Chuango G5 User manual

Printed in Hong Kong
PA: OI-G5/EN-Oct.2012-V1.0
GSM Alarm System

GSM Alarm System
FCC Statement

Features Control Panel Layout
2
1
ARM + Auror CPU
Support 10 remote controls, 50 wireless sensors
and 50 RFID tags
Built-in 1,000,000 RF codes combination
maintains high reliability
Cellular communicator, simple operation
Store 5 phone numbers, 1 speed-dial number,
and 1 RFID SMS notification number
Exit and entry delay
SMS alert for low battery of two-way accessories
Arm and disarm the system by SMS or free phone call
Remote monitoring site via phone
Built-in loud speaker for siren and two-way talking
Built-in two pieces of 800mAh lithium batteries
enable 5-hour standby
SMS alerts for power failure, power recovery
and low battery
850/1900MHz GSM frequency,
applicable for universal
GSM Signal Indicator
GSM network searching: Flashes once every second
GSM signal in normal: Flashes once every two seconds
Touch Keypad
Status Indicator
RFID Reader / Play Voice Memo
Stay Arm (Home Mode)
Disarm
Arm
Call
Record Voice Memo /
Connect Button

Bottom
4
3
Arm
Home mode
Disarm on keypad:
Disarm by RFID tag:
Press to arm the system.
Press to arm the sytem in home mode.
All the sensors in Normal Zone are armed except those in
Home Mode Zone which are disarmed so that user can move
freely at home.
Input 4 digits password (default:1234) , and press to disarm
the system after one beep.
If three beeps are heard, password is wrong and
please input again.
Induce the RFID tag to the RFID Reader area to
disarm the system.
MIC
Buzzer
Back-up Batteries
Loudspeaker Tamper Switch

Record / Play Voice Memo
Press to record 10 seconds voice messages.
Or send SMS to system for calling back to record the
voice messages. The Play Voice Memo Button will be
flashing in purple to remind you. Users can touch the
center of circle to listen to the voice memo. The LED
indicator blacks out when the voice memo is played.
Replay by touching it again.
6
5
Bottom
SIM Card Slot
Power On/Off
Input for Wired Sensors
(24-hour zone)
Output for
Electronic Lock
Adapter Interface
Output for Wired Siren
≤ 500mA
Input for Wired Sensors
(normal zone)

8
7
Speed Dial
Phone Call
Electronic Lock Output
Press Call Button , the panel auto dials to pre-stored
phone number of the host, the LED blacks out after talk.
User can also press Call Button to end talk.
Dial phone number and then press Call Button to
start talk, the LED blacks out after talk.
User can also press Call Button to end talk.
When system is disarmed, the output signal opens
electronic lock automatically.
SMS Operation
?
Insert a SIM card to the control panel,
then send a text of to the SIM card number,
the operation guide message will be replied.
You can control the alarm system by
following the guide message:
“?”
System replies first grade guide menu:
‘0’ Disarm
‘1’ Arm
‘2’ Home mode
‘3’ Two-way talk
‘4’ Call-back voice memo
‘00’ Settings inquiry
‘??’ Store phone and SMS No.
Send:

10
9
???
System replies third grade guide menu:
‘91~99’ Zone name
‘10’ RFID tags SMS notice
‘11’ Entry and exit delay time
‘12’ Siren volume and ringing time
‘13’ Disarm password
‘14’ Single zone delay time
Send:
??
‘5’ Store alarm phone No.
‘6’ Store alarm SMS No.
‘7’ Store SMS No. for RFID tags
‘8’ Store speed dial phone No.
‘???’ System setups
System replies second grade guide menu:
Send:
0
Disarm
Send:
System disarmed.

Arm
Stay Arm (Home Mode)
12
11
2
Send:
System in home mode.
1
Send:
System armed.
4
3
Two-Way Talk
Send to the SIM card number, the alarm will call back.
Pick up the phone and start two-way talk.
‘3’
Call-Back to Record Voice Memo
Send to the SIM card number, the alarm will call back.
Pick up the phone, and leave 10 seconds message.
The panel will hang up after 10 seconds.
‘4’
Send:
Send:

Settings Inquiry
14
13
00
System status
Entry and exit delay time: 0sec
Single zone delay time: 30sec
Siren volume: 2
Siren ringing time: 5min
Disarm password: 1234
Send:
Note:
Value of default setting will be changed
once users finish programming.
5
Send:
Store Alarm Phone No.
TEL:
1.
2.
3.
4.
5.
TEL:
1. 67890033
2. 67890022
3. 67890011
4. 67890000
5.
Forward > Edit
Store alarm phone No.
successfully.

Store Alarm SMS No.
16
15
6
Send:
SMS:
1.
2.
3.
4.
5.
SMS:
1. 67890033
2. 67890022
3. 67890011
4. 67890000
5.
Forward > Edit
Store alarm SMS No.
successfully.
Note:
Only after SMS No. is stored, and the
RFID tags SMS notice is changed, users
can receive notice SMS once someone
disarms the system by RFID tag.
7
Store SMS No. for RFID tags
Send:
Forward > Edit
Store SMS No. for RFID
tags successfully.
SMS No. for RFID tags
(0-20 digits):
1.
SMS No. for RFID tags
(0-20 digits):
1. 67890033
Note: Only after SMS No. is stored, and the RFID tags
SMS notice is changed, users can receive notice SMS
once someone disarms the system by RFID tag.

