Claypaky C61401 User manual

1
A.LEDA WASH K5
A.LEDA WASH K10
A.LEDA WASH K20
C61401
C61405
C61410
®
I STRUCTIO MA UAL
Congra ula ions on choosing a Clay Paky produc !
We hank you for your cus om.
Please no e ha his produc , as all he o hers in he rich Clay
Paky range, has been designed and made wi h o al quali y o
ensure excellen performance and bes mee your expec a ions
and requiremen s.
Carefully read this instruction manual in its entirety and keep it
safe for future reference. It is essential to know the information
and comply with the instructions given in this manual to ensure
the fitting is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting
or to other property or persons deriving from installation, use and
maintenance that have not been carried out in conformity with this
instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the
characteristics stated in this instruction manual at any time and
without prior notice.
E GLISH
PRELIMI ARY
I DEX
Page
2
3
4
5
7
14
16
19
19
20
Contents
Safety information
Unpacking and preparation
Installation and start-up
Control panel
Menu setting
Maintenance
Optional accessories
Technical information
Cause and solution of problems
Channel functions

2
A.LEDA WASH
• Installation
Make sure all parts for fixing the projector are in a good state of repair.
Make sure the point of anchorage is stable before positioning the projector.
The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if
the primary support system fails, the fitting falls as little as possible.
If the safety chain gets used, it needs to be replaced with a genuine spare.
• Minimum distance of illuminated objects
The projector needs to be positioned so that the objects hit by the beam of light are at least 0.20
metres (8”) from the lens of the projector.
• Minimum distance from flammable materials
The projector must be positioned so that any flammable materials are at least 0.20 metres (8”) from
every point on the surface of the fitting.
• Mounting surfaces
It is permissible to mount the fitting on normally flammable surfaces.
• Maximum ambient temperature
Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).
• IP20 protection rating
The fitting is protected against penetration by solid bodies of over 12mm (0.47”) in diameter (first
digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0).
• Protection against electrical shock
Connection must be made to a power supply system fitted with efficient earthing (Class I appliance
according to standard EN 60598-1).
It is, moreover, recommended to protect the supply lines of the projectors from indirect contact
and/or shorting to earth by using appropriately sized residual current devices.
• Connection to mains supply
Connection to the electricity mains must be carried out by a qualified electrical installer.
Check that the mains frequency and voltage correspond to those for which the projector is designed
as given on the electrical data label.
This label also gives the input power to which you need to refer to evaluate the maximum number
of fittings to connect to the electricity line, in order to avoid overloading.
• Temperature of the external surface
The maximum temperature that can be reached on the external surface of the fitting, in a thermally
steady state, is 90°C (194°F).
• Maintenance
Before starting any maintenance work or cleaning the projector, cut off power from the mains
supply.
• Battery
This product contains a rechargeable lead-acid battery. To preserve the environment, please
dispose the battery at the end of its life according to the regulation in force. Instructions on how to
remove the battery from the product are available on www.claypaky.it
SAFETY I FORMATIO
The products referred to in this manual conform to the European Community Directives to which
they are subject:
•Low Voltage 2006/95/CE
•Electromagnetic Compatibility 2004/108/CE
0.2
LED
IP20
tc90°C
LiFePO4

3
A.LEDA WASH
U PACKI G A D PREPARATIO
099117
2 x 183102/802
1
90°
90°
90°
90°
LOCKED
UNLOCKED
PA Mechanism Lock and Release (every 90°) - Fig. 2
2
Packing contents - Fig. 1

4
A.LEDA WASH
3
1
2
3
2
1
4
I STALLATIO A D START-UP
Connecting and disconnecting power cable - Fig. 4
Installing the projector - Fig. 3
The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.
WAR I G: with the exception of when the projector is positione on the floor, the safety cable must be fitte . (Co . 105041/003 available on request).
This must be securely fixe to the support structure of the projector an then connecte to the fixing point at the centre of the base.

