Christie 140-133108 Series User manual

Ultra short throw lens
installation
The ultra short throw lens—0.36 UST GS (P/N: 140-133108-XX)—allows you to position your projector
as close as possible to your screen or display.
Unless otherwise indicated, the 700-GS and 850-GS model is shown for illustration purposes and may
vary from your model.
Affected products
The following products are affected:
• Christie DHD630-GS
• Christie DWU630-GS
• Christie DHD635-GS
• Christie DWU635-GS
• Christie DHD850-GS
• Christie DWU850-GS
• Christie DHD700-GS
• Christie DWU700-GS
• Christie DHD1075-GS
• Christie DWU1075-GS
Required components
The ultra short throw lens (P/N: 140-133108-XX) includes the following components.
Quantity Description
1 0.36 UST GS lens
1 Boresight adapter plate
1 Lens support bracket
1 Lens bracket
2 Mounting blocks (A)
2 Mounting blocks (B)
1 Angle bracket
Ultra Short Throw Lens Installation Instruction Sheet 1
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

Quantity Description
3 Boresight extension rods
1 Boresight L-shaped socket key
12 M3x8 screws
6 M3x8 hex screws
4 M6x22 screws
4 M6x55 screws
4 M6x65 screws
6 M3 washers
10* M6 washers
1 Product information card
* Six of the washers are provided as spare parts.
Required tools
The following tools are required.
• Long neck #2 Phillips screwdriver
• L-shaped socket key provided with the lens kit
• 2.5 mm allen key
• 5 mm hex nut driver
• 10 mm hex key wrench
Upgrading projectors to version 1.1.0 or newer
software
Christie is continuously improving the GS Series product line. To make sure you are getting the best
experience, version 1.1.0 or newer software is mandatory for the ultra short throw lens application.
For 1075-GS, 630-GS, and 635-GS, the current firmware version is compatible with the ultra short throw
lens application.
1. To download version 1.1.0 or newer of the new GS Series software, go to https://
www.christiedigital.com/en-us/business/products/projectors/1-chip-dlp/gs-series.
2. From the Overview tab, select the appropriate projector model.
3. Select Downloads > Software Downloads.
4. Under Christie GS Series Software (Version X.X.X), click Download.
Where X.X.X is version 1.1.0 or newer.
5. Install the software and reboot the projector.
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 2
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

Completing the ultra short throw lens installation
setup
To complete the installation setup, enter UST mode and start a lens calibration.
1. If you have a non-ultra short throw lens, complete the following steps:
a) Install a non-ultra short throw lens in the projector.
b) Power on the projector.
c) Access the Service menu.
• For the GS Series 700/850/1075 models: From the on-screen display, select
Configuration > Service.
• For GS Series 630/635 models: From the on-screen display, select Settings >
Service.
d) Enter the Service password.
e) Click OK.
f) Start the ultra short throw lens installation.
• For the GS Series 700/850/1075 models: Select UST Lens Install > Start.
• For GS Series 630/635 models: Select Lens Install > Start.
A lens calibration is performed.
2. If you do not have a non-ultra short throw lens, complete the following steps:
a) Connect to the projector with a computer using RS232 or Ethernet.
The default IP address is 192.168.0.100.
b) Send the following two serial API commands to the projector to enter UST mode:
(UID "service,service")
(UST 1)
A lens calibration is performed.
3. When the lens calibration is complete, to turn off the projector, press Exit.
4. Disconnect the projector from AC power.
Removing the non-ultra short throw lens
Use the correct method to remove the non-ultra short throw projection lens, if it is installed.
If a non-ultra short throw lens is not installed, proceed to Replacing the boresight adapter (on page
4).
1. To remove the lens, press the Lens Release button and rotate the lens counterclockwise by a
quarter to release the lock.
700-GS, 850-GS, and 1075-GS:
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 3
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

630-GS and 635-GS:
2. Remove the lens through the front of the projector.
Replacing the boresight adapter
As part of the ultra short throw lens installation, replace the boresight adapter.
1. For 630-GS and 635-GS only, release the lens ring by turning the lens ring counterclockwise.
2. Remove the three screws securing the standard boresight adapter.
Retain the three screws to use with the new ultra short throw lens boresight adapter.
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 4
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

