Chauvet SlimPAR Tri IRC 7 IRC User manual

User Manual

Page 2 of 25 SlimPAR™ Tri IRC series User Manual (Rev. 04)
TABLE OF CONTENTS
1. Before You Begin.................................................................................4
What Is Included ...............................................................................................4
Unpacking Instructions......................................................................................4
Claims........................................................................................................................ 4
Text Conventions..............................................................................................4
Icons..................................................................................................................4
Document Information.......................................................................................4
Product at a Glance ..........................................................................................5
Safety Notes......................................................................................................5
2. Introduction..........................................................................................6
Product Overview (SlimPAR™ Tri 12 IRC).......................................................6
Product Overview (SlimPAR™ Tri 7 IRC).........................................................7
Product Dimensions (SlimPAR™ Tri 12 IRC)...................................................8
Product Dimensions (SlimPAR™ Tri 7 IRC).....................................................9
3. Setup...................................................................................................10
AC Power........................................................................................................10
Fuse Replacement................................................................................................... 10
Power Linking........................................................................................................... 11
Mounting .........................................................................................................12
Orientation ............................................................................................................... 12
Rigging..................................................................................................................... 12
4. Operation............................................................................................13
Control Panel Operation..................................................................................13
Menu Map.......................................................................................................13
Configuration (DMX) .......................................................................................14
Starting Address....................................................................................................... 14
Configuration (Standalone).............................................................................14
Automatic Mode....................................................................................................... 14
Static Color Mode..................................................................................................... 14
Custom Static Color Mode ....................................................................................... 14
Master/Slave Mode.................................................................................................. 15
Infrared Control........................................................................................................ 15
IRC (Infrared Remote Control) Operation ................................................................ 16
DMX Channel Assignments and Values.........................................................17
7-CH......................................................................................................................... 17
3-CH......................................................................................................................... 17
5. Technical Information........................................................................18
Product Maintenance......................................................................................18
General Troubleshooting ................................................................................19
Contact Procedure..........................................................................................20
CHAUVET® Contact Information....................................................................20
Returning Products to CHAUVET® ................................................................20
DMX Primer ............................................................................................21
Introduction .....................................................................................................21
The Physical Medium............................................................................................... 21
The Signals.............................................................................................................. 21
DMX Universes........................................................................................................ 21
The Functions .......................................................................................................... 21
DMX Configuration..........................................................................................22
Personalities ............................................................................................................ 22
Starting Address....................................................................................................... 22
Assigning Addresses................................................................................................ 22

SlimPAR™ Tri IRC series User Manual (Rev. 04) Page 3 of 25
DMX Connectivity............................................................................................22
Fixture Location........................................................................................................ 22
Number of Fixtures................................................................................................... 23
DMX Data Cabling ................................................................................................... 23
Making Your Own DMX Cable ................................................................................. 23
DMX Cable Characteristics...................................................................................... 23
DMX Cable Connectors ........................................................................................... 23
3-Pin to 5-Pin Conversion Chart............................................................................... 24
DMX Connection...................................................................................................... 24
6. Technical Specifications...................................................................25

Page 4 of 25 SlimPAR™ Tri IRC series User Manual (Rev. 04)
1. B EFORE Y OU B EGIN
What Is
Included
1 x SlimPAR™ Tri IRC (7 or 12)
1 x Power Cord
1 x Warranty Card
1 x Quick Reference Guide
Unpacking
Instructions
Immediately upon receipt, carefully unpack the product and check the container to make
sure you have received all the parts indicated above in good condition.
Claims
If the container or the material inside the container (the product and included
accessories) appear damaged from shipping, or show signs of mishandling, notify the
carrier immediately, not CHAUVET®, upon receipt. Failure to do so in a timely manner
may invalidate your claim with the carrier. In addition, keep the container and all the
packing material for inspection.
For other issues such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within seven (7) days of receiving
the merchandise.
Text
Conventions
Convention Meaning
1~512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified
Menu > Settings A sequence of menu options to be followed
<ENTER> A key to be pressed on the product’s control panel
ON A value to be entered or selected
Icons
Icon Meaning
This paragraph contains critical installation, configuration, or
operation information. Failure to comply with this information may
render the product partially or completely inoperative, cause
damage to the product, or cause harm to the user.
This paragraph contains important installation or configuration
information. Failure to comply with this information may prevent
the product from functioning correctly.
This paragraph reminds you of useful, although not critical,
information.
Document
Information
The information and specifications contained in this document are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
omissions that may appear in this manual. CHAUVET® reserves the right to update the
existing document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2011 CHAUVET®. All rights reserved
Electronically published by CHAUVET® in the United States of America
Author Date Editor Date
A. Diaz 09/16/11 B. Pillow 09/20/11