5
A.LEDA WASH
Switching on the projector - Fig. 7
Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:
Model Firmware xxx (Fixture ID) System errors
A.leda Wash Version X.X.X Dmx Address xxx E: .........................
Date - Hour W: .........................
On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the “ ome” position (Pan 50% - Tilt 50%). The control panel
(Fig. 7) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions:
rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set).
During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the
F
key will be cancelled.
CO TROL PA EL
7.5m
1
2
Dmx Address
Warning Message
Fixture ID
7
Con inue ➔
Connecting to the control signal line (DMX) - Fig. 6
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female
connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTA T: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the
shield braid and to pin 1 of the connectors.
DMX 512
Mains
5
6
SIGNAL
SCREEN
DMX 512
5 PIN
1
2
3
4
5
SIGNAL
SCREEN
1
3
2
DMX 512
3 PIN
SIGNAL
SIGNAL
Connecting to the mains supply - Fig. 5
B: connecting one “A.leda
Wash K5” to the mains, it is
possible to connect up to a
maximum of 11 “A.leda Wash
K5” in parallel at the same time.

6
A.LEDA WASH
28
28
Reversal of the display - Fig. 8
To activate this function, press UP
B
and DOWN
C
keys simultaneously while the display is in the rest mode. This status will be memorised and
maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
The address can also be set with the projector switched off.
Setting the address: see pag. 8.
Setting the projector Fixture ID
On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255).
The Fixture ID address can be set with the projector switched off.
Setting the Fixture ID: see pag. 8.
8
Functions of the buttons - Using the menu
Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press
F
to momentarily activate the display and thus access the settings. Once the required operations have been carried out,
the display will switch off again after a wait time of 30 seconds.
USI G THE ME U:
1) Press
F
once – “Main Menu” appears on the display.
2) Use the UP
B
and DOWN
C
keys to select the menu to be used:
• Setup (Setup Menu): To set the setting options.
• Option (Option Menu): To set the operating options
• Informations (Informations Menu): To read the counters, software version and other information.
• Manual Control (Manual control Menu): To trigger the test and manual control functions.
• Test (Test Menu): To check the proper functionning of effects
• Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel.
To enable the "Advanced" see pag.13
3) Press
F
to display the first item in the selected menu.
4) Use the UP
B
and DOWN
C
keys to select the MENU items.
Confirms the displayed value, or activates the displayed function, or enters the successive
menu.
Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.
Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.
Return to the top level.
Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù.
F
C
DOWN
B
UP
D
LEFT
E
RIG T

7
A.LEDA WASH
System
Errors
Information
Fixture
ours
4
Reset
Manual
Control
Channel
6
ME U SETTI G
3
System
Version
Board
Diagnost.
Dmx
Monitor
Fans
Monitor
Access code
1234
Advanced
Calibration
Upload
Firmware
Setup
Model
Con inue ➔
Set Up
Option
Information
Manual
Control
Test
Advanced
1
5
Pan / Tilt
Colour
All
Test
Dmx
Address
Channel
Mode
Ethernet
Interface
Fixture ID
Network
params
2
Pan / Tilt
Silent
Mode
Display
Option Invert
Pan
Invert
Tilt
Swap
Pan-Tilt
Encoder
Pan-Tilt
Standard
Setting Default
Preset
User
Preset 1
User
Preset 2
User
Preset 3
Quiet

