Circutor URBAN WB DC Series User manual

URBAN WB DC Series
INSTALLATION GUIDE
(M328A01-03-23A)

URBAN WB DC
2Installation Guide

URBAN WB DC
3Installation Guide
Disclaimer
Disclaimer
CIRCUTOR S.A.U. reserves the right to make modifications to the device or the unit specifications set
out in this instruction manual without prior notice.
CIRCUTOR S.A.U. on its web site, supplies its customers with the latest versions of the device speci-
fications and the most updated manuals.
www.circutor.com
Revision log
Date Revision Description
05/21 M328A01-03-21A Initial Version
09/21 M328A01-03-21B Device name change
11/21 M328A01-03-21C Changes in the following sections:
2.- 3.- 4.- 5.B.- 5.D.- 5.F.- 5.G.- 6.- 7.
02/22 M328A01-03-22A Changes in the following sections:
1.- 3.- 5.I.- 6.- 7.
04/23 M328A01-03-23A Changes in the following sections:
2.A.- 2.B.- 2.E.- 2.F.- 3.- 4.A.- 4.B.- 4.I.- 4.J.- 5.

URBAN WB DC
4Installation Guide
URBAN WB DC
Installation Guide
COPYRIGHT INFORMATION
This document is copyrighted, 2023 by CIRCUTOR S.A.U.. All rights are reserved. CIRCUTOR S.A.U.
reserves the right to make improvements to the products described in this manual at any time
without notice.
No part of this manual can be reproduced, copied, translated or transmitted in any form or by any
means without the prior written permission of the original manufacturer. Information provided in
this manual is intended to be accurate and reliable. However, the original manufacturer assumes no
responsibility for its use, or for any infringements upon the rights of third parties that may result
from its use.
All other product names or trademarks are properties of their respective owners.
CIRCUTOR reserves the right, in its discretion, to make any amendments, corrections or changes to this manual
and its contents at any time, without obligation to give prior notice.

URBAN WB DC
5Installation Guide
Contents
Disclaimer ......................................................................................................................................3
Revision log....................................................................................................................................3
Contents.........................................................................................................................................5
1.- So, hello! .............................................................................................................................................. 6
2.- Before the installation........................................................................................................................ 8
A.- Important Safety Instructions.............................................................................................. 8
B.- Electrical wiring considerations............................................................................................9
C.- Important Electrical Safety Instructions .............................................................................10
D.- EVSE Classification ...............................................................................................................11
E.- Storage................................................................................................................................. 12
F.-Unloading and handling ....................................................................................................... 13
3.- Dimensions and Overview.................................................................................................................14
A.- Dimensions .......................................................................................................................... 14
B.- Overview.............................................................................................................................. 16
4.- Installation..........................................................................................................................................18
A.- Minimum distances.............................................................................................................. 19
B.- Plates fixation ..................................................................................................................... 20
C.- Positioning............................................................................................................................ 21
D.- Opening................................................................................................................................22
E.- Device fixation......................................................................................................................23
F.- Connections ..........................................................................................................................24
G.- Wiring ...................................................................................................................................25
H.- Verification...........................................................................................................................26
5.-Technical Data .................................................................................................................................... 30
Need help?...................................................................................................................................33
Guarantee .....................................................................................................................................33

URBAN WB DC
6Installation Guide
This manual provides commissioning and use instructions information about URBAN WB DC, which
has been designed and tested to allow electric vehicle charging, specified in IEC 61851.
This document has different sections such as step-by-step installation procedure and technical data.
THE FOLLOWING SYMBOLS ARE USED FOR IMPORTANT
SAFETY INFORMATION IN THIS DOCUMENT
ELECTRICAL RISK
Take precautions to make the electrical connection inside the
device. Device must be disconnected from any power source during
commissioning.
ATTENTION!
Indicates that the damage to property can occur if appropiate
precautions are not taken.
1So, hello!