3. Rotate the standard boresight adapter and remove from the projector.
When removing the boresight adapter, ensure it does not scratch the aperture casing of the
projector.
4. Retain the standard boresight adapter for future use.
5. Disconnect the connector from the plate the boresight adapter rests on.
If in a poorly lit area, stand the projector with the projector aperture facing up for better
visibility of the connector.
6. Insert the new ultra short throw lens boresight adapter in the projector.
When inserting the new boresight adapter, ensure it does not scratch the aperture casing of
the projector.
7. Install and tighten the three screws.
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 5
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

8. Install the connector that you disconnected in step 4 in the new boresight adapter.
Mounting the lens support bracket
To provide additional support for the ultra short throw lens, mount it on a support bracket.
1. Place the ultra short throw lens on a cushioned surface to prevent damaging the lens.
2. Using two M3x8 screws, secure the lens bracket to the ultra short throw lens.
Note the direction of the arrow on the lens bracket.
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 6
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

3. Place the projector upside-down on a flat, clean surface.
4. For 630-GS and 635-GS only, to ensure there is enough clearance between the lens support
bracket and the surface the projector is on, rotate each projector foot nine counterclockwise
turns.
5. Align the mounting block to the lens support bracket.
• For 700-GS, 850-GS, and 1075-GS, align the screw holes on mounting block A to the holes
marked A on the lens support bracket.
• For 630-GS and 635-GS, align the screw holes on mounting block B to the holes marked B
on the lens support bracket.
6. Install four M3x8 screws to secure the mounting block to the lens support bracket.
700-GS, 850-GS, and 1075-GS:
630-GS and 635-GS:
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 7
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

7. To secure the angle bracket to the lens support bracket, install one M3x8 hex screw and one
M3 washer.
Do not fully tighten the screw.
8. For 630-GS and 635-GS only, install the rubber spacer provided in the installation kit on top of
the default rubber spacer on the lens support bracket.
The additional rubber spacer is not required for 700-GS, 850-GS, and 1075-GS.
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 8
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

9. If not mounting the projector using Christie One Mount, complete the following steps:
a) Attach the lens support bracket assembly to the bottom surface of the projector.
b) Install the two M6x22 hex screws and two M6 washers in the mounting holes of the
projector.
700-GS, 850-GS, and 1075-GS:
630-GS and 635-GS:
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 9
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

c) Continue with the last step in this procedure .
10. If using the lens support bracket with Christie One Mount, complete the following steps:
a) Place the lens support bracket assembly on the bottom of the projector.
b) Position two pillars of Christie One Mount to the lens support bracket and the other two
pillars on the projector as shown below.
c) To fasten the two rear pillars of Christie One Mount to the projector, install the two M3x8
hex screws (no washers required) provided with Christie One Mount.
d) Fasten the two front pillars of Christie One Mount to the lens support bracket assembly.
• For 700-GS, 850-GS, and 1075-GS, install the two M6x65 screws and two M6
washers.
• For 630-GS and 635-GS, install two M6x55 screws.
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 10
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

11. Turn the projector back to its original orientation.
12. Install the three extension rods.
The boresight extensions rods must be installed before installing the ultra short throw lens.
Initially adjusting the boresight screws
Before installing the ultra short throw lens, Christie recommends initially adjusting the boresight. Once
the lens is installed, the adjustment range is limited.
1. Confirm the boresight screws are in their initial position with the blue marks aligned as shown.
2. If the boresight screws are not in their initial position, turn the screws counterclockwise until
they stop and then turn the screws clockwise until the blue marks are aligned as shown above.
3. Adjust the boresight to the recommended ranges according to the projector orientation.
For DHD700-GS, DWU700-GS, DHD850-GS, and DWU850-GS:
Orientation Adjustment range (in turns) for boresight screws
A B C
Table top 3 + 1/4 9 9
Portrait (right) 6 + 3/4 7 10 + 3/4
Portrait (left) 5 + 1/4 10 + 3/4 6
Ceiling mount 10 + 1/2 7 + 1/4 7 + 1/4
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 11
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

