is adequate room for
ventilation, configuration, and maintenance.
Rigging
CHAUVET® recommends the following general guidelines when mounting this product:.
•When selecting an installation location, consider easy access to this product for
operation, programming adjustments, and routine maintenance.
•Make sure to mount this product away from any flammable material as indicated in
the Safety Notes.
•Never mount in places where rain, high humidity, extreme temperature changes, or
restricted ventilation may affect the product.
•If hanging this product, make sure that the mounting location can support the
product’s weight. Refer to the Technical Specifications chart for the weight-bearing
requirements of this product.
•When hanging this product, always secure to a fastening device using a safety
chain/cable (not included).
Product Mounting Diagram
The Legend™ 230SR Beam comes with a preinstalled mounting bracket to which you
will be able to attach the 2 included omega clamps. U
se two mounting points per
product. In addition, use a safety cable (not included) to link the product to the structure.
Overhead Mounting
Floor Mounting

Operation
Legend™ 230SR Beam User Manual Rev. 1 11
4. Operation
Control Panel
Description
Button Function
<MENU>
Exits from the current menu or function
<ENTER>
Enables the currently displayed menu or sets the currently
selected value in to the current function
<UP>
Navigates upward through the menu list and increases the
numeric value when in a function
<DOWN>
Navigates downward through the menu list and decreases the
numeric value when in a function
LCD Display
The Legend™ 230SR Beam features a backlit liquid crystal display (LCD) that provides
information regarding the product
’s settings and status. In addition, the LCD is
reversible. This allows reading it normally whether the product
is on the floor or hanging
from a truss.
Upon power up, the LCD will show the Legend logo and the product
identification After
completing the po
wer up tests, the LCD will show the DMX address, the DMX mode, and
the temperature, along with the warning sign if the tests have detected an error.
Press <ENTER> to read the corresponding error message (see Error Messages in
the Technical Information section).
Press <ENTER> while looking at the error messages to clear them.
Control Options
You can set the Legend™ 230SR Beam start address in the 001~512 DMX range. This
allows for the control of up to 28 products in the 18-channel Mode 2. The
Legend™
230SR Beam works with any compatible DMX controller using standard DMX cables.
Programming
Carry out all the programming procedures indicated below from the control panel. Refer
to the Menu Map page to learn how the menu options relate to each other
Navigation Buttons
•To enter programming mode, press <MENU> until you see the Main Menu.
•To highlight a menu option or to change a setting, press <UP> or <DOWN>.
•To change menu levels as shown in the Menu Map,press <ENTER> or <MENU>.
This is equivalent to moving right and left of the Menu Map, respectively.
•To accept the current or new value, press <ENTER>.
•To return to the previous menu without making changes, press <MENU>.
•To exit programming mode, press <MENU> until you see the Main Menu or do not
press any button for 30 seconds.
DMX Functions
From the Main Menu, highlight DMX Functions and press <ENTER> (a new menu with
the DMX functions will open).
DMX Address
1. Highlight DMX Address.
2. Press <MENU> to exit or continue below.
3. To change the current address, press <ENTER>.
a. Change the starting address (001~512).
b. Accept the new value.
DMX Mode
1. Highlight DMX Channel Mode.
2. Press <MENU> to exit or continue below.
3. To change the current mode, press <ENTER>.
a. Select a DMX mode (Mode 1/Mode 2).
b. Accept the selected option.