SlimPAR™ Tri IRC series User Manual (Rev. 04) Page 5 of 25
Product at a
Glance
Use on Dimmer

Auto Programs

Outdoor Use

Auto-ranging Power Supply

Sound Activated

Replaceable Fuse

DMX

User Serviceable

Master/Slave

Duty Cycle

Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
Always connect the product to a grounded circuit to avoid the risk of electrocution.
Always disconnect the product from the power source before cleaning or replacing
the fuse.
Avoid direct eye exposure to the light source while the product is on.
Make sure the power cord is not crimped or damaged.
Never disconnect the product from power cord by pulling or tugging on the cord.
If mounting the product overhead, always secure to a fastening device using a
safety cable.
Make sure there are no flammable materials close to the product when operating.
Do not touch the product’s housing when operating because it may be very hot.
Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
Always install the product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces.
Be sure that no ventilation slots on the product’s housing are blocked.
Never connect the product to a dimmer.
Make sure to replace the fuse with another of the same type and rating.
Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
The maximum ambient temperature is 104° F (40° C). Do not operate the product at
higher temperatures.
In the event of a serious operating problem, stop using the product immediately.
Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
Keep this User Manual for future consultation. If you sell the product to another
user, be sure that they also receive this document.

Page 6 of 25 SlimPAR™ Tri IRC series User Manual (Rev. 04)
2. I NTRODUCTION
Product Overview (SlimPAR™ Tri 12 IRC)
LEDDisplay
PowerIn
DMXOut
SafetyLoop
DMXIn
Bracket
AdjustmentKnob
FuseHolder
PowerOut

SlimPAR™ Tri IRC series User Manual (Rev. 04) Page 7 of 25
Product Overview (SlimPAR™ Tri 7 IRC)
LEDDisplay
PowerIn
DMXOut
DMXIn
Bracket
AdjustmentKnob
FuseHolder
PowerOut
SafetyLoop

Page 8 of 25 SlimPAR™ Tri IRC series User Manual (Rev. 04)
Product Dimensions (SlimPAR™ Tri 12 IRC)

SlimPAR™ Tri IRC series User Manual (Rev. 04) Page 9 of 25
Product Dimensions (SlimPAR™ Tri 7 IRC)

Page 10 of 25 SlimPAR™ Tri IRC series User Manual (Rev. 04)
3. S ETUP
AC Power
The SlimPAR™ Tri IRC series has an auto-ranging power supply and it can work with an
input voltage range of 100~240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit (circuit breaker or fuse). Make
sure the product has an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
Follow the instructions below to change the fuse, if necessary.
Disconnect the product from the power outlet before replacing the fuse.
1. Wedge the tip of a flat head screwdriver into the slot of the fuse holder and pry out
of the housing.
2. Remove the blown fuse from the holder and replace with a fuse of the exact same
type and rating.
3. Insert the fuse holder back into place and reconnect power.
The product does not ship with a spare fuse; however, the safety cap has room
for a spare.
Always replace a blown fuse with the same type and rating.
Installedfuse
(heldbyplasticclip)
Sparefuseholder
(insidesafetycap)
Safetycap

