Cisco CP-8865 User manual

CP-8865
Do Not Ship Enclosure with Phone Installed
[PHONE MUST BE INSTALLED ON-SITE]

- Due to the size and mass of this product, it is
Take into consideration before you install:
important that the Backbox is safely installed
according to these installation instructions.
- Make sure that the type of wall is capable of supporting
the system and use screws that are suitable for that type of wall.
accordance with state and local building regulations.
CP-8865 Mounting the Enclosure

Accessory Kits
Drilled Spanner
Coverplate
Mounting
Screw
#6-32 x 3/16”
Button Head Torx
(Spare)
Machine Screw
T-15 Pin Torx
Security Driver Bit
#8 Hex Nut
(Ground Lug)
Jumper Shunt
#6-32 x 5/8” Flat Head
Pin Torx Machine Screw
(Spare - 2 Pieces)
Machine Screw
Torx Security Bit &
#00 Screw Driver Kit
Keypad Cover Accessory Kit
Keypad
Driver Bit
Spare Screw Kit
+ 1 Spare
M3x0.5Pitch Machine Screw
Phone Mounting Screw Kit
Hookswitch Coverplate
T-15 Driver Bit Kit (on the Outside by the Hookswitch)
3/16”
Hex L-Key

Tools Required:
1) Electric Powered Hand Drill
2) Drill Bit (Use Correct Drill Bit for Wood / Concrete)
Mount the Backbox Assembly
to the Wall
A) Prepare Hole on Drywall (with Stud Behind) / Concrete
B) Insert Stud Anchors in to Holes
C) Align then Place Backbox Assembly Mounting Holes to Studs Anchors
Steps
Figure Shown Typical Installation:
3) Leveler
4) Torque Wrench, Wrench and Socket
D) Tighten Washers and Nuts that included with Stud Anchors
E) Torque to Stud Anchors Manufacturer's Recommended ft./lbs.

Remove Both
USB & KEM
Covers
Then Connect Power Plug (1) &
Network Cable (2), etc. Through
Mounting Bracket
Remove Handset &
Disconnect Cord from Phone.
(2)
(1)
(3)

This Will Allow Camera to Line Up with
Camera Hole on the Faceplate
Screw
Mounting
Phone
Mount
Cable
Exit
Cables Run Through Cable Exit then
Connect to Phone
Mounting
Holes
the USB Port on the Side
Right Angle USB-A to
Then Tightening Screws
Lower Phone Mount Until Tabs Stops
Tab
Tab
the USB to Analog Audio Module (UAAM)
USB-B to
Screw
Mounting
from Serial
Controller
Network Cable
AUX
Update Note: 1) Serial Controller RJ11 to AUX
Date: 02/07/2019

Red Wire to J4 (Position 1)
Green Wire to J4 (Position 3)
Black Wire to J4 (Position 4)
Yellow Wire to J4 (Position 2)
J4
Armored Cord Handset to
USB to Analog Audio Module
1) #00 size Phillips Screw Driver
Tool Provided for Terminal Block Screw:
Armored Cord Handset Wires End
1
2
3
4
6
7
5
8
9
10
RED Wire
YELLOW Wire
GREEN Wire
BLACK Wire
Handset
Serial Controller Connections (6,7 & 8)
To Phone
Install Shunt on JP2
to Enable [Auto Answer Mode]
USB-A
USB-B to
RED Wire
BLACK Wire
921285C
GREEN Wire
RED Wire
BLACK Wire
6
7
8
9
5
Hookswitch Connections
Connections
*
*
J1

Ground Lug
Hex Nut
Not Provided
Assembly
Ground the Backbox from ESD
Ground Wire &
UAAM Not Shown
*Handset Wires to
*
*
Network Cable are
Network Cable
Serial
Controller
Backbox
UAAM

Open Camera Shutter
Before Installing the Faceplate Assembly
<< Factory Disconnected >>
Reconnect Before Installing the Faceplates Assemblies
*First Install the Upper Faceplate Assembly
then the Lower Faceplate Assembly
Use Provided Driver Bit
to Install Security Screws
Tool Required:
Powered Screw Driver or Powered Hand Drill
Also Double Check all Cables and Wires are Plugged in and Secure
Connection Label
with Diagram
UAAM

Ground Wires Twist
Nut
Ground Faceplate from ESD
Lip Go Under
Diagram Shown Typical Installation
Upper Faceplate Assembly