8
A.LEDA WASH
DMX ADDRESS
OTE: without the DMX signal the Address (XXX) flashing
Allows you to select the DMX ADDRESS.
1) Press
F
- the current DMX Adress appear on the display.
2) Use the UP
B
and DOWN
C
, RIG T
E
keys to plan the DMX
Address.
3) Press
F
to confirm the selection or LEFT
D
to keep current settings.
CHA EL MODE
Allows you to select a channel arrangement from the two available.
1) Press
F
- the current settings appear on the display (Standard or
Vector).
2) Use the UP
B
and DOWN
C
keys to select one of the following
settings:
- Standard
- Shape
- Extended
3) Press
F
to confirm the selection or LEFT
D
to keep current settings.
FIXTURE ID
Allows you to select the FIXTURE ID.
1) Press
F
- the current Fixture ID appear on the display.
2) Use the UP
B
, DOWN
C
, RIG T
E
keys to plan the Fixture ID.
3) Press
F
to confirm the selection or LEFT
D
to keep current settings.
ETHER ET I TERFACE
It lets you set the Ethernet settings to be attributed to the projector.
1) Premere
F
.
2) Use the UP
B
and DOWN
C
keys to select the “Ethernet Interface”
options to set:
Control Protocol
It lets you select the “Control Protocol” Art-net to assign according to the
control unit used:
1) Press
F
the current setting appears on the display.
2) Use the UP
B
and DOWN
C
keys to select one of the following settings:
- Disabled
- Art-net on IP 2
- Art-net on IP 10
3) Press
F
to confirm the selection or LEFT
D
to keep the current setting.
Repeat on DMX
It lets you enable the transmission of the Ethernet protocol by DMX signal
to all the connected projectors.
1) Press
F
the current setting appears on the display.
2) Use the UP
B
and DOWN
C
keys to select one of the following settings:
- Disabled: DMX transmission disabled.
- Enabled on primary: DMX transmission enabled.
3) Press
F
to confirm the selection or LEFT
D
to keep the current setting.
Universe
It lets you assign the “Universe” number to be assigned to a series of
projectors.
1) Press
F
– the current Universe address appears on the display.
2) Use the UP
B
, DOWN
C
, RIG T
E
keys to set the Universe
address.
3) Press
F
to confirm the selection or LEFT
D
to keep the current
setting.
SET UP ME U
Set Up Dmx
Address
Channel
Mode
Fixture ID
Address xxx
Standard
Shape
Extended
Value xxx
Ethernet
Interface
Control
Protocol
Repeat on
DMX
Universe
OTE: On grey the default options

9
A.LEDA WASH
Con inue ➔
PA / TILT
Invert pan
Used for reversing Pan movement.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B
and DOWN
C
keys to enable (On) or disable (Off)
PAN inversion.
3) Press
F
to confirm the selection or LEFT
D
to keep current
settings.
Invert tilt
Used for reversing tilt movement.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B
and DOWN
C
keys to enable (On) or disable (Off)
Tilt inversion.
3) Press
F
to confirm the selection or LEFT
D
to keep current
settings.
Swap Pan-Tilt
Used for swapping Pan and Tilt channels (as well as Pan fine and Tilt fine).
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B
and DOWN
C
keys to enable (On) or disable (Off)
Pan and Tilt channel swap.
3) Press
F
to confirm the selection or LEFT
D
to keep current
settings.
Encoder Pan-Tilt
Used for enabling the Pan / Tilt encoders.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B
and DOWN
C
keys to enable (On) or disable (Off)
Pan / Tilt encoders.
3) Press
F
to confirm the selection or LEFT
D
to keep current
settings.
SILE T MODE
It lets you select the “Silent Mode” from the two available.
1) Press
F
the current setting appears on the display.
2)
Use the UP Band DOWN Ckeys to select one of the following
settings:
Standard: Maximum speed and consequently maximum effects noise
level.
Quiet: reduces the speed of some effects, thereby reducing their noise
level.
3) Press
F
to confirm the selection or LEFT
D
to keep the current
setting.
DISPLAY
Used for automatically reduce brightness on the display after about 30
seconds in idle.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B
and DOWN
C
keys to enable (On) or disable
(Off) the decreasing of display brightness.
3) Press
F
to confirm the selection or LEFT
D
to keep current
settings.
OPTIO S ME U
Swap
Pan-Tilt
On
Off
Encoder
Pan-Tilt
On
Off
Pan / Tilt
Option Invert
Pan
On
Off
Invert
Tilt
On
Off
Silent
mode Standard
Quiet
On
Off
Display