URBAN WB DC
7Installation Guide
• Compliant with IEC 61851; Electric vehicle conductive charging system (IEC 61851-
1 and IEC 61851-23).
• Compliant with IEC 62196; Plugs, sockets-outlets, vehicle connectors and vehicle
inlets- Conductive charging of electric vehicles (IEC 62196-1, IEC 62196-2 and IEC
62196-3).
• Directives: 2014/53/UE, Radio and Telecommunication Terminal equipment;
2014/30/UE, Electromagnetic Compatibility (EMC); 2014/35/UE, Low Voltage.
• Compliant with IEC 61851-24, Digital communication between a DC EV charging
station and an electric vehicle for control of DC charging. Meets the CCS
specification, DIN SPEC 70121. ISO 15118 ready.
• Compliant with RoHS 2011/65/EU-2017/2102, Restriction of Hazardous
Substances.
1So, hello!

URBAN WB DC
8Installation Guide
A Important Safety Instructions
Read carefully all the instructions before starting in order to
ensure properly installation of the Charge Point.
The Charge Point is designed for installation in indoor and outdoor areas. For each of the different
conditions of installation, the device must be installed safely and ensure adequate protection.
• Charge Point must not be installed in
areas where there is potential risk of
explosions or any salinity level.
• Comply strictly with electrical safety
regulations according to your
country.
• Charge point must not be installed in industrial
areas with high level of humidity or pollutants.
• Donot makerepairs ormanipulations
with the device energised.
• Do not install the Charge Point where
falling objects may damage the
equipment.
• Only trained and qualified personnel
should have access to electrical
parts inside the Charge Point.
• The surface where the Charge Point is
placed must withstand the mechanical
forces.
• Check the installation annually by
qualified technician.
• Do not use this device for anything other
than electric vehicle charging modes are
expected in IEC 61851.
• Remove from service any item that
has a fault that could be dangerous
for users (broken plugs, caps that
don’t close...).
• Do not modify this device. If modified,
CIRCUTOR will reject all responsibility
and the warranty will be void.
• Use only CIRCUTOR supplied spare
parts.
• Do not use this product if the
enclosure or the EV connector is
broken, cracked, open, or shows any
other indication of damage.
2Before the installation

URBAN WB DC
9Installation Guide
B Electrical wiring considerations
Take into consideration this section before start wiring con-
nections of the Charge Point.
1. ELECTRICAL PROTECTIONS
Charge Point may not include elements of electrical protection.
If this equipment has internal electrical protections, are installed in each socket-outlet for the
protection of the user against an electrical failure, according to the international standard IEC 61851-
1:2017.
In order to guarantee the total protection of the users and the installation (power supply line
included) in front of any electrical hazard, it is mandatory to install a main circuit breaker (MCB) and
a residual current device (RCD) upstream of the Charge Point.
These electrical protections and the rest of the installation have to be aligned with the local and
national rules. The selectivity of the protections has to be guaranteed at all times.
2. INPUT POWER SUPPLY
The input power supply line for the Charge Point must be hardwired from a dedicated power
transformer or generator and not by LV overhead power lines. It has to be done under electrical
safety regulations according to your country.
3. POWER SUPPLY LINE DIMENSIONING
The dimensioning of the input power supply line of the Charge Point must be checked by a qualified
electrician. Note that various factors such as cable length between distribution board and Charge
Point, maximum output current of the Charge Point may have influence of the selected cable.
In such cases, increasing the cable cross-section it is required to adapt the temperature resistance
of the power supply line.
2Before the installation

URBAN WB DC
10 Installation Guide
4. MAXIMUM OUTPUT POWER
Depending on the input power line, you can carry out the charging sessions to the electric vehicle
with different output power, it is possible to limit the maximum output power by software so as not
to exceed the available input power.
In order to implement this limitation by software, refer to the User Manual.
Note: In Chapter 4, you are going to find more electrical instructions so as to implement a secure
POWER SUPPLY LINE.
C Important Electrical Safety Instructions
Read carefully all the instructions before starting in order to
ensure properly handling of electrical parts.
A safe work environment is not enough to control all potential electrical hazards. It is recommended
to be very cautious and work safely. So, the safety rules shown below could help to control risks of
injury or death from workplace hazards.
• Avoid contact with energized electrical
circuits.
• Enclose all electric contacts and
conductors so that no one can
accidentally come into contact.
• Disconnect the power source before
servicing or repairing electrical
equipment.
• When it is necessary to handle
equipment that is plugged in, be sure
hands are dry and, when possible,
wear nonconductive gloves, protective
clothes and shoes with insulated soles.
• Use only tools and equipment with non-
conducting handles when working on
electrical devices.
• Never handle electrical equipment
when hands, feet, or body are wet or
perspiring, or when standing on a wet
floor.
• Never use metallic pencils or rulers, or
wear rings or metal watchbands when
working with electrical equipment.

