Chauvet CORE User manual

User Manual

Page 2 of 23 CORE™ 3x3 User Manual Rev. 1
TABLE OF CONTENTS
1. Before You Begin...........................................................................................................3
What Is Included .........................................................................................................................3
Unpacking Instructions................................................................................................................3
Claims.................................................................................................................................................3
Text Conventions ........................................................................................................................3
Symbols......................................................................................................................................3
Disclaimer...................................................................................................................................3
Product at a Glance.....................................................................................................................4
Safety Notes ...............................................................................................................................4
2. Introduction....................................................................................................................5
Overview.....................................................................................................................................5
Dimensions.................................................................................................................................6
3. Setup...............................................................................................................................7
AC Power....................................................................................................................................7
Fuse Replacement...............................................................................................................................7
Power Linking......................................................................................................................................8
Mounting.....................................................................................................................................9
Orientation...........................................................................................................................................9
Rigging................................................................................................................................................9
Coffin Locks.......................................................................................................................................10
4. Operation......................................................................................................................11
Control Panel Operation............................................................................................................11
Menu Map.................................................................................................................................11
Configuration (DMX)..................................................................................................................12
Starting Address ................................................................................................................................12
CORE™ 3x3 Sections for DMX Control.....................................................................................12
DMX Channel Modes, Assignments, and Values.......................................................................13
31-Channel........................................................................................................................................13
DMX Channel Modes, Assignments, and Values (cont.) ............................................................14
27-Channel........................................................................................................................................14
DMX Channel Modes, Assignments, and Values (cont.) ............................................................15
9-Channel..........................................................................................................................................15
DMX Channel Modes, Assignments, and Values (cont.) ............................................................16
5-Channel..........................................................................................................................................16
3-Channel..........................................................................................................................................16
Configuration (Standalone)........................................................................................................17
Sound-Active Mode............................................................................................................................17
Sound Sensitivity ...............................................................................................................................17
Auto Program.....................................................................................................................................17
Program Speed..................................................................................................................................17
Static Colors......................................................................................................................................18
Custom Color Mixing..........................................................................................................................18
Dimmer..............................................................................................................................................18
Fan Settings ......................................................................................................................................18
Master/Slave Mode............................................................................................................................19
Two-by-Two (2 x 2) Master/Slave Mode..............................................................................................20
5. Technical Information..................................................................................................21
Product Maintenance ................................................................................................................21
6. Technical Specifications..............................................................................................22
Returns.....................................................................................................................................23
Contact Us................................................................................................................................23

CORE™ 3x3 User Manual Rev. 1 Page 3 of 23
1.BEFORE YOU BEGIN
What Is
Included
•CORE™ 3x3
•5 mm Allen Key
•Hanging Bracket with Mounting
Hardware
•Power Cord
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately
and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and
included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as
missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Text
Conventions
Convention Meaning
1–512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this User Manual
are subject to change
without notice. CHAUVET® assumes no responsibility or liabil
ity for any errors or
omissions, and reserves the right to revise or recreate this manual at any time.
Download the latest version from www.chauvetlighting.com.
© Copyright 2013 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author
Date
Editor
Date
A. Leon 05/16/13 T. Yeago 05/16/13

Page 4 of 23 CORE™ 3x3 User Manual Rev. 1
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Activated
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
These notes include important information about the mounting, usage, and maintenance
of this product; read before using the product.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Contact the nearest authorized technical assistance center.
•This product is not intended for permanent installation.
•Keep this User Manual for future use. If you sell the product to another user, be
sure to give this document to the next owner.

CORE™ 3x3 User Manual Rev. 1 Page 5 of 23
2.INTRODUCTION
Overview
Microphone
Display and
Control Buttons DMX Out DMX In Fuse Holder
Back Panel View
Power In Power Out

Page 6 of 23 CORE™ 3x3 User Manual Rev. 1
Dimensions
13.6 in
344 mm
13.6 in
344 mm
6.2 in
156 mm

