Chuango OV6 User manual

OV6
WiFi Alarm System
User Manual

Foreword
Thank you for purchasing the OV6 alarm system. Please unpack the product,
familiarize yourself with the component parts, and carefully read through the
instruction guide before installation.
The installation must be completed in the order shown in the guide to ensure a
successful installation.
Disclaimer
All statements, technical information and recommendations in this manual
are believed to be reliable, but the accuracy and completeness thereof are not
guaranteed or warranted.
The specications and information regarding the products as shown in this
document is subject to change without notice.
The reproduction, language translation modication, storage in a retrieval system or
re-transmission, in any form or by any means, electronic, mechanical or otherwise,
is strictly prohibited without prior written permission.
In no event are we liable for any indirect, special, incidental, or consequential
damages, including, without limitation, lost prots or loss or damage to data arising
out of the use or inability to use this document.

Contents
Packing List ............................................................................................................................................1
Hub ......................................................................................................................................................2~3
Remote Control .....................................................................................................................................4
Door/Window Contact .......................................................................................................................5
Getting Started ................................................................................................................................. 6-8
App Control and Settings ...........................................................................................................9-18
Installation ..................................................................................................................................... 18-19
Replacing Accessory Batteries ......................................................................................................20
Restoring to Factory Settings ........................................................................................................21
Specications ............................................................................................................................... 21-22

1
Packing List
1x Smart Hub
Battery of the Hub*4 1x DWC-102 Door/ Window Contact
1x RC-80 Remote Control 1x Power Adapter 1x Reset Pin

1 2
Hub
All Sensors are wirelessly linked to the Hub.
In the event of alarm activation, for example, when a Sensor is triggered, a push
notification will automatically be sent to you and other pre-authorized users.
The system can be controlled and monitored both on-site using the remote control
supplied and remotely with the Smart Life app on the App Store and Google Play.
The system can easily be expanded to include up to 50 wireless sensors and 10
remote controls.
Top View
LED Indicator
Bottom View
Pairing Button
AC Adapter Jack
Speaker
Network
Conguration Battery

3
LED Indication
Rapid ashing yellow The hub is connecting with the network
through EZ Mode.
Slow ashing yellow The hub is connecting with the network
through AP Mode.
Alternating red, blue, and green The hub is pairing with an accessory
Flashing once per second Searching for a network or disconnected
from router
Off The power adapter is not plugged in
Red System is Armed (Away Mode)
Blue System is in Home Mode (Part Arm)
Green System is Disarmed
Rapid ashing red Alarm condition
Flashing once per 3 seconds Low battery
Note: The Hub must be plugged in to the Power Adapter in order to maintain the WiFi
connection.
When AC power is lost, the Hub will last for 2 minutes to send out a push notication to the
connected smartphones, and the sounder will keep beeping for 30 seconds.

3 4
Remote Control
The remote control can be used to Arm (Away Mode), Home Arm, and Disarm the
system. It can also be used to trigger an emergency alarm (SOS) manually.
Status Indicator
Disarm
Arm (Away Mode)
Home Arm
(Part Arm) SOS Button
Arm (Away Mode)
Status Indicator
Disarm
SOS Button
Home Arm
(Part Arm)
Button System Status
Sets the system to Arm (Away mode). Set to this mode when the property is
unoccupied.
Sets the system to Disarm mode. No sensors will trigger the alarm.
Note: When system is set to ‘Disarm’, all re, smoke, and gas leakage sensors (purchased
separately) will remain active as they are factory set to 24-Hour Zone
Sets the system to Home mode. Sensors that are set to the Disarmed Zone
will not be Armed while all the others will be Armed. This mode allows a
select set of sensors (for example, door/window contacts) to be Armed,
allowing the occupier freedom of movement within the property.
The SOS Button will trigger the alarm and send an alert notication to
registered users regardless of the hub mode.
Press the [ ] button. After the indicator on the remote control blinks
once, press [ ] button within 3 seconds to mutely arm the system.
Press the [ ] button. After the indicator on the Remote Control blinks
once, press [ ] button within 3 seconds to mutely disarm the system.

5
Door/ Window Contact
Door/window contacts are set to ‘Armed’ zone by default and are ideal for
protecting entry/exit points such as front doors, back doors, and windows. When
the system is Armed (Away Mode) and the door/window contact is triggered
(magnet separated from the transmitter), the hub internal siren will sound
immediately and send a push notication with the sensor name to its registered
users.
Triggers
when ＞1cm
LED blinks once
Tamper Switch
The tamper switch (small black button underneath the back cover) will activate the
alarm if an unauthorized attempt is made to remove the contact from its installed
location.
Low Battery Indication
If the LED indicator ashes once per 3 seconds, the battery must be replaced.

5 6
Getting Started
Step One: Download the App
Download the app from the App Store or Google Play by searching the keywords
“Smart Life”.
Smart Life
Step Two: Register/ Log In
Press the "Register" button on the page and follow the instructions to create your
account rst.
Once you have an account, select the "Log in with Existing Account" to enter the
login page.

7
Step Three: Connect the Hub to Your Router
1.Tap “+” on the home page and then tap “Add Manually”. In the “Security & Sen-
sors” list, tap “Alarm (Wi-Fi)” under the “Alarm” category.
2.There are two ways to add the device: EZ mode (by default) and AP Mode.
EZ Mode: After powering on the device, if the indicator is blinking fast, tap “Conrm
indicator rapidly blink” to continue. Then, enter the WiFi password and tap “Conrm”
to complete the setup.