10
A.LEDA WASH
SETTI G
Used to save 3 different settings of the items in the options menu and
relative submenus.
1) Press
F
- “Default preset” appears on the display.
2) Use the UP
B
and DOWN
C
keys to select one of the following
configurations:
- Default preset (*)
- User preset 1
- User preset 2
- User Preset 3
3) Press
F
- “Load preset X” appears on the display.
4) Use the UP
B
and DOWN
C
keys to select:
- Load preset X to recall a previously stored configuration.
- Save to preset X to store the current configuration.
a confirmation message (Are you sure?) appears on the display.
5) Select YES to confirm the selection or NO to keep the current setting
and return to the next higher level.
(*) DEFAULT PRESET
Used for restoring default values on all options menu items and relevant
submenus.
1) Press
F
, a confirmation message (Are you sure?) appears on the
display.
2) Select YES to confirm the selction or NO to keep current setting.
OPTION DEFAULT
Invert Pan Off
Invert Tilt Off
Swap Pan-Tilt Off
Encoder Pan-Tilt On
Display On
SYSTEM ERRORS
Shows a list of warnings and messages relevant to errors occurred since
the fixtures switching-on.
1) Pressing
F
you are allowed to reset the SYSTEM ERRORS list.
A confirmation message (Are you sure you want to clear error list ?)
appears on the display.
2) Select YES to reset the list or NO to go back.
FIXTURE HOURS
Used for displaying projector operating hours (total and partial).
1) Press
F
- ours total and partial appears on the display.
Total counter
Counts the number of projector working life hours (from manufacture to date).
Partial counter
Counts the number of partial projector working life hours since the last
reset to date.
2) Press
F
to reset partial projector working hours a confirmation
message (Are you sure?) appears on the display.
3) Select YES to reset partial projectors counter or NO to keep the current
setting and return to the top menu level.
SYSTEM VERSIO
Used for displaying the software and hardware version of each board
installed in the projector.
CPU brd (CPU board)
0: PT-3f (Scheda Pan / Tilt)
1: Ld - Kxx (Scheda LED)
I FORMATIO ME U
Save To
Preset 3
Reset To
Dafault
Go Back
Setting Default
Preset
Load
Preset 1
Save To
Preset 1
User
Preset 1
Load
Preset 2
Save To
Preset 2
User
Preset 2
Load
Preset 3
User
Preset 3
Information System
Errors
Fixture
ours
Total XXX
Partial XXX
Reset...
System
Version
Board Revis. w.rv.
CPU brd x.x.x x.x
com.dev x.x
0: PT-3f x.x x.x
1: Ld - Kxx x.x x.x

11
A.LEDA WASH
Con inue ➔
BOARD DIAG OSTIC
Used for displaying the status error of each board installed in the projector:
0: PT-3f (Scheda Pan / Tilt)
1: Ld - Kxx (Scheda LED)
DMX MO ITOR
Used for displaying the projector DMX channel level in bit (Val) and in
percentage (Perc).
FA S MO ITOR
Used for displaying the speed of each fan installed in the projector:
PwrSp (fan PSU)
ead (fan head)
ETWORK PARAMS
Allows the "Network" parameters of the projector to be displayed or:
IP address: Internet Protocol address (two projectors must not have
the same IP address)
IP mask: 255.0.0.0
Mac address: Media Access Control: the projector’s Ethernet Address
RESET
Used for resetting the projector.
1) Press
F
to reset the projectors, a confirmation message (Are you
sure ?) appears on the display.
2) Select YES to starting reset the fixture or NO to keep the current
setting and return to the top menu level.
CHA EL
Used for setting channel levels from the projector control panel.
1) Press
F
- the first channel appears on the display.
2) Use the UP
B
and DOWN
C
keys to select the required channel:
3) Press
F
and use the UP
B
and DOWN
C
keys to select the
required DMX level (value between 0 and 255).
4) Press LEFT
D
to return to the top menu level.
TEST
Allows you to check the proper functioning of effects.
1) Press
F
to return to the top menu level.
2) Use the UP
B
and DOWN
C
keys to select the required test.
3) Press
F
to confirm the selection or LEFT
D
to keep current set-
tings.
Test sequence:
Pan - Tilt effects (Pan & Tilt)
Colour effects (CMY / CTO / Colour wheel)
All effects
Network
params
Dmx
Monitor
Board Status Err%
0:PT-3f Good 0.00
1: Ld - Kxx Good 0.00
Fans
Monitor
Fan Speed (RPM)
PwrSp XXXX
ead XXXX
MA UAL CO TROL
Manual
Control
No
Yes
Reset
Channel
TEST ME U
Test
Pan-Tilt
Colour
All
Board
Diagnost.

