Code Code Reader 1400 User manual

C006819_03_CR1400_User_Manual

C006819_03_CR1400_UserManual

User Manual

Code Reader™ 1400

Manual Version 03

Release Date: June 2012

C006819_03_CR1400_User_Manual

Statement of Agency Compliance

Code voids product warranty if the hard case has been opened or tampered with in any way.

In addion, a CB Test Cercate has been issued by the Naonal Cercaon Board (NCB) indicang CR1400

meets all safety and quality standards in accordance to IEC 60950-1:2001, First Edion.

The Code Reader™ 1400 (CR1400) has been tested for compliance with FCC regulaons and was found to be

compliant with all applicable FCC Rules and Regulaons.

IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, this device must not be co-

located or operate in conjuncon with any other antenna or transmier.

CAUTION: Changes or modicaons not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

The CR1400 has been tested for compliance to CE standards and guidelines and was found to conform to

applicable CE standards, specically the EMC requirements EN 55024, ESD EN 61000-4-2, Radiated RF Immunity

EN 61000-4-3, ENV 50204, EFT EN 61000-4-4, Conducted RF Immunity EN 61000-4-6, EN 55022, Class B Radiated

Emissions, and Class B Conducted Emissions.

C006819_03_CR1400_User_Manual

Code Reader™ 1400 User Manual

The soware described in this manual may only be used in accordance with the terms of its license agreement.

No part of this publicaon may be reproduced in any form or by any means without wrien permission from Code Corporaon. This

includes electronic or mechanical means such as photocopying or recording in informaon storage and retrieval systems.

NO WARRANTY. This technical documentaon is provided AS-IS. Further, the documentaon does not represent a commitment

on the part of Code Corporaon. Code Corporaon does not warrant that it is accurate, complete or error free. Any use of the

technical documentaon is at the risk of the user. Code Corporaon reserves the right to make changes in specicaons and

other informaon contained in this document without prior noce, and the reader should in all cases consult Code Corporaon

to determine whether any such changes have been made. Code Corporaon shall not be liable for technical or editorial errors or

omissions contained herein; nor for incidental or consequenal damages resulng from the furnishing, performance, or use of this

material. Code Corporaon does not assume any product liability arising out of or in connecon with the applicaon or use of any

product or applicaon described herein.

NO LICENSE. No license is granted, either by implicaon, estoppel, or otherwise under any intellectual property rights of Code

Corporaon. Any use of hardware, soware and/or technology of Code Corporaon is governed by its own agreement.

The following are trademarks or registered trademarks of Code Corporaon:

CodeXML®, Maker, QuickMaker, CodeXML® Maker, CodeXML® Maker Pro, CodeXML® Router, CodeXML® Client SDK, CodeXML®

Filter, HyperPage, CodeTrack, GoCard, GoWeb, ShortCode, GoCode®, Code Router, QuickConnect Codes, Rule Runner®, Cortex®,

CortexRM, CortexMobile, Code, Code Reader, CortexAG, CortexStudio, CortexTools, Anity®, and CortexDecoder.

All other product names menoned in this manual may be trademarks of their respecve companies and are hereby acknowledged.

The soware and/or products of Code Corporaon include invenons that are patented or that are the subject of patents pending.

U.S. Patents: 6997387, 6957769, 7428981, 6619547, 6736320, 7392933, 7014113, 7240831, 7353999, 7519239, 7204417, 6942152,

7070091, 7097099, 7621453, 8001550, 8011584

The Code Reader soware uses the Mozilla SpiderMonkey JavaScript engine, which is distributed under the terms of the Mozilla

Public License Version 1.1.

The Code Reader soware is based in part on the work of the Independent JPEG Group.