URBAN WB DC
11Installation Guide
D EVSE Classification
Classification of the unit according to the IEC 61851-1:2017:
1 — Power supply Input • EV supply equipment connected to AC
supply network
• Permanently connected
2 — Power supply Output • DC EV supply equipment
3 — Environmental conditions • Indoor
4 — Access • Equipment for locations with restricted
access and;
• Equipment for locations with non-re-
stricted access.
5 — Mounting method • Stationary equipment
- Ground mounted; floor mounted
6 — Protection against electric shock • Class I
7 — Charging modes • Mode 4

URBAN WB DC
12 Installation Guide
E Storage
Whenever possible, the Charge point must be unloaded in their place of installation and operation.
In case of unloaded to a temporary location for storage, it is convenient to not remove the packaging
and store them meeting the following minimum requirements:
• Safety: Charge Point must be protected against negative elements such as heat radiation, direct
solar radiation, mechanical damage, organic dissolvent impacts, etc.
• Temperature: For temperatures below-20 ºC and over +60º C special attention must be paid to
the storage and handling.
• Environment: Charge Point must be stored in a dry and dust-free location. The distance from a
heat source must be 1 m away. Outdoor storage of the unit has to be avoided.
What’s included:
+Installation guide
Charge Point URBAN WB DC key
+ security key
Installation Guide CirCarLife RFID
Mifare Card
2x
1x
Cable roller plate Cable holder Wall plates Fixation screw
Note: Depending on the model, the elements in the package can vary.

URBAN WB DC
13Installation Guide
F Unloading and handling
All processes of unloading and handling of the Charge Point must be executed and monitored by
qualified personnel attending to the significant weight of the unit, complying with safety rules and
using the appropriate points of support.
Important notes:
• The delivery truck only unloads the pallet carrying the Charge Point.
• The delivery truck does not have the lifting facilities to move the Charge Point to its final location.
• The placement of the Charge Point to its final location is the responsibility of the contractor.
Once the Charge Point is already unloaded from the truck, move it to its final location with a forklift.

URBAN WB DC
14 Installation Guide
A Dimensions
Charge point, units specified in millimetres.
219
382
628
17
984
3Dimensions and Overview

URBAN WB DC
15Installation Guide
Wall plates:
82
17
240
3Dimensions and Overview

URBAN WB DC
16 Installation Guide
B Overview
1
2
3
5
7
4
5
2
8
6
Description
1Hat 5Wall support
2Key lock access 6Base
3Ventilation 7LED beacon light
4Cable output 8Power input

URBAN WB DC
17Installation Guide

URBAN WB DC
18 Installation Guide
What is needed:
2x
1x
Wall plates Fixation screw Cable roller plate
2x
8x 8x
Wall screws Anchors Cable holder
Screws and anchors are NOT INCLUDED.
It is highly recommended that the Charge Point would be installed in
brick or concrete wall.
Before the installation, a qualified installer must check that the wall is
in a perfect condition, and which screws and anchors are suitable for
that conditions.
4Installation

URBAN WB DC
19Installation Guide
A Minimum distances
When installing the device, some space shall be reserved for usability, maintenance and safety
reasons.
Please comply accordingly to your country specifications.
The next picture shows the minimum distances:
Measures in mm
Front view
500500
300
y(1)
(1) y distance shall be chosen according to your country rules.
4Installation

URBAN WB DC
20 Installation Guide
B Plates fixation
Install the plates on the wall considering the distances and the wall holes template shown on the
image below:
Measures in millimeters
Front view
y(2)
628
y(2)
Install the cable roller plate together with the cable holder ONLY on the wall next to the Charge Point,
as shown on the image.
(2) y distance shall be chosen according to your country rules.