CORE™ 3x3 User Manual Rev. 1 Page 7 of 23
3.SETUP
AC Power
The CORE™ 3x3 has an auto-
ranging power supply and it can work with an input
voltage range of 100~240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit
(circuit breaker or fuse). Make
sure the product has
an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to
a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0–100% switch.
Fuse
Replacement
Disconnect the product from power before replacing the fuse.
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
A spare fuse is not included; however, the safety cap has room for a spare.
Always replace a blown fuse with another of the same type and rating.
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap

Page 8 of 23 CORE™ 3x3 User Manual Rev. 1
Power Linking
The product provides power linking via the Edison/IEC outlet located in the back of the
unit.
Power Linking
Diagram
You can power link up to 3 CORE™ 3x3 units on 120 VAC or up to 7 CORE™ 3x3
units on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product
in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
1st Product
2nd Product
3rd Product
Additional Products

CORE™ 3x3 User Manual Rev. 1 Page 9 of 23
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The CORE™ 3x3 may be mounted in any position
; however, make sure adequate
ventilation is provided around the product.
Rigging
•Before deciding on a location, always make sure there is easy access to the product
for maintenance and programming.
•Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight (see the Technical Specifications).
•When mounting the product overhead, always use a safety cable.
Mount the
product securely to a rigging point, such as an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The bracket has a 13-mm hole, which is
appropriate for
this purpose.
•When power linking multiple products, you must always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
•The bracket adjustment knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
•When mounting the product on the floor, make sure that the product and cables are
away from people and vehicles.
Mounting Diagram
Hanging/Mounting
Bracket
Mounting Clamp
Bracket
Adjustment
Knobs
Safety Cable

Page 10 of 23 CORE™ 3x3 User Manual Rev. 1
Coffin Locks
The CORE™ 3x3 may be attached to another CORE™ 3x3 by using their coffin locks.
The coffin locks are for product alignment only and are not weight bearing. DO NOT
hang product using only the coffin locks.
1. Place one CORE™ 3x3 next to the other, making sure to align the coffin lock’s male
connector opening to the other product’s female connector opening.
2. Use the 5 mm Allen key to operate the locking mechanism. Once locked, the coffin
lock hooks hold the CORE™ 3x3 units together.
Note: To unlock the coffin locks, using the Allen key again, simply turn the key in the
opposite direction from how it was locked.
When attaching CORE™
3x3 products together using their coffin locks, be sure
each unit is independently mounted.
Coffin Lock Keyways

CORE™ 3x3 User Manual Rev. 1 Page 11 of 23
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display.
Button Function
<MENU> Selects an operation mode or to backs out of the current menu option
<UP> Scrolls up the list of options or selects a higher value
<DOWN>
Scrolls down the list of options or selects a lower value
<ENTER> Activates a menu option or a selected value
Menu Map
Main Level
Programming Levels
Description
DMX
Personalities
and Starting
Address
3-CH
d 1–d512 Selects DMX personality and
starting address
5-CH
9-CH
27CH
31CH
Static Colors C--
r
Red
g
Green
b Blue
gb Cyan
r b Magenta
rg
Yellow
rgb White
Auto Program P-- P 1–P 6 Auto programs
Program Speed S-- S 1–S100 Selects auto program speed (slow to fast)
Sound-Active
Mode Snd Sound-Active mode
Sound
Sensitivity
SEnS u 0–u100 Sound sensitivity control
Custom Color
Mixing U--
r 0–r255
Red (0–100%)
g 0–g255
Green (0–100%)
b 0–b255 Blue (0–100%)
Dimmer dIM
OFF Dimmer speed off
dIM1 Dimmer, fast speed
dIM2
Dimmer, medium speed
dIM3 Dimmer, slow speed
Fan Settings FAN
AUTO
Fan automatically turns on
HIGH
Fan always on
Master Modes SEnd SEd1 Mode 1 (see Master/Slave Mode)
SEd4 Mode 4 (see Two-by-Two Master/Slave Mode)
Slave Modes SLA SLA1–SLA4 Slave modes 1–4

Page 12 of 23 CORE™ 3x3 User Manual Rev. 1
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you
choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The CORE™ 3x3 uses up to 31 DMX channels in its 31-channel
DMX mode, which
defines the highest configurable address to 482.
If unfamiliar with DMX or DIP switches,
download the DMX Primer from
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU>repeatedly until 3-CH, 5-CH, 9-CH, 27CH, or 31CH shows on the
display.
2. Press <ENTER> to activate the selected DMX personality and d 1–d512 shows on
the display.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.
CORE™ 3x3 Sections for DMX Control
Section 1 Section 2 Section 3
Section 4
Section 9
Section 8
Section 7
Section 6
Section 5