12
A.LEDA WASH
Advanced
Code
1234
Calibration
Upload
Firmware
Transfer the firmware on all
the connected fixtures ?
Are you sure ?
Yes/No
Setup
Model
Changing to a wrong model
may damage the fixture.
Are you sure ?
Yes/No
To enable the "Advanced Menu" set up the "Access code" (1234) using the
UP
B
, DOWN
C
, RIG T
E
keys.
Press
F
- "Menu advanced" appears on the display
UP LOAD FIRMWARE
Allows you to transfer the firmware from 1 fixture to all the connected fixtures.
1) Press
F
, a confirmation message appears on the display.
2) Select YES to start the firmware loading or NO to keep the current set-
ting and return to the top menu level
SETUP MODEL
Allows you to change the default model of projector.
1) Press
F
a confirmation message appears on the display.
2) Select YES to define the model of projector or NO to keep the current
setting and return to the top menu level.
CALIBRATIO
Allows you to adjust effects from the control panel to obtain perfect unifor-
mity between the projectors.
1) Press
F
- “channels” appears on the display.
2) Using the UP
B
and DOWN
C
keys, select the effect you wish to
regulate.
3) Press
F
and use the RIG T
E
, UP
B
and DOWN
C
buttons to
make the adjustment by setting a value between 0 and 255.
4) Press
F
to confirm the selection or LEFT
D
to keep current set-
tings and return to the top level.
FACTORY DEFAULT
Allows you to restore default values of all channels (128).
1) Press
F
– a confirmation message appears on the display (Reset
calibration to factory default ?).
2) Select YES to reset calibration to factory default or NO to keep the
current setting and return to the top menu level.
ADVA CED ME U

13
A.LEDA WASH
5
6
3
4
1
2
9
Battery removal - Fig. 9
This product contains a rechargeable lead-acid battery. To preserve the environment, please dispose the battery at the end of its life according
to the regulation in force.
LiFePO4

14
A.LEDA WASH
1
2
3
4
1
3
2
4
10
11
Opening the covers - Fig. 10
Removing/Assembling the lens unit - Fig. 11
B: Apply Loctite 222 (p/n COL002) to the threads of the 3 screws (1) before tightening them. A torque of 0.3N is recommended in order to avoid
damaging the zoom movement actuators.
MAI TE A CE

15
A.LEDA WASH
2
1
DIM002/001
12
Replacing the line actuator - Fig. 12
B: It is highly recommended to use the DIM002/001 (1) template whenever it is necessary to replace one of the three Zoom movement line actuators.
DIM002/001 ensures the actuator group is centred correctly on the lens plate before tightening the 2 screws (2) that fasten the actuator in place.

16
A.LEDA WASH
1
2
3
275216-002275216-001
4
092037/002
1
2
3
OPTIO AL ACCESSORIES
13
14
A.LEDA WASH K5
Transparent mask - Fig. 14
Cover - Fig. 13
275216/001 - Transparent cover
275216/002 - Frosted cover

17
A.LEDA WASH
1
2
3
270216-002270216-001
1
3
4
2
270201-802
A.LEDA WASH K10
Cover - Fig. 15
270216/001 - Transparent cover
270216/002 - Frosted cover
Transparent mask - Fig. 16
15
16
Con inue ➔

18
A.LEDA WASH
2
3
2
274216-002274216-001
1
3
4
1
274201-802
A.LEDA WASH K20
Cover - Fig. 17
275216/001 - Transparent cove
275216/002 - Frosted cover
Transparent mask - Fig. 18
17
18

