Circutor URBAN M11 User manual

INSTRUCTION MANUAL
(M316B01-03-20A)
URBAN M11,T11, M12,T12

CIRCUTOR, SA reserves the right to make modifications to the device or the unit specifications set
out in this instruction manual without prior notice.
CIRCUTOR, SA on its web site, supplies its customers with the latest versions of the device specifi-
cations and the most updated manuals.
www.circutor.com
Disclaimer
Revision log
Date Revision Description
10/20 M316B01-03-20A Initial Version
2Instruction Manual
URBAN M11, T11, M12, T12

Here’s your
manual to use and
configure URBAN.
Disclainer ..................................................................................................................2
Revision log ..............................................................................................................2
Here’s your manual to use and configure URBAN.............................................3
1.-So, hello! ..............................................................................................................4
2.-Main features .....................................................................................................6
3.- How to use it? ...................................................................................................8
4.- LED beacon sequence ....................................................................................10
5.- Technical data ..................................................................................................12
Need help? .............................................................................................................15
Guarantee ...............................................................................................................15
03Instruction Manual
URBAN M11, T11, M12, T12

1
This manual provides commissioning information, which has been designed and
tested to allow electric vehicle charging, specified in IEC 61851.
This document has different sections describing electrical components inside
the charge station and a step-by-step installation procedure.
ELECTRIC RISK
Take precautions to make the electrical connection inside the unit.
Unit must be disconnected from any power source during
commissioning.
ATTENTION!
Indicates that the damage to property can occur if appropiate
precautions are not taken
THE FOLLOWING SYMBOLS ARE USED FOR IMPORTANT
SAFETY INFORMATION IN THIS DOCUMENTENT
• Complies with IEC 61851, Electric vehicle conductive charging
system (IES 61851-1 and IEC 61851-22)
• Complies with IEC 62196, Plugs, socket-outlets, vehicle couplers
and vehicle inlets (IEC 62196-1 and IEC 62196-2).
• Standards: 2014/35/UE, LVD;2014/30/UE, EMC.
04 Instruction Manual
URBAN M11, T11, M12, T12

So, hello!
The Charge Point may not include elements of electrical protection.
• Read all the instructions before
using and configurating this Charge
Point.
• Do not use this unit for anything
other than electric vehicle charging.
• Do not modify this unit. If
modified, CIRCUTOR will reject all
responsibility and the warranty will
be void.
• Comply strictly with electrical safety
regulations according to your
country.
• Do not make repairs or manipulations
with the unit energised.
• Only trained and qualified personnel
should have access to low-voltage
electrical parts inside the device.
• Check the installation annually by
qualified technician.
• Remove from service any item that
has a fault that could be dangerous
for users (broken plugs, caps that
don’t close...).
• Use only CIRCUTOR supplied spare
parts.
• Do not use this product if the
enclosure or the EV connector is
broken, cracked, open, or shows any
other indication of damage.
IMPORTANT SAFETY INSTRUCTIONS
Read carefully all the instructions before manipulat-
ing the charge point.
05Instruction Manual
URBAN M11, T11, M12, T12

2
1 — Hat
2 — LED Beacons
3 — Key lock access
4 — Base
1
4
2
3
06 Instruction Manual
URBAN M11, T11, M12, T12

Main features
Charge Point may not include elements of electrical protection.
• Plug ‘n’ Charge: Basic operation, start charging when vehicle is detected, no
need to authenticate.
• LED beacon: Three colour led indicates the status of the connectors.
• Vehicle charged: The user can easily differentiate when the vehicle is in
charging process or is fully charged.
07Instruction Manual
URBAN M11, T11, M12, T12

3
Standby
A
The unit has two LED beacons (one for each plug).
When it is green, it means that the unit is available
and ready to start a charge transaction (A status,
according to IEC 61851).
Start
B
To start a new charge transaction,
simply plug the cable.
Charging
C
When the charge transaction starts, the LED beacon shows a fix blue.
08 Instruction Manual
URBAN M11, T11, M12, T12

How to use it?
Charged
D
When the EV is fully charged, the LED beacon shows
a fix green.
Stop
E
Simply unplug the cable from the EV.
Once the cable is disconnected from the EV, the LED
status bar turns back to green (A status, according to
IEC 61851).
In this status, the unit is available to start a new charging transaction, whenever
it is required.
09Instruction Manual
URBAN M11, T11, M12, T12

