Chino DB630E User manual

6-Way Lowboy Console
Standard Features Are:
73FC Transformer
125 Amp 3 Phase Circuit Breaker
Primary 3-Phase Input Tapping options of 480/575v, 3ph,
60hz. Secondary Output Voltage 80 Volt
6 Channel Contactor Switching
Individual Neon Indicators per Channel
Chino Temperature Controllers
Size: 36” high x 34” deep x 24” wide
6” Heavy Duty Casters
4 Eye Hooks

Read Carefully before operating
1) Upon receipt of your new power console, visually inspect it for any damage that
might have occurred during shipment. If there are any signs of damage please
call EHS immediately so a damage claim can be processed.
2) The power console weighs approximately 960 pounds. Be very careful when
loading and unloading using a fork-lift.
3) Never operate the power console with the sides or the top removed. Serious
electrical shock can occur if care is not taken.
4) Always use a primary cable of #4 AWG minimum. Do not use anything smaller
in size. The cable must be 4-Wire and the power console must be grounded at all
times during use.
5) Make sure the primary input taps have been connected in the correct orientation
for the voltage you will be using i.e. 440/480/575 Volts.
6) Make sure the secondary taps have been connected in the correct orientation for
the heaters you will using i.e. 80 Volts.
7) If you should have any questions please call us 24 hours a day, 7 days a week, at
our office # [phone].
Getting Started set up Procedure
1) Make sure that all primary power connections are tightened and properly connected.
Make sure that the unit is grounded and that the supply power is connected to the
correct input taps.
2) Connect the triple cable sets to the output camlocks. Make sure the corresponding
thermocouples (T/C) are plugged into the proper T/C jacks.
NOTE !! When attaching the thermocouples to the work-piece or reattaching a broken
thermocouple, it is very important to temporarily disconnect the T/C from the jack on
the console and the jack on the recorder. The electrical spark of the TAU may travel
through the T/C wire and cause damage to the recorder or the controller.
3) Turn power on to the console.

1 1
N.T.S.
RDR 12/08/17
CHINO RAMP
6-WAY POWER CONSOLE
0
HEAT
CONTROLLERS STANDARD MINI ME

1 1
N.T.S.
6-LOW WIRING SCHEMATIC
CMM 1/11/13
CHINO RAMP CONTROLLERS
6-WAY POWER CONSOLE
1
1301-013A
HEAT
STANDARD LOWBOY
1SHUNT WIRING RDR 10/13/16

DB630E-Ramp Instruction Manual
* This controller is designed for heat treatment market
Ver. 2014/7
PV : Process Value
(Current Temperature)
SV : Set Point
(Current Target Set Point)
Percentage of Output
No sensor connection
-----
The controller will begin to ramp to the set point
and will be display this mark [ ▲].
If the controllers is no display [ ▲] then it is
not ramping!
A. To run the controller * Control sample
*
This is asking for a value RATE to be chosen for Ramp Rate.
1
Press [ ＞ ] key to show under cursor.
2
Using [ △ ] , [ ▽ ] keys to change the value to the desired
Ramp Rate. Blinking the changed value. ( Value/Hours )
3 Make sure to press [ENT] key to confirm.
* If you want to straight to Set Point, must be set "0".
*
This is asking for a SP value to be chosen for the End-Set-Point. Manual Output Home Display
1
Press [ ＞ ] key to show under cursor.
(0 to 100%)
PV/SV
2Using [ △ ] , [ ▽ ] keys to change the value to the End Set Point.
3 Blinking the changed value. Make sure to press [ENT] key to confirm.
*
When blinking "RUN" at the status, press [ENT] key to start ramping
from the input temperature to the set point at the chosen ramp rate.
Ramp Rate
* Press [MODE] key to only return to HOME display.
Ex. (400F/Hour)
*
While the controller is running, you can use following command.
"RUN" : Run the controller that is paused.
"SKIP" : Skip to the End Set Point of ramping control.
"PAUSE" : Pause the current set point.
"OFF" : Turn the controller OFF.
End Set Point
B. To manual out put mode. Ex. (800F)
* This indication is "Manual Output Mode".
1
The MAN indication LED is ON.
2The percentage can be changed any time using [ △ ] , [ ▽ ] keys.
3 You can return to automatic control mode by pressing and Current Status
holding [ ＞ ] key for 3 seconds. Run/Off/Pause/Skip
* For the example if the controller percentage is set to 50% the cycle
will be on and off per approximately 4 sec. If the controller
percentage is set to 75% the cycle will be on for approximately
6 sec. and will be off for approximately 2 seconds.
Operation chart
Show under cursor for selecting the values manually.
Return to HOME display
RUN
800F
77F
Display
PAUSE
Blink
1
Solid
2
Solid
MAN
Solid
RA
RUN
Solid
PAUSE
Blink
LED
Solid
Hold
3 sec.
Any parameter changes, make sure to press [ENT] Key to confirm
Change value and parameters
Change to "Manual output mode"
Additional Notes
Additional Notes
Do This
Do This
Display
1. Press
2. Press
3. Press
Display
Status
OFF
Go to next parameters
Key Feature : There are five keys on the face of the DB630 controller
PAUSE the controller by DI
Alarm 2 Active
Alarm 1Active
Output 100%
Output 0%
-----
Output 50%
----------
RAMP Model (Stay ON)
MANUAL output mode is ON
PAUSE the controller
RUN the controller
Status
Hold
Hold
400F /
A
B
Current
Temp
A
B