19
A.LEDA WASH
CAUSE AND SOLUTION OF PROBLEMS
THE PROJECTOR WILL OT SWITCH O
PROBLEMS
ELECTRO ICS O -OPERATIO AL
DEFECTIVE PROJECTIO
REDUCED LUMI OSITY
POSSIBLE CAUSES CHECKS AND REMEDIES
o mains supply.
LED exhausted or defective.
Signal transmission cable faulty or disconnected.
Incorrect addressing.
Fault in the electronic circuits.
Lenses or reflector broken
Dust or grease deposited.
Check the power supply voltage.
Replace the LED. (See instructions).
Replace the cables.
Check addresses (see instructions).
Call an authorised technician.
Call an authorised technician.
Clean (see instructions).
358
(14.09")
253
(9.96")
423
(16.65")
250
(9.84")
360
(14.17")
381
(15.00")
155
(6.10")
220
(8.66")
320
(12.60")
253
(9.96")
374
(14.72")
245
(9.65")
155
(6.10")
584
(22.99")
160
(6.30")
380
(14.96")
395
(15.55")
330
(12.99")
476
(18.74")
360
(14.17")
460
(18.11")
479
(18.86")
160
(6.30")
290
(11.42")
TECHNICAL INFORMATION
P wer supplies available
100-240V 50/60Hz
Input p wer
• K20 - 750VA
• K10 - 450VA
• K5 - 170VA
Max 1800VA (with 11 A.leda Wash K5 connected in parallel)
Lamp
LED Osram Ostar RGBW - 15W
M t rs
5 (k10 & k20), 2 (k5) stepper motors, operating with microste-
ps, totally microprocessor controlled.
C ling
• High efficiency die-cast aluminium
• Forced ventilation
Inputs
DMX 512
W rking p siti n
Functioning in any position.
M vable b dy
• Movement by means of two stepper motors, controlled by
microprocessor.
• Automatic repositioning of PA and TILT after accidental
movement not controlled by control unit.
• Travel:
- PA = 540°
- TILT = 270°
IP20 pr tecti n rating
• Protected against the entry of solid bodies larger than 12mm
(0.47”).
• o protection against the entry of liquids.
CE Marking
In conformity with the European Union Low Voltage Directive
2006/95/CE and Electromagnetic compatibility Directive
2004/108/CE.
Weights
• K5: 7.55kg
• K10: 14.10 kg
• K20: 19.30 kg

20
A.LEDA WASH
A.LEDA WASH K5
CHA EL FU CTIO
CHA -
EL
STA DARD EXTE DED
CHA EL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
CHA -
EL
SHAPES
CHA EL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
Reserved to special shape functions
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
CHA -
EL
CHA EL MODE
Red
Red fine
Green
Green fine
Blue
Blue fine
White
White fine
CTO
Macro colour
Strobe
Dimmer
Dimmer Fine
Pan
Pan Fine
Tilt
Tilt Fine
Function
Reset
RED LED 1 (If RED "channel 1" to 0)
GREEN LED 1 (If GREEN "channel 2" to 0)
BLUE LED 1 (If BLUE "channel 3" to 0)
RED LED 2 (If RED "channel 1" to 0)
GREEN LED 2 (If GREEN "channel 2" to 0)
BLUE LED 2 (If BLUE "channel 3" to 0)
RED LED 3 (If RED "channel 1" to 0)
GREEN LED 3 (If GREEN "channel 2" to 0)
BLUE LED 3 (If BLUE "channel 3" to 0)
RED LED 4 (If RED "channel 1" to 0)
GREEN LED 4 (If GREEN "channel 2" to 0)
BLUE LED 4 (If BLUE "channel 3" to 0)
RED LED 5 (If RED "channel 1" to 0)
GREEN LED 5 (If GREEN "channel 2" to 0)
BLUE LED 5 (If BLUE "channel 3" to 0)
RED LED 6 (If RED "channel 1" to 0)
GREEN LED 6 (If GREEN "channel 2" to 0)
BLUE LED 6 (If BLUE "channel 3" to 0)
RED LED 7 (If RED "channel 1" to 0)
GREEN LED 7 (If GREEN "channel 2" to 0)
BLUE LED 7 (If BLUE "channel 3" to 0)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40