CORE™ 3x3 User Manual Rev. 1 Page 13 of 23
DMX Channel Modes, Assignments, and Values
31-Channel
Channel Function Value Setting
1
Red
000 ó255
0–100%
Section 1
2
Green
000 ó255
0–100%
3
Blue
000 ó255
0–100%
4
Red
000
ó
255
0–100%
Section 2
5
Green
000 ó255
0–100%
6
Blue
000 ó255
0–100%
7
Red
000 ó255
0–100%
Section 3
8
Green
000 ó255
0–100%
9
Blue
000 ó255
0–100%
10
Red
000 ó255
0–100%
Section 4
11
Green
000 ó255
0–100%
12
Blue
000 ó255
0–100%
13
Red
000
ó
255
0–100%
Section 5
14
Green
000 ó255
0–100%
15
Blue
000 ó255
0–100%
16
Red
000 ó255
0–100%
Section 6
17
Green
000 ó255
0–100%
18
Blue
000 ó255
0–100%
19
Red
000 ó255
0–100%
Section 7
20
Green
000 ó255
0–100%
21
Blue
000 ó255
0–100%
22
Red
000 ó255
0–100%
Section 8
23
Green
000 ó255
0–100%
24
Blue
000 ó255
0–100%
25
Red
000 ó255
0–100%
Section 9
26
Green
000 ó255
0–100%
27
Blue
000 ó255
0–100%
28 Auto Programs
000 ó010
No function
011 ó040
Chase 1
041 ó080
Chase 2
081 ó120
Chase 3
121 ó160
Chase 4
161 ó200
Chase 5
201
ó
240
Chase 6 (run Chases 1–4)
241 ó255
Sound-Active mode
29
Speed
000 ó255
Auto programs speed (slow to fast)
30
Dimmer
000 ó255
0–100%
31 Shutter
000 ó010
No function
011 ó255
Strobe (slow to fast)

Page 14 of 23 CORE™ 3x3 User Manual Rev. 1
DMX Channel Modes, Assignments, and Values (cont.)
27-Channel
Channel Function Value Setting
1
Red
000 ó255
0–100%
Section 1
2
Green
000 ó255
0–100%
3
Blue
000 ó255
0–100%
4
Red
000
ó
255
0–100%
Section 2
5
Green
000 ó255
0–100%
6
Blue
000 ó255
0–100%
7
Red
000 ó255
0–100%
Section 3
8
Green
000 ó255
0–100%
9
Blue
000 ó255
0–100%
10
Red
000 ó255
0–100%
Section 4
11
Green
000 ó255
0–100%
12
Blue
000 ó255
0–100%
13
Red
000
ó
255
0–100%
Section 5
14
Green
000 ó255
0–100%
15
Blue
000 ó255
0–100%
16
Red
000 ó255
0–100%
Section 6
17
Green
000 ó255
0–100%
18
Blue
000 ó255
0–100%
19
Red
000 ó255
0–100%
Section 7
20
Green
000 ó255
0–100%
21
Blue
000 ó255
0–100%
22
Red
000 ó255
0–100%
Section 8
23
Green
000 ó255
0–100%
24
Blue
000 ó255
0–100%
25
Red
000 ó255
0–100%
Section 9
26
Green
000 ó255
0–100%
27
Blue
000 ó255
0–100%