Orientation Adjustment range (in turns) for boresight screws
A B C
Upright 10 + 3/4 8 + 1/4 8 + 1/2
For DHD630-GS, DWU630-GS, DHD635-GS, DWU635-GS, DHD1075-GS, and DWU1075-GS:
Orientation Adjustment range (in turns) for boresight screws
A B C
Table top 3 + 3/4 7 + 1/2 8 + 1/2
Portrait (right) 5 + 1/4 4 10
Portrait (left) 5 + 1/4 9 + 1/2 4 + 1/2
Ceiling mount 7 + 1/4 6 6
Upright 7 + 1/2 7 7 + 1/4
Installing the ultra short throw lens
Install the ultra short throw lens in the projector after installing the new boresight adapter.
1. Insert the ultra short throw lens into the projector slightly angled to the left so the Top label on
the lens aligns with the Status LED indicator on the projector.
Note the orientation of the lens (1) as illustrated below.
2. To lock the lens, rotate the lens clockwise (2 in the image below).
Turning on the projector
Before turning on the projector, ensure the ultra short throw lens has been installed.
1. Plug the projector into AC power.
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 12
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

2. To turn on the projector, press the Power button.
Adjusting the boresight
The boresight adjustment range changes depending on the orientation of the projector.
When adjusting the boresight with the internal test pattern, only limited lens shift can be performed
and source input is not allowed.
1. Note the location of each the boresight screw before continuing with this procedure.
2. To display a test pattern to assist with adjusting boresight, press TEST.
Four internal test patterns are available.
3. To switch to the next test pattern, press TEST.
4. To exit the Test pattern menu, press Exit.
To access the boresight test pattern after pressing Exit from the popup window, go to the
Service menu.
• For 700-GS, 850-GS, and 1075-GS, to enable the boresight adjustment mode, from the
on-screen display select Configuration > Service > UST Lens Install > Test Pattern 1
to 4.
• For 630-GS and 635-GS, to enable the boresight adjustment mode, from the on-screen
display select Settings > Service > Lens Install > Pattern 1 to 4.
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 13
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

5. Using the L-shaped socket key, adjust the three boresight screws (A, B, and C in the image in
Step 1) counterclockwise until tight.
6. To adjust the boresight for optimized image quality, use the L-shaped socket key.
a) To focus the center of the screen, adjust the floating and back focus.
To adjust the floating focus, press FOCUS. To adjust the back focus, press ZOOM.
b) To focus the left area of the screen, adjust the B boresight screw.
c) To focus the right area of the screen, adjust the A boresight screw.
d) To focus the top area of the screen, press FOCUS.
e) To focus the bottom area of the screen, adjust the C boresight screw.
7. To complete the installation of the lens support bracket, install two M3x8 hex screws and two
M3 washers to secure the lens bracket to the lens support bracket assembly.
8. Tighten the center M3 screw.
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 14
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

9. For 630-GS and 635-GS only, Christie recommends installing the rubber boot.
Christie recommends keeping the boresight extenders in place in case you need to adjust boresight
again.
Removing the ultra short throw lens
A long neck screwdriver is required to release the lens.
1. Loosen the screws that connect the lens bracket to the lens support bracket assembly.
2. Insert the screwdriver into the lens aperture, aligning the screwdriver with the bottom side of
the lens.
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 15
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

3. To remove the lens, with the screwdriver press the Lens Release button (shown below) and
rotate the lens counterclockwise by a quarter.
4. Remove the lens through the front of the projector.
5. If installing a non-ultra short throw lens in the projector:
a) Remove the new boresight adapter and install the original standard boresight adapter.
Repeat the steps in Replacing the boresight adapter (on page 4) in reverse order.
b) Install the non-ulra short throw lens.
c) From the on-screen display, select Configuration > Service.
d) Enter the Service password.
e) Click OK.
f) Select UST Install > None.
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 16
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

A lens calibration is performed and the projector is ready to use with the non-ultra short
throw lens.
Ultra short throw lens specifications
Learn about the specifications for the ultra short throw lens.
Description Value
Throw ratio (0.67" WUXGA, 0.65" 1080P) 0.361 (120")
Focal length 9.49 - 9.55
F number 2.4
Zoom ratio No zoom
Throw distance (0.67" WUXXGA) 0.96 - 2.65 m
Throw distance (0.65" 1080P) 0.99 - 2.72 m
Screen size 120" to 350" (305 to 889 cm)
Lens configuration 23 group 23 elements
Brightness ratio 76.5%
Net weight 2.715 kg (5.986 lbs)
The throw ratio is for screen size 120". The tolerance is +/- 3%.
Ultra short throw lens installation
Ultra Short Throw Lens Installation Instruction Sheet 17
020-102569-05 Rev. 1 (11-2019)
Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.