Code Corporaon, 14870 South Pony Express Road, Suite 200, Bludale, UT 84065

www.codecorp.com

C006819_03_CR1400_User_Manual

Table of Contents

1.0 - Unpacking............................................................................................................................................................... 1

2.0 - Aaching/Detaching a Cable................................................................................................................................... 1

3.0 - Powering the Reader On/O................................................................................................................................... 1

4.0 - Using a CR1400 Out of a Stand................................................................................................................................ 2

5.0 - Using a CR1400 in a Stand....................................................................................................................................... 2

6.0 - Reading Range ........................................................................................................................................................ 3

7.0 - Reader Feedback .................................................................................................................................................... 3

8.0 - Symbologies Defaulted On...................................................................................................................................... 4

9.0 - Symbologies Defaulted O...................................................................................................................................... 4

10.0 - Locang the Hardware Revision Number .............................................................................................................. 4

11.0 - Reader ID & Firmware Version .............................................................................................................................. 5

12.0 - CR1400 Overall Dimensions .................................................................................................................................. 6

13.0 - USB Cable Example with Pinouts........................................................................................................................... 7

14.0 - RS232 Cable Example with Pinouts ....................................................................................................................... 7

15.0 - Reader Pinouts ..................................................................................................................................................... 8

16.0 - Maintenance.........................................................................................................................................................8

17.0 - Warranty .............................................................................................................................................................. 9

C006819_03_CR1400_User_Manual

2.0 - Aaching and Detaching a Cable

1.0 - Unpacking

Remove the CR1400 from its packing and inspect it for damage. If the reader was damaged during shipping, please call Code at

(801) 495-2200.

Depending on the kit ordered, a USB or RS232 Anity® cable has been included with your reader.

USB Anity® Cable RS232 Anity® Cable

w/ Power Supply

For USB Cable: plug the USB end of the Anity® cable into a USB port on the host device. Aer several seconds, the reader will beep

twice, the reader will vibrate, and the LED will turn o to indicate the CR1400 is ready for use.

For RS232 Cable: plug the power supply into the AC outlet, plug the power supply cord into the barrel jack of the cable, and connect

the RS232 connector to the appropriate serial port on the host device. Aer several seconds, the reader will beep twice, the reader

will vibrate and the LED will turn o to indicate the CR1400 is ready for use.

To aach a cable, plug the RJ-50 end of the Anity® cable into boom of the reader handle (Figure 1). Firmly push the connector into

the reader, unl a snap can be heard to indicate the cable is properly aached. To detach a cable, press a paper clip into the hole on the

side of the CR1400 handle (Figure 2), and gently pull the cable from the reader.

3.0 - Powering On/O the Reader

Figure 2

Figure 1

C006819_03_CR1400_User_Manual

4.0 - Using a CR1400 Out of a Universal Stand

Press and hold the CR1400 trigger, the two blue bars eming from

the reader are used for targeng. Center the blue bars in the middle

of a bar code. The opmal reading distance from reader to bar code is

approximately 4.0” (10 cm).

Once the reader is at the opmal distance, the reader will read the bar

code. The CR1400 will beep, ash a green LED and vibrate to indicate a

‘good read’ has occurred.

5.0 - Using a CR1400 in a Universal Stand

Revision 2 Hardware of the CR1400 has a stand detecon feature. By default,

when the CR1400 is placed in the stand, the reader will automacally enter

into moon detecon mode. When in this mode, simply place a bar code in the

scan eld to acvate the reader. The CR1400 will beep and ash a green LED to

indicate a ‘good read’ has occurred.

When the CR1400 is removed from the stand, the reader switches to manual

mode and the trigger must be pressed to read a bar code (refer to Secon 4.0).

Revision 1 Hardware of the CR1400 does not have an automac stand detecon

feature to enable moon detecon reading when the CR1400 is in a stand. To

congure this hardware revision for moon detecon scanning, please refer to

the CR1400 Conguraon Guide, located at www.codecorp.com/les.php and

scan the appropriate code.

See Secon 10.0 to learn how to determine your CR1400

hardware revision number.

To modify any default sengs, download the CR1400 Conguraon Guide

at www.codecorp.com/les.php and scan the appropriate code.

C006819_03_CR1400_User_Manual

6.0 - Reading Ranges

CR1400 Performance

Test Code Min Inches (mm) Max Inches (mm)

3 mil Code 39 3.9” (100 mm) 5.0” (125 mm)

7.5 mil Code 39 2.2” (55 mm) 8.0” (205 mm)

13 mil UPC 2.0” (50 mm) 10.8” (275 mm)

4.2 mil Data Matrix 3.7” (95 mm) 4.7” (120 mm)

5 mil Data Matrix 3.7” (95 mm) 5.5” (140 mm)

6.3 mil Data Matrix 3.1” (80 mm) 6.3” (160 mm)

10 mil Data Matrix 1.6” (40 mm) 7.9” (200 mm)

20.8 mil Data Matrix 1.6” (40 mm) 12.2” (310 mm)

Note: working ranges are a combinaon of both the wide and high density elds. All samples were high quality codes

and were read along a physical center line at a 10° angle. Default AGC sengs were used. Accuracy= +/- 10%.

