Let's Go Aero HCK345 User manual

REQUIRED TOOLS: 10 MM WRENCH, WIRE CRIMPING TOOL,
DRILL WITH PHILLIPS HEAD DRIVER, PHILLIPS SCREWDRIVER PARTS LIST
Attach lights [A, B] to brackets [C] as shown. Add two clips [H] to the drivers
side light bracket. These will be used later to attach your license plate.
LED LIGHT KIT FOR GEARCAGE PART #
HCK345
QTY. DESCRIPTION
A1 DRIVER SIDE LIGHT
B1 PASSENGER SIDE LIGHT
C2 BRACKET
D2 LOOM
E4 NUT
F4 LOCK WASHER
G6 WASHER
H2 PLATE MOUNT CLIP
J2 THUMB SCREW
K2 LOCK WASHER
L6 CONNECTOR
M4 SELF-TAP SCREW
N4 LARGE WASHER
1 WIRE (NOT SHOWN)
6 TIE WRAP (NOT SHOWN)
PAGE 1 OF 3
STEP 1 RECOMMENDED TOOL: 10 MM WRENCH
DETAIL 1
AB
D
E
F
G
H
J
K
M
N
C
H
E
F
G
C
C
BA
TIGHTEN NUTS SNUG.
DO NOT OVERTIGHTEN!
STEP 2 RECOMMENDED TOOLS: DRILL WITH PHILLIPS HEAD DRIVER, MARKER, PHILLIPS SCREWDRIVER
If you have installed or
will install an Aerfoil cover
congured to open to the
side as shown in DETAIL 2,
be sure to attach the light /
bracket assemblies at a
lower position as shown in
Detail 3.
IMPORTANT!
DETAIL 2
AERFOIL
GEARCAGE 1.5”
DETAIL 3
See next page
for specic
instructions
R
HCK345 1014 K0
L

PAGE 2 OF 3
STEP 2 RECOMMENDED TOOLS: DRILL WITH PHILLIPS DRIVER, MARKER, PHILLIPS SCREWDRIVER
Attach light / bracket assemblies to corners of GearCage
as shown in DETAIL 4 (or 1.5” down as shown in DETAIL
5 if you have a side opening Aerfoil, DETAIL 2). Mark hole
centers and drive self-tap screws [M] with washers [N] using
a drill and phillips bit. Use a center punch or drill a pilot hole
for easier driving of the screws. Stop short and tighten with a
screwdriver to avoid stripping out threads.
DETAIL 4
DETAIL 5
1.5”
M
N
M
N
M
N
STEP 3
RECOMMENDED TOOL: WIRE CRIMPERS
Run the wire under the GearCage, between cross tubes and panels. IMPORTANT: Yellow wire goes to the driver’s
side. Join wires of like colors with connectors [L] as shown in DETAILS 6-8 then cover with wire loom (DETAIL 9).
Secure the wires to the cross tubes with tie wraps (DETAIL 10). Attach your license plate (DETAIL 11).
VEHICLE
SIDE
DETAIL 6 DETAIL 7 DETAIL 8
DETAIL 9
DETAIL 10
J K G
DETAIL 11
(continued)
YELLOW
WIRE
LD
CRIMP
BOTH
ENDS.
HCK345 1014 K0

Copyright 2014, Lets Go Aero, Inc., All rights reserved.
ONE YEAR LIMITED WARRANTY
We warrant this Let’s Go Aero brand product during the time the original retail purchaser
owns it. This warranty terminates if a purchaser transfers the product to any other person.
Let’s Go Aero warrants this product to be free from defect in material and workmanship for
one year (retain your sales receipt for your records). Any product or part thereof found to be
defective within that period will be replaced without charge provided that: (1) the product was
not misused; (2) no alterations or modications were made; (3) its failure was not a result of
normal wear expected in the use of the product; (4) the product or part is delivered, freight
prepaid, to Let’s Go Aero.
Manufacturers only obligation shall be to replace such products or parts proved to be defec-
tive. A Return Merchandise Authorization is required prior to return. Please contact Let’s Go
Aero toll-free, at 877-464-2376 or 719-630-3800, or via email to [email protected] to
get an RMA number.
No warranty is given for LGA products purchased outside of the United States and Canada.
Technical Support
For assistance with this product, please contact us:
Let’s Go Aero, Inc.
2120 Naegele Road, Colorado Springs, CO 80904
USA
Phone:[phone] or 719-630-3800
Email: [email protected]
To learn more about our products and stay informed about useful options for transporting all
kinds of gear with your carrier, be sure to visit our website: www.LetsGoAero.com
PAGE 3 OF 3
HCK345 1014 K0