SlimPAR™ Tri IRC series User Manual (Rev. 04) Page 11 of 25
Power Linking
The product provides power linking via the Edison outlet located in the back of the unit.
Please see the diagram below for further explanation.
PowerLinkingDiagram
You can power link up to 23 SlimPAR™ Tri 7 IRC units on 120 VAC or up to 39
SlimPAR™ Tri 7 IRC units on 230 VAC.
You can power link up to 15 SlimPAR™ Tri 12 IRC units on 120 VAC or up to 26
SlimPAR™ Tri 12 IRC units on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
1
st
Product 2
n
d
Product 3
rd
Product
Otherproducts

Page 12 of 25 SlimPAR™ Tri IRC series User Manual (Rev. 04)
Mounting
Before mounting the product, read and follow the safety recommendations indicated in
the Safety Notes section (page 2 of this manual).
Orientation
The SlimPAR™ Tri IRC series may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
Before deciding on a location for the product, always make sure there is easy
access to the product for maintenance and programming purposes.
Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight. Please see the Technical Specifications section of
this manual for weight information.
When mounting the product overhead, always use a safety cable. Mount the
product securely to a rigging point, whether an elevated platform or a truss.
When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The bracket has a 13 mm hole, which is appropriate for
this purpose.
When power linking multiple products, you must always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
The bracket adjustment knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
The double bracket yoke/mounting brackets/rubber feet/metallic feet also serve as
floor supports/allow for surface mounting. When mounting the product on the floor,
make sure that the product and cables are away from people and vehicles.
MountingDiagram
(SlimPAR™Tri12IRC
shown)
GelFrameHolder
Bracket
AdjustmentKnob
MountingBracket
GelFrame

SlimPAR™ Tri IRC series User Manual (Rev. 04) Page 13 of 25
4.OPERATION
Control Panel
Operation To access the control panel functions, use the four buttons located underneath the
display. Please refer to the Product Overview to see the button locations on the control
panel.
Button Function
<MENU> Press to find an operation mode or to back out of the current menu
option
<UP> Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER> Press to activate a menu option or a selected value
Menu Map Mode Programming Steps Description
3-CH d001-512 3 channel DMX mode (RGB)
7-CH d001-512 7-channel DMX mode
C--
C1 Red
Static color
C2 Green
C3 Blue
C4 Cyan
C5 Magenta
C6 Yellow
C7 White
P--
P1 7 color program (switching)
P2 7 color program (fading)
P3 3 color program (switching)
P4 3 color program (fading)
P-- P5 7 color program (sound active)
P6 3 color program (sound active)
S-- S--1-100 Program speed for P1-P4
U--
A-- Red
(r000-100) Custom Static Colors
Combine red, green, and blue
g-- Green
(r000-100)
b-- Blue
(r000-100)
SEr On Turns infrared on or off
Off

Page 14 of 25 SlimPAR™ Tri IRC series User Manual (Rev. 04)
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you choose a starting address that is too high, you
could restrict the access to some of the product’s channels.
The SlimPAR™ Tri IRC series uses up to 7 DMX channels in its 7-channel DMX mode,
which defines the highest configurable address to 506.
If you are not familiar with the DMX protocol, you may refer to the DMX Primer section in
the Technical Information chapter.
To select the starting address, do the following:
1. Press <MENU> repeatedly until 3-CH or 7-CH shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode (either Static or
Automatic) to a DMX string connected to a DMX controller. Products in standalone
mode may transmit DMX signals that could interfere with the DMX signals from
the controller.
Automatic Mode
To enable the Automatic Mode, follow the instructions below:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to choose an auto program (P1-P6).
4. Press <ENTER>.
5. To adjust the speed of the program, press <MENU> until S-- shows on the display.
6. Press <ENTER>.
7. Use <UP> or <DOWN> to adjust the duration of each step of the automatic program
from S__1 (fast) to S100 (slow).
8. Press <ENTER>.
Static Color Mode
To enable the Static Color Mode, follow the instructions below:
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to choose a color. (C1-C7)
4. Press <ENTER>.
Custom Static
Color Mode
To enable the Custom Static Color Mode, follow the instructions below:
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> to choose between colors (R--, g--, b--).
4. Press <ENTER>.
5. Press <UP> or <DOWN> to choose the intensity of the color (000-100).
6. Repeat the steps to mix additional colors to create the color you need.