CORE™ 3x3 User Manual Rev. 1 Page 15 of 23
DMX Channel Modes, Assignments, and Values (cont.)
9-Channel
Channel Function Value Setting
1
Dimmer
000 ó255
0–100%
2
Red
000 ó255
0–100%
3
Green
000 ó255
0–100%
4
Blue
000 ó255
0–100%
5 Shutter
000 ó010
No function
011 ó255
Strobe (slow to fast)
6 Custom Color and
Color Temperature
000 ó010
No function
011 ó030
Red 100% + Green 0–100%
031 ó050
Red 100%–0 + Green 100%
051 ó070
Green 100% + Blue 0–100%
071 ó090
Green 100%–0 + Blue 100%
091 ó110
Red 0–100% + Blue 100%
111 ó130
Red 100% + Blue 100%–0
131 ó150
Red 100% + Green 0–100% + Blue 0–100%
151 ó170
Red 100%–0 + Green 100%–0 + Blue 100%
171 ó200
Red 100% + Green 100% + Blue 100%
201 ó205
Color temperature 1
206 ó210
Color temperature 2
211 ó215
Color temperature 3
216 ó220
Color temperature 4
221 ó225
Color temperature 5
226 ó230
Color temperature 6
231 ó235
Color temperature 7
236
ó
240
Color temperature 8
241 ó245
Color temperature 9
246 ó250
Color temperature 10
251 ó255
Color temperature 11
7 Auto Programs
000 ó010
No function
011 ó040
Chase 1
041 ó080
Chase 2
081 ó120
Chase 3
121 ó160
Chase 4
161 ó200
Chase 5
201 ó240
Chase 6 (run Chases 1–4)
241 ó255
Sound-Active mode
8
Speed
000 ó255
Auto programs speed (slow to fast)
9 Dimmer Mode
000 ó051
Dimmer mode manually set in Menu Options
052 ó101
Dimmer mode off
102 ó152
Dimmer mode 1 (fast speed)
153 ó203
Dimmer mode 2 (middle speed)
204 ó255
Dimmer mode 3 (slow speed)

Page 16 of 23 CORE™ 3x3 User Manual Rev. 1
DMX Channel Modes, Assignments, and Values (cont.)
5-Channel
Channel Function Value Setting
1
Dimmer
000 ó255
0–100%
2
Red
000 ó255
0–100%
3
Green
000 ó255
0–100%
4
Blue
000 ó255
0–100%
5 Shutter
000 ó010
No function
011 ó255
Strobe (slow to fast)
3-Channel
Channel Function Value Setting
1
Red
000 ó255
0–100%
2
Green
000 ó255
0–100%
3
Blue
000 ó255
0–100%

CORE™ 3x3 User Manual Rev. 1 Page 17 of 23
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to power.
2. Turn the product on.
Never connect a product that is operating in any standalone mode (either Static,
Automatic, or Sound) to a DMX string connected to a DMX controller. Products in
standalone mode may transmit DMX
signals that could interfere with the DMX
signals from the controller.
Sound-
Active
Mode
To enable the Sound-Active mode, do the following:
1. Press <MENU>repeatedly until Snd shows on the display.
2. Press <ENTER>.
Sound Sensitivity
To set the sound sensitivity, follow the instructions below:
1. Press <MENU> repeatedly until SEnS shows on the display.
2. Use <UP> or <DOWN>to select the desired sound sensitivity (u 0–u100).
3. Press <ENTER>.
The product will only respond to low frequencies of music (bass and drums).
Auto Program
To select an auto program, do the following:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER> and P 1–P 6 shows on the display.
3. Use <UP> or <DOWN> to select the desired auto program.
4. Press <ENTER>.
Program Speed
To set the auto program speed, follow the instructions below:
1. Press <MENU> repeatedly until S-- shows on the display.
2. Use <UP> or <DOWN> to select the desired auto program speed
(S 1–S100, slow to fast).
3. Press <ENTER>.

Page 18 of 23 CORE™ 3x3 User Manual Rev. 1
Static Colors
To select a static color, do the following:
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the desired preset color:
•r(red)
•g(green)
•b(blue)
•gb (cyan)
•r b (magenta)
•rg (yellow)
•rgb (white)
4. Press <ENTER>.
Custom Color
Mixing
To custom mix a color, follow the instructions below:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER> and one of the following colors shows on the display: rXXX (red),
gXXX (green), or bXXX (blue).
3. Press <ENTER> repeatedly to select the desired color.
4. Use <UP> or <DOWN> to select the desired color value (0–100).
NOTE: Selecting 0will turn the color off.
5. Press <ENTER> to select color value and continue to the next color.
6. Repeat steps 3 to 5 until you create your desired color.
Dimmer
To select a dimmer mode, do the following:
1. Press <MENU> repeatedly until dIM shows on the display.
2. Press <ENTER> and one of the following shows on the display:
•OFF (dimmer speed off)
•dIM1 (dimmer, fast speed)
•dIM2 (dimmer, medium speed)
•dIM3 (dimmer, slow speed)
3. Use <UP> or <DOWN> to select the desired dimmer mode.
4. Press <ENTER>.
Fan Settings
To select a fan setting, follow the instructions below:
1. Press <MENU> repeatedly until FAN shows on the display.
2. Press <ENTER> and either AUTO (fan automatically turns on) or HIGH
(fan always on) shows on the display.
3. Use <UP> or <DOWN> to select the desired fan setting.
4. Press <ENTER>.

