Christie Vivid Blue 38-VIV301-01 User manual

AIR FILTER CARE AND CLEANING
Turn power off, and disconnect AC power cord from
an AC outlet.
1
2
Air Filter prevents dust from accumulating on a surface of Projection Lens and Projection Mirror. Should Air
Filter become clogged with dust particles, it will reduce Cooling Fans' effectiveness and may result in internal
heat build up and adversely affect life of projector.
Clean Air Filters every 250 hours of operation, following steps below:
3
4
CAUTION
Do not operate a projector with Air Filter
removed. Dust may accumulate on LCD
Panel and Mirror degrading picture quality.
Do not put small parts into Air Intake Vents.
It may result in malfunction of a projector.
RECOMMENDATION
Avoid dusty/smoky environments when operating a projector. Operation in such environments
may cause poor image quality. In any environment, clean the filters every 250 hours of operation.
When using under dusty or smoky conditions, dust may accumulate on liquid crystal panel, lens, or optical elements inside it.
This condition may degrade quality of projected image.
When above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.
Pull out 3 Air Filters and Air filter Covers from a
projector.
Clean each parts (Air Filter and Air filter Cover) with
brush or wash out dust and particles. Be sure to dry
them out.
Replace Air Filter and Air Filter Cover properly. Make
sure that they are fully inserted.
BOTTOM OF PROJECTOR FRONT OF PROJECTOR ** SIDE OF PROJECTOR
AIR FILTER
AIR FILTER
COVER AIR FILTER
AIR FILTER
COVER
AIR FILTER
AIR FILTER
COVER
** NOTE: Reverse fan to EXHAUST and remove front filter, if present. Only the bottom and side filters are required.
** Bottom filter #10-A6102923162 Side filter #10-A6102923186
No longer used. Reverse fan to exhaust!

Check number of lamp to be replaced on Lamp Status
Display.
Loosen 3 screws on Lamp Cover and remove Lamp Cover.
(See right figure.)
1
3
Loosen 2 screws and pull out Lamp Assembly to be replaced
by grasping handle.
4
Turn off a projector and disconnect AC Power Cord. Allow a
projector to cool for at least 45 minutes.
2
Replace Lamp Assembly with a new one and tighten 2 screws.
Make sure that Lamp Assembly is set properly
6
Follow these steps to replace lamp assembly.
Replace Lamp Cover and tighten 3 screws.
5
7
8
Connect AC Power Cord to a projector and turn projector on.
Reset Lamp Replacement Counter. (See "Lamp Counter
Reset" on the following page.)
NOTE : Do not reset LAMP REPLACEMENT COUNTER
when a lamp is not replaced.
CAUTION : DO NOT OPERATE PROJECTOR IF A LAMP IS REMOVED. IT MAY
RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.
SCREWS
LAMP
COVER
SCREWS
ORDER REPLACEMENT LAMP
Replacement Lamps can be ordered through your dealer. When ordering, provide the following
information to your dealer. Each kit contains one lamp.
Model No. :38-VIV301-01 = VIVID Blue Lamp Replacement Kit #03-900471-01P
Determine which lamp needs to be replaced
according to Lamp Status Display (both recommended).
Figure shows case of replacing LAMP 2.
LAMP 1
LAMP 2
NOTES ON LAMP REPLACEMENT
To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing
BOTH lamps at once. Consult your projector's manual regarding all other lamp issues.
LAMP REPLACEMENT
CAUTION
Do not drop a lamp assembly or touch a glass
bulb! Glass can shatter and may cause injury.
CAUTION
For continued safety, replace with a lamp
assembly of same type.
Allow a projector to cool for at least 45
minutes before you open Lamp Cover. Inside
of a projector can become very hot.
:38-MX2001-01 = Matrix 2500 Lamp Replacement Kit #03-000748-01P
:38-RS1001-xx = RoadRunner L6 Lamp Replacement Kit #03-900471-01P
:38-VIV302-01 = RoadRunner LX65 Lamp Replacement Kit #03-000708-01P
:38-VIV210-01(2) = LW40(u) Lamp Replacement Kit #03-000761-01P

Lamp counter reset
Move pointer to Lamp counter reset and then
press SELECT button. Move arrow to
replaced lamp number (Lamp 1 or Lamp
2) and then press SELECT button.
Be sure to reset Lamp Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP
REPLACE indicator stops lighting.
Turn projector on, press MENU button and ON-SCREEN
MENU will appear. Press POINT LEFT/RIGHT button(s) to
move a red frame pointer to SETTING Menu icon.
1
Press POINT DOWN button to move a red frame pointer to
“Lamp counter reset”and then press SELECT button.
2
Do not reset Lamp Replace Counter except after Projection lamp is
replaced.
Another confirmation dialog box appears and select [Yes] to
reset Lamp Replace Counter.
4
Move arrow to replaced lamp number (Lamp 1 or Lamp 2) and
then press SELECT button. Message "Lamp replace counter
Reset?" is displayed. Move pointer to [Yes] and then press
SELECT button.
3
NOTE: Be sure to reset correct lamp number otherwise LAMP
REPLACE indicator continues lighting.
Message "Lamp replace counter Reset?" is
displayed. Move pointer to [Yes] and then
press SELECT button.
Closes SETTING MENU.
Quit
1 2