SlimPAR™ Tri IRC series User Manual (Rev. 04) Page 15 of 25
Master/Slave
Mode
The Master/Slave mode allows a single SlimPAR™ Tri IRC series unit (the “master”) to
control the actions of one or more SlimPAR™ Tri IRC series units (the “slaves”) without
the need of a DMX controller. The master unit will be set to operate in either Automatic
or Static Color mode, while the slave units will be set to operate in Slave Mode. Once
set and connected, the slave units will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1. Press <MENU> repeatedly until 3-CH shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to 001.
4. Connect the DMX input of the first slave unit to the DMX output of the master unit.
5. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
6. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in either Automatic or Static Color mode.
2. Make the master unit the first unit in the DMX daisy chain.
Configure all the slave units before connecting the master unit to the DMX
daisy chain.
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller may interfere with the signals from the
master unit.
Do not connect more than 31 slave units to the master unit.
Infrared Control
The SlimPAR™ Tri IRC series is fully compatible with the IRC Infrared Remote Control
from CHAUVET®. To enable usage with the IRC, follow the instructions below:
1. Press <MENU> repeatedly until SEr shows on the display.
2. Press <ENTER>.
3. Press <UP> or <DOWN> to turn the feature on or off.
4. Press <ENTER>.
For IRC operation instructions, refer to the following page.

Page 16 of 25 SlimPAR™ Tri IRC series User Manual (Rev. 04)
IRC (Infrared Remote
Control) Operation
Automatic Mode
Automatic Mode will enable you to run the automatic programs on the
product.
To turn on Automatic Mode:
1. Press AUTO on the IRC.
2. Press + or – to choose between the different auto programs.
To adjust the speed of the automatic program:
1. Press SPEED on the IRC.
2. Press %.
3. Press + or – to either increase or decrease the speed of the program.
Sound Active Mode
Sound Active Mode will enable the product to respond to the music.
To turn on Sound Active mode:
1. Press SOUND on the IRC.
To adjust sound sensitivity in Sound Active mode:
1. Press SENSITIVITY on the IRC.
2. Press %.
3. Press + or – to either increase or decrease sound sensitivity.
Manual Color Control
To choose a specific color with the IRC:
1. Press MANUAL on the IRC.
2. Press any number between 0-9 to choose your color.
To manually control the RGB percentage:
1. Press MANUAL on the IRC.
2. Press R, G, or B to choose your color.
3. Press + or – to increase or decrease the percentage of each color.
Miscellaneous Operation
To adjust the strobe rate of the program:
1. Press STROBE on the IRC.
2. Press + or – to increase or decrease the strobe rate.
3. Press STROBE again to turn off the strobe.
To change the switching effect of the program:
Press FADE/SNAP on the IRC.
Fade will slowly switch the effect. Snap will rapidly switch the effect.
To black out the lights:
Press BLACK OUT on the IRC.
This will turn off all the lights until the button is pressed again.
Note: The IRC will not respond to any inputs when Black Out is activated. If
the remote does not respond when a button is pressed, try pressing
BLACK OUT. You may have inadvertently activated BLACK OUT.