Operation
12 Legend™ 230SR Beam User Manual Rev. 1
View DMX Values
1. Highlight View DMX Value.
2. Press <MENU> to exit or continue below.
3. Press <ENTER>.
a. Scroll along the list to see the values of all the current attributes.
b. Return to the previous menu.
The list will show either 15 or 18 attributes, depending on the current DMX mode.
Product Settings
From the Main Menu, highlight Fixture Settings and press <ENTER>.
Reverse Pan Direction
1. Highlight Pan Inverse.
2. To reverse the pan direction, press <ENTER>.
a. Select YES to reverse the pan direction or NO to use the normal pan
direction.
b. Accept the selected option.
Reverse Tilt Direction
1. Highlight Tilt Inverse.
2. To reverse the tilt direction, press <ENTER> (a pop up window will open).
a. Select YES to reverse the tilt direction or NO to use the normal tilt direction.
b. Accept the selected option.
Head Motion Black Out
1. Highlight Bl.o P/T Moving.
2. To black out the output when the head moves, press <ENTER>.
a. Select YES to black out the output when the head tilts or pans, or NO to keep
the output on while the head moves.
b. Accept the selected option.
Color Change Blackout
1. Highlight Bl.o Color Change.
2. To black out the output when the color wheel changes, press <ENTER>.
a. Select YES to black out the output during a color change or NO to keep the
output on to see the color changing.
b. Accept the selected option.
Gobo Change Blackout
1. Highlight Bl.o Gobo Change.
2. To black out the output when the gobo wheel changes, press <ENTER>.
a. Select YES to black out the output during a gobo change or NO to keep the
output on to see the gobo changing.
b. Accept the selected option.
Lamp Settings
From the Main Menu, highlight Fixture Settings and press <ENTER>.
The lamp will not ignite if the ambient temperature is 104º F (40º C) or higher.
Lamp On / Off
1. Highlight On/Off.
2. To turn the lamp on or off, press <ENTER>.
a. Select ON to turn the lamp on or OFF to turn the lamp off.
b. Accept the selected option.
Lamp Status During Power
On
1. Highlight State/Power On.
2. To change the lamp status during power on, press <ENTER>.
a. Select ON to turn on the product and the lamp simultaneously or OFF to turn
on the product without turning on the lamp.
b. Accept the selected option.

Operation
Legend™ 230SR Beam User Manual Rev. 1 13
Remote Turn Off
1. Highlight Off Via DMX.
2. To enable/disable remote turn off, press <ENTER>.
a. Select YES to enable product turn off from either a DMX controller or its
power switch, or NO to turn the product off only from its power switch.
b. Accept the selected option.
Lamp On if DMX Present
1. Highlight On if DMX On.
2. To turn the lamp on when DMX is present, press <ENTER>.
a. Select YES to turn the lamp on if DMX signal is present, or NO to turn the
lamp on only from the control panel.
b. Accept the selected option.
Lamp Off if DMX Absent
1. Highlight Off if DMX Off.
2. To turn the lamp off when DMX is absent, press <ENTER>.
a. Select YES to turn the lamp off if DMX signal is absent, or NO
to turn the lamp
off only from the control panel.
b. Accept the selected option.
Lamp Strike Delay
1. Highlight Ignition Delay.
2. To set the lamp strike delay, press <ENTER>.
a. Select the delay before the lamp strikes after power up in seconds (000~255).
b. Accept the new value.
Fixture Shut Off Delay
1. Highlight Low Power Delay.
2. To set the lamp shut off delay, press <ENTER>.
a. Select the delay before the product powers off after lamp off in seconds
(000~255).
b. Accept the new value.
Display Settings
From the Main Menu, highlight Display Settings and press <ENTER>.
Overturn Display
1. Highlight Display Inverse.
2. To overturn the display, press <ENTER>.
a. Select YES to turn the LCD around or NO to keep the normal LCD view.
b. Accept the selected option.
LCD Backlight Off
1. Highlight Backlight Auto Off.
2. To configure the LCD backlight, press <ENTER>.
a. Select YES to automatically turn the LCD backlight off or NO to keep the LCD
backlight always on.
b. Accept the selected option.
Backlight Brightness
1. Highlight Backlight Intensity.
2. To set the backlight brightness, press <ENTER>.
a. Select the backlight brightness (1~10), being “1” the darkest and “10” the
brightest settings.
b. Accept the new value.
Temperature Unit
1. Highlight Temperature Unit.
2. To select the temperature unit, press <ENTER>.
a. Select ºC to show the temperature in the Celsius scale or ºF to show the
temperature in the Fahrenheit scale.
b. Accept the selected option.