7.0 - Reader Feedback

Scenario Top LED Light Sound Vibraon

CR1400 Successfully

Powers Up Green LED Flashes 1 Beep Handle Vibrates

CR1400 Successfully

Enumerates with Host

(via cable)

Once Enumerated,

the Green LED turns O 1 Beep Handle Vibrates

Aempng to Decode Green LED

Light is O None No Vibraon

Successful Decode and

Data Transfer Green LED Flashes 1 Beep Handle Vibrates

Conguraon Code

Successfully Decoded and

Processed

Green LED Flashes 2 Beep Handle Vibrates

Conguraon Code

successfully decoded

but wasn’t successfully

processed

Green LED Flashes 4 Beeps Handle Vibrates

C006819_03_CR1400_User_Manual

8.0 - Symbologies Defaulted On

Aztec

Codabar

Codablock F

Code 11

Code 39

Code 39 Short Margin

Code 93

Code 128

Code 128 Short Margin

Data Matrix

9.0 - Symbologies Defaulted O

Codablock F

Code 11

Code 39 Extended Full ASCII

Code 39 Checksum

Composite

Data Matrix Rectangle

Data Matrix Inverse

The following are symbologies that have a default of ON. To turn symbologies on or o, scan the symbology bar codes located in

the CR1400 Conguraon Guide located on our website at hp://www.codecorp.com.

The following are symbologies that have a default of OFF. To turn symbologies on or o, scan the symbology bar codes located in the

CR1400 Conguraon Guide located on our website at hp://www.codecorp.com.

All GS1 DataBar

Interleaved 2 of 5

MSI Plessy

NEC 2 of 5

PDF417

QR Code

Telepen

UPC

UPC Short Margin

Interleaved 2 of 5, 2 Digits

Macro PDF417

Maxicode

Matrix 2 of 5

Micro PDF417

OCR

Postal Codes - All Postal Codes

UPC-E Expansion

10.0 - Locang the Hardware Revision Number

Locate the serial label on the boom of the reader to idenfy the hardware revision number of the CR1400.

Serial #: 20000XXXX

MFG #: CR1411_02

Designed in USA.

Made in Malaysia.

The number aer the

underscore ( _ ) represents the

hardware revision number.

C006819_03_CR1400_User_Manual

11.0 - Reader ID and Firmware Version

Reader ID and Firmware

iVVVVWWWWXXXXSSSSSSSSSSAOODYYYYHHIIIIJJJJKKKKLLLL<TAB>Z…Z

To nd out the Reader ID and rmware version, open a text editor program (i.e., Notepad, Microso Word, etc.) and read the

following code:

You will see a text string indicang your rmware version and CR1400 ID number (see below):

i indicates ‘I’ string output;

VVVV is the applicaon rmware version number;

WWWW is the core applicaon rmware version number;

XXXX is reserved for the radio rmware version number;

SSSSSSSSSS is the Reader’s serial number (ten digits);

A is the current execuon state:

OO is the OEM idener;

D is the display type:

YYYY is the ash le system version number. Reserved;

HH is the hardware revision;

IIII is the hardware type idener: 0008 indicates a CR1400

JJJJ is the boot applicaon version;

KKKK is the operang system kernel version;

LLLL is the root le-system version;

<TAB> is the ASCII TAB character;

Z…Z is the OEM decoder version: a null terminated string of printable ASCII characters. Without a decoder.ini le,

the order of the decoders listed here indicates the order of use.

Example:

Xap/i3000300006040010002363A06D-SD+SQ

Note: Code will periodically release new rmware for CR1400 readers. For informaon on latest rmware versions,

call Code at (801) 495-2200. To upgrade rmware, please visit our website at hp://www.codecorp.com/

codesupport.php and follow instrucons provided.

“0” or “N” is no display device

“D” is the standard Keypad/Display

“A” means core is running

“B” means undened

“C” means undened

C006819_03_CR1400_User_Manual

12.0 - CR1400 Overall Dimensions

Table of contents

Code Code Reader 1400 User manual

Popular Barcode Reader manuals by other brands