Store Speed Dial Phone Number
18
17
8
Send:
Speed dial phone number
(0-20 digits):
1. 67890033
Forward > Edit
Store speed dial phone
number successfully.
Speed dial phone number
(0-20 digits):
1.
91
Change Zone Name
Special Tips!
st th
Users can change the 1 ~ 9 zone names. The zone name should be 30
English characters at most for each line due to SMS character limit.
Other alarm zones are fixed as Zone 10 alarm, Zone 11 alarm and so on.
Send: 91~99
Zone1 name: Zone 1 alarm
Zone1 name: Entrance door sensor
Forward > Edit
Change zone name
successfully.

SMS Alert for Low Battery of Accessories
(available for two-way accessories such as DWC-102 and PIR-900/910)
SMS will be sent for 1-9 zones with its zone name as
“Zone name + low battery”.
SMS alert for 10~50 zones will be “Zone number + low battery”.
(available for two-way accessories such as DWC-102 and PIR-900/910)
SMS will be sent for 1-9 zones with its zone name as
“Zone name + tamper alarm”.
SMS alert for 10~50 zones will be “Zone number + tamper alarm”.
20
19
Bedroom PIR tamper
alarm.
Zone 10 tamper alarm.
Zone 10 low battery.
Bedroom PIR low battery.
SMS Alert for Tamper Alarm of Accessories
10
Change RFID Tags SMS Notice
Send:
Change RFID tags SMS
notice:
1.
2.
3.
4.
Change RFID tags SMS
notice:
1. Tom
2. Nurse
3. Nancy
4. David
Forward > Edit
Change RFID tags SMS
notice successfully.
Note:
Only after SMS No. is stored, and the
RFID tags SMS notice is changed, users
can receive notice SMS once someone
disarms the system by RFID tag.

11
Entry and Exit Delay Time
Send:
Entry and exit delay time
(0-300 sec.):
0
Entry and exit delay time
(0-300 sec.):
10
Forward > Edit
Notice!
If users don’t want to take remote control or RFID cards with them,
this function can be used. Once the delay time is set, when you arm the system,
one beep will be heard every second to remind the user to leave.
The reminding rhythm will be speeded up in the last 15 seconds.
Once the intruder is detected, the alarm will be delayed accordingly.
22
21
Set delay time
successfully.
12
Siren Volume and Ringing Time
Send:
Siren volume(0 Mute,
1 Low, 2 High):
2
Siren ringing time(1-9min):
5
Forward > Edit
Set siren volume and
ringing time successfully.
Siren volume(0 Mute,
1 Low, 2 High):
1
Siren ringing time(1-9min):
3

13
Disarm Password
Send:
Disarm password(4-6 digits):
1234
Disarm password(4-6 digits):
8888
Forward > Edit
24
23
Set disarm password
successfully.
14
Single Zone Delay Time
Send:
Single zone delay time (0-300 sec.):
30
Single zone delay time (0-300 sec.):
15
Forward > Edit
Set single zone delay time
successfully.

0086
0001
Change System Language
Send: 0086 to change language to be Chinese
Send: 0001 to change language to be English
26
25
Set English successfully.
中文语言修改成功!
21
22
Delete Wireless Accessories by SMS
Send:
Send:
Delete RFID Tags by SMS
Or press Tamper Switch 3 times within 3 seconds,
accessories will be cleared after two beeps.
Delete wireless accessories
successfully.
Delete RFID tags
successfully.

0000
Restore System to Default Setting by SMS
Send:
28
27
System has been restored
to factory settings.
Note:
After programming, only stored numbers can send SMS to
restore the system.
Or press Tamper Switch 5 times within 3 seconds,
the system will be restored to factory settings after
two beeps.
Arm & Disarm by Free Phone Call
Connect Wireless Accessories & RFID Tags
Arm
Disarm
Call the control panel number, hang up when hearing
the ring tone. The panel will call back. The user hangs
up the phone directly to arm the system.
Call the control panel number, hold on until the panel
hangs up the call.The panel will not call back. System
is disarmed.
Input 4-6 digits password, press Connect Button ,
the LED indicator lights up, then trigger the accessory
or RFID tag once within 15 seconds, the connection is
successful after a beep.
Once two beeps are heard, the accessory has been
connected before. The first connected accessory is in
Zone 1, the second one in Zone 2, and so on.

30
29
Connect Wireless Siren
The newly-added wireless siren can be used after
connecting to the control panel.
Press the Connect Button of the wireless siren for 0.5 second,
the Connect Button LED indicator lights on, and then press
the Arm Button on the control panel, the siren will be
connected after one beep is heard.
Testing: Press the Arm Button on the remote control, to make
sure that the internal siren and wireless siren both beep once,
the connection is successful. If not, the connection fails,
please reconnect them.
Once the intruder is detected, both internal siren and wireless
siren will hoot to deter the illegal intruder. (The siren will be
off in 5 minutes as the default setting). At the same time, the
alarm system will send SMS and auto dial to users.
Operation:
Specifications
GSM Alarm System
CG-G5
Input: AC 110-240V/50-60Hz
Output: DC 12V/500mA
850/1900MHz
110mA
340mA
Lithium Battery : 3.7V/800mAh x 2 PCS (BL-5B)
105dB
10pcs remote controls, 50pcs wireless accessories,
and 50pcs RFID tags.
Product name :
Model No. :
Control panel’s power supply :
GSM working frequency :
Standby current :
Alarm current :
Internal battery backup :
Internal siren :
Allowed amount of expandable wireless accessories

Radio frequency
Housing material
Operation condition:
Size (L x W x H) :
ABS plastic
Temperature: -10ºC~55 ºC
Humidity: ≤ 80%(non-condensing)
Panel : 188×132×26mm
32
31
315.8599MHz & 125KHz