CORE™ 3x3 User Manual Rev. 1 Page 19 of 23
Master/Slave
Mode
The Master/Slave mode allows a single CORE™ 3x3
unit (the “master”) to control the
actions of one or more CORE™ 3x3
units (the “slaves”) without the need of a DMX
controller. The master unit will be set to operate in Master mode 1 (and in either an Auto
program or Sound-Active mode), while the slave units will be set to operate in Slave
mode 1
. Once set and connected, the slave units will operate in unison with the master
unit, each slave duplicating the master exactly.
Configure the units as indicated below.
Slave units:
1. Press <MENU> on the slave units until SLA shows on the display.
2. Press <ENTER> and SLA1–SLA4 shows on the display.
3. Use <UP> or <DOWN> to select SLA1(Slave mode 1).
4. Press <ENTER>.
5. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
Master unit:
1. Press <MENU> on the master unit until SEnd shows on the display.
2. Press <ENTER> and either SEd1 or SEd4shows on the display.
3. Use <UP> or <DOWN> to select SEd1(Master mode 1).
4. Press <ENTER>.
5. Set the master unit to operate in either Auto program or Sound-Active mode.
6. Make the master unit the first unit in the DMX daisy chain.
•Configure
all the slave units before connecting the master unit to the DMX
daisy chain.
•
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller
may interfere with the signals from the
master unit.
•Do not connect more than 31 slave units to the master unit.

Page 20 of 23 CORE™ 3x3 User Manual Rev. 1
Two-by-Two
(2 x 2)
Master/Slave
Mode
The Two-by-Two (2 x 2)
Master/Slave mode allows a single CORE™ 3x3 unit (the
“master”) to control the actions of 3 other CORE™ 3x3 units (the “slaves”) as
if they
were one unit, when positioned 2 units across by 2 units down. The master
unit will be
set to operate in Master mode 4 (and in either an Auto program or Sound-Active mode),
while the slave units will be set to operate in Slave modes 2 through 4
. Once set and
connected, the four units will operate as one.
Configure the units as indicated below.
Slave units:
1. Press <MENU> on the slave units until SLA shows on the display.
2. Press <ENTER> and SLA1–SLA4 shows on the display.
3. Use <UP> or <DOWN> to select SLA2 for the slave next to the master, SLA3 for
the slave diagonal to the master, and SLA4 for the slave underneath the master.
4. Press <ENTER> on the slave units.
5. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
Master unit:
1. Press <MENU> on the master unit until SEnd shows on the display.
2. Press <ENTER> and either SEd1 or SEd4shows on the display.
3. Use <UP> or <DOWN> to select SEd4 (Master mode 4).
4. Press <ENTER>.
5. Set the master unit to operate in either Auto program or Sound-Active mode.
6. Make the master unit the first unit in the DMX daisy chain.
Placement of Units
for Two-by-Two
Master/Slave Mode
The SEd4 setting in the master unit is for the two-by-two grid layout only. With
this two-by-two configuration, be sure to place the slave units in the positions
shown to ensure all 4 units generate a properly coordinated show.
Additional
Two-by-Two
Configurations
Master Unit
SEd4 Mode
Slave Unit
SLA4 Mode
Slave Unit
SLA2 Mode
Slave Unit
SLA3 Mode
Back Panel View
First 2x2 Setup
(as shown above)
Additional 2x2 Setups
Slave Unit
SLA1 Mode
Slave Unit
SLA2 Mode
Slave Unit
SLA3 Mode
Slave Unit
SLA4 Mode