SlimPAR™ Tri IRC series User Manual (Rev. 04) Page 17 of 25
DMX Channel Assignments and Values
7-CH Channel Function Value Setting
1 Red 000 255 0~100%
2 Green 000 255 0~100%
3 Blue 000 255 0~100%
4 Color Macros
(overrides CH. 1-3) 000 015 No function
016 255 Color Macros
5
Speed
(when CH.6 is between
032-223) 000 255 0~100%
Strobe 000 015 No function
016 255 Slow to fast
6 Mode
000 031 RGB Mode
032 063 Pulse effect 0%-100%
064 095 Pulse effect 100%-0%
096 127 Pulse effect 100%-0%-100%
128 159 Auto fade transition
160 191 Auto snap transition (3 colors)
192 223 Auto snap transition (7 colors)
224 255 Sound triggering mode
7 Dimmer 000 255 0~100%
3-CH Channel Function Value Setting
1 Red 000 255 0~100%
2 Green 000 255 0~100%
3 Blue 000 255 0~100%

Page 18 of 25 SlimPAR™ Tri IRC series User Manual (Rev. 04)
5. T ECHNICAL I NFORMATION
Product
Maintenance
Dust build up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life. To maintain optimum performance and
minimize wear, you should clean your lighting products at least twice a month. However,
be aware that usage and environmental conditions could be contributing factors to
increase the cleaning frequency.
To clean the product, follow the instructions below:
Unplug the product from power.
Wait until the product is cold.
Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
Clean all glass/transparent surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
Softly drag any dirt or grime to the outside of the glass/transparent surface.
Gently polish the glass/transparent surfaces until they are free of haze and lint.
Always dry the glass/transparent surfaces carefully after cleaning them.

SlimPAR™ Tri IRC series User Manual (Rev. 04) Page 19 of 25
General Troubleshooting
Symptom Possible Cause Possible Action
Circuit breaker or fuse
keeps blowing
Excessive load on the circuit Make sure that the total load does not
exceed 80% of the breaker or fuse
nominal current
Short circuit along the power lines Check the power lines and power cords
Product does not power
up
No energy on power outlet Check power outlet
Change to another outlet
Loose or damaged power cord Check the power cord
Blown fuse Replace blown fuse with a good one of
the same type and rating
Internal problem Send product for repair
Product does not
respond to DMX
Wrong starting address on the
product Set the correct starting address on the product
Use the right fader(s) on the controller
Wrong DMX personality on the
product Set the correct DMX product’s personality
Assign the faders accordingly
Wrong polarity setting on the DMX
controller Change the signal polarity on the controller
Loose or damaged DMX cable Check the DMX cable before the faulty
unit
Internal problem Send product for repair
Intermittent DMX
Problems
Signal cables are not DMX
compatible Replace non DMX cables with true DMX cables
Interference with AC or radio
signals Keep DMX cables away from AC wires or radio equipment
DMX cable too long Install an optically coupled DMX
amplifier right before the product with
intermittent problems
Too many products connected Install an optically coupled DMX
amplifier after unit #32
Terminator not connected Install a terminator, as indicated in the
DMX Primer section.
If you still experience problems after trying the above solutions, contact
CHAUVET® Technical Support.

Page 20 of 25 SlimPAR™ Tri IRC series User Manual (Rev. 04)
Contact
Procedure
In case you need to return a product or request support, follow the procedure below:
If you live in the US, contact CHAUVET® World Headquarters (see below).
If you live in the UK or Ireland, contact CHAUVET® Europe Ltd.(see below).
If you live in any other country, DO NOT contact CHAUVET®. Instead, contact your
distributor of record. Refer to our Web site for contact details of distributors outside
the US, United Kingdom, or Ireland.
CHAUVET®
Contact
Information
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [email protected]
Technical Support
Email: [email protected]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk
If you live outside the US, United Kingdom, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® products to
them. Visit our Web site for contact details.
Returning
Products to
CHAUVET®
Call the corresponding CHAUVET® Tech Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
You must send the merchandise prepaid, in its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write the following information on a piece of paper
and place it inside the box:
Your name
Your address
Your phone number
The RMA number
A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. As a suggestion, proper UPS packing or double-
boxing is always a safe method to use.
CHAUVET® reserves the right to use its own discretion to repair or replace
returned product(s).