Operation
14 Legend™ 230SR Beam User Manual Rev. 1
Fixture Tests
From the Main Menu, highlight Display Settings and press <ENTER>.
Automatic Fixture Test
1. Highlight Auto Test.
2. To start the built-in test sequence, press <ENTER>.
a. The product will start the test sequence.
b. You can stop the test by pressing <MENU>.
c. Return to the previous menu.
The automatic fixture test runs only once after activation.
Manual Fixture Test
1. Highlight Manual Test and press <ENTER>.
2. Highlight the desired attribute.
3. To change the value of the selected attribute, press <ENTER>.
a. Set the attribute value (000~255).
b. Accept the new value.
4. Repeat steps 2 and 3 for the other attributes.
5. When done with the test, exit to the previous menu (the values of all tested channels
will go back to zero).
Fixture Information
From the Main Menu, highlight Fixture Information and press <ENTER.
Fixture Operation Timer
1. Highlight Fixture Use Time (the accumulated product’s operation time will show).
You cannot modify or reset the fixture operation timer.
Lamp Operation Timer
1. Highlight Lamp On Time (the accumulated lamp’s operation time will show).
2. To reset the lamp operation timer, press <ENTER>.
a. Select Reset Time to reset the timer or Exit to exit without resetting.
b. Accept the selected option.
Firmware Version
1. Highlight Firmware Version.
2. To see the firmware versions installed, press <ENTER>.
a. The display will show the current firmware version for each of the four CPU
boards (A through D) in the product.
b. Return to the previous menu.
Reset Functions
From the Main Menu, highlight Reset and press <ENTER>.
You can leave this sub-menu at any time by pressing <MENU>.
Pan/Tilt Reset
1. Highlight Pan/Tilt and press <ENTER>.
a. Select YES to reset the pan and tilt movements to their home positions.
b. Accept the selected option.
Shutter/Prism Reset
1. Highlight Shutter/Prism and press <ENTER>.
a. Select YES to reset the shutter and dimmer to their home positions.
b. Accept the selected option.

Operation
Legend™ 230SR Beam User Manual Rev. 1 15
Color Reset
1. Highlight Color and press <ENTER>.
a. Select YES to reset the color wheel and the CMY filters to their home
positions.
b. Accept the selected option.
Gobo Reset
1. Highlight Gobo and press <ENTER>.
a. Select YES to reset the gobo wheel to its home position.
b. Accept the selected option.
Zoom/Frost/Focus Reset
1. Highlight Zoom/Frost/Focus and press <ENTER>.
a. Select YES to reset the prism and the frost to their home positions.
b. Accept the selected option.
Reset All
1. Highlight All and press <ENTER>.
a. Select YES to reset all moving optical parts and the moving head to their
home positions.
b. Accept the selected option.
Special Functions
From the Main Menu, highlight Special Functions and press <ENTER>.
Fixture Maintenance Timers
1. Highlight Fixture Maintenance and press <ENTER> (the current maintenance
interval and remaining time will show).
2. To change the maintenance interval timer, highlight Interval and press <ENTER>.
a. Select the new interval (in hours).
b. Accept the new value.
3. To reset the remaining time counter, highlight Remain Time and press <ENTER>.
a. Select Reset Time to reset the timer or Exit to exit without resetting it.
b. Accept the selected option.
It is a good idea to use the Fixture Maintenance Time as a reminder to change the
lamp.
Fixture Defaulting
1. Highlight Factory Setting and press <ENTER>.
a. Select YES to default the product to factory settings, or NO to exit without
resetting.
b. Accept the selected option and wait for the product to reset.
c. Return to the previous menu.
Offset Mode
The Offset Mode provides fine adjustments for the home position of all the moving parts
in the optical path as well as the pan and tilt movements. This way,
when in their home
position, the moving parts do not show any border or reduce the light output.
Entering Offset Mode
1. Press <MENU> to enter the regular Menu Mode.
2. Press <ENTER> for more than three seconds to enter the Offset Mode (the Offset
Mode menu will show).
Pan
1. Select Pan and press <ENTER>.
a. Select the new value (-128~127).
b. Accept the new value.
Tilt
1. Select Tilt and press <ENTER>.
a. Select the new value (-128~127).
b. Accept the new value.

Operation
16 Legend™ 230SR Beam User Manual Rev. 1
Shutter
1. Select Shutter and press <ENTER>.
a. Select the new value (000~255).
b. Accept the new value.
Color
1. Select Color and press <ENTER>.
a. Select the new value (-128~127).
b. Accept the new value.
Gobo
1. Select Gobo and press <ENTER>.
a. Select the new value (-128~127).
b. Accept the new value.
Prism
1. Select Prism and press <ENTER>.
a. Select the new value (000~255) and press <ENTER>.
b. Return to the Offset Mode menu.
R-Prism
1. Select R-Prism and press <ENTER>.
a. Select the new value (-128~127).
b. Accept the new value.
Zoom
1. Select Zoom and press <ENTER>.
a. Select the new value (000~255).
b. Accept the new value.
Focus
1. Select Focus and press <ENTER>.
a. Select the new value (000~255).
b. Accept the new value.
Frost
1. Select Frost and press <ENTER>.
a. Select the new value (000~255).
b. Accept the new value.