4
Battery overheating
A
If overheating of the battery is detected, the unit stops charging and the LED
turns green. When the battery temperature becomes correct, the charger
recharges the vehicle and the LED turns blue.
10 Instruction Manual
URBAN M11, T11, M12, T12

LED beacon sequence
Errors
B
When the unit has an error, the LED bar shows a fix red.
11Instruction Manual
URBAN M11, T11, M12, T12

5
ELECTRICAL DATA
M11 M12 T11 T12
Power supply 1P+N+PE 3P+N+PE
Input voltage 230V~±10% 400V~±10%
Input Current (max) 35 A 67 A 35 A 67 A
Frequency 50Hz/60Hz
Number of sockets 12: Socket A,
Socket B 12: Socket A, Socket B
Maximum
socket Power 7.4 kW 7.4 kW (socket A & B) 22 kW 22 kW (socket A & B)
Maximum socket current 32 A 32 A
(socket A & B) 32 A 32 A (socket A & B)
Connectors type Type 2 Type 2
(socket A & B) Type 2 Type 2 (socket A & B)
Charging Mode Mode 3 Mode 3
(socket A & B) Mode 3 Mode 3 (socket A & B)
Overcurrent protection MCB 40A
(Curve C)
MCB 40A
(Curve C)
(socket A & B)
MCB 40A
(Curve C)
MCB 40A
(Curve C)
(socket A & B)
Safety RCD 30 mA (Type A)/ (Type B)(1)
Surge protection(1) Transient surge protector IEC 61643-1 (Class II)
GENERAL DATA
Light beacon RGB Colour indicator
ENVIRONMENTAL CONDITIONS
Operating temperature -5ºC ... +45ºC
Operating temperature with Low
temperature kit (1) -30ºC ... +45ºC
Storage temperature -20ºC ... +60ºC
Operating humidity 5% ... 95% Non-condensing
Enclosure rating IP54/IK10
Enclosure material Aluminium & ABS
12 Instruction Manual
URBAN M11, T11, M12, T12

Technical Data
MECHANICAL DATA
Enclosure door Frontal key locked door
Net weight 55Kg
Dimensions (W x H x D) 438 x 1264 x 288 mm
Min. cable section 25 mm2
STANDARDS
IEC 61851-1: 2010, IEC 61851-22: 2001, IEC 62196-1: 2014, IEC 62196-2: 2011, 2014/35/UE, LVD;2014/30/
UE
(1) Optional.
13Instruction Manual
URBAN M11, T11, M12, T12

14 Instruction Manual
URBAN M11, T11, M12, T12

Need help?
In case of any query in relation to unit operation or malfunction, please contact the CIRCUTOR, SA
Technical Support Service.
Technical Assistance Service
Vial Sant Jordi, s/n, 08232 - Viladecavalls (Barcelona)
Tel: [phone] (Spain)/[phone] (outside of Spain)
email: [e-mail]
Guarantee
CIRCUTOR guarantees its products against any manufacturing defect for two years after the delivery
of the units.
CIRCUTOR will repair or replace any defective factory product returned during the guarantee period.
•No returns will be accepted and no unit will be repaired or replaced if it is not
accompanied by a report indicating the defect detected or the reason for the return.
•The guarantee will be void if the units has been improperly used or the storage, in-
stallation and maintenance instructions listed in this manual have not been followed.
“Improper usage” is defined as any operating or storage condition contrary to the
national electrical code or that surpasses the limits indicated in the technical and
environmental features of this manual.
• CIRCUTOR accepts no liability due to the possible damage to the unit or other parts
of the installation, nor will it cover any possible sanctions derived from a possible
failure, improper installation or “improper usage” of the unit. Consequently, this guar-
antee does not apply to failures occurring in the following cases:
- Overvoltages and/or electrical disturbances in the supply;
- Water, if the product does not have the appropriate IP classification;
- Poor ventilation and/or excessive temperatures;
- Improper installation and/or lack of maintenance;
- Buyer repairs or modifications without the manufacturer’s authorisation.
15Instruction Manual
URBAN M11, T11, M12, T12

CIRCUTOR, SA.
Vial Sant Jordi, s/n
08232 - Viladecavalls (Barcelona)
Tel: [phone] - Fax: [phone]
www. circutor.com [e-mail]