Comelit Ultra Simplebus2 User manual

FREE DOWNLOAD
MYCOMELIT, L'APP PER IL PROFESSIONISTA
Ultra Simplebus2 audio module
art. UT2010, UT2010B, UT2010W
EN
TECHNICAL
MANUAL
MYCOMELIT: THE APP FOR PROFESSIONALS

2
Warning
Intended use
This Comelit product is designed and manufactured for use in the creation of audio and video communication systems in residential,
commercial, industrial and public buildings.
Installation
All activities connected to the installation of Comelit products must be carried out by qualified technical personnel, with careful
observation of the indications provided in the Manuals / Instruction sheets supplied with those products. The product must be installed
to the highest standards.
Wires
Disconnect the power supply before carrying out any operations on the wiring.
Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system manual.
We advise against running the system wires through the same duct as power cables (230V or higher).
Safe usage
To ensure Comelit products are used safely:
• carefully observe the indications provided in the Manuals / Instruction sheets,
• make sure the system created using Comelit products has not been tampered with / damaged.
Maintenance
Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance with the
indications provided in the Manuals / Instruction sheets.
Any repairs must be carried out:
• for the products themselves, exclusively by Comelit Group S.p.A.,
• for the systems, by qualified technical personnel.
Do not use alcohol or aggressive products for cleaning purposes.
Disclaimer
Comelit Group S.p.A. does not assume any responsibility for
• any purpose other than the intended use,
• failure to observe the indications and warnings contained in this Manual / Instruction sheet.
Comelit Group S.p.A. reserves the right to change the information provided in this Manual / Instruction Sheet at any time and without
prior notice.
Directives
The manufacturer, Comelit Group S.p.A., hereby declares that this equipment conforms to the applicable directives. The full
EU conformity declaration is available on the web page for the product.
In accordance with art. 26 of Italian Legislative Decree dated 14th March 2014, no. 49 “Implementation of directive 2012/19/
EU on Waste Electrical and Electronic Equipment (WEEE)”, the “crossed-out wheelie bin” symbol indicates that at the end of
its useful life, this product must be separated from other waste before collection for disposal. The user should therefore take
the exhausted appliance to suitable local collection centres for waste electrical and electronic products. As an alternative to
handling this process yourself, you can take the appliance to your local equipment dealer when purchasing a new equivalent
product. Electronics dealership businesses covering an area of 400 m² are also obliged to accept waste electronic products
smaller than 25 cm for disposal, without any obligation to purchase. Suitable separated waste collection for the subsequent
reuse of the appliance sent for recycling, processing and environmentally conscious disposal helps to avoid potential
negative eects on the environment and human health, and encourages the reuse and recycling of the materials used in the
construction of the appliance.

3
Table of contents
Warning ............................................................................................ 2
Description....................................................................................... 4
UT2010 ......................................................................................................4
Technical specifications ................................................................. 6
art. UT2010................................................................................................6
Installation........................................................................................ 7
Flush-mounted installation composition table....................................7
Surface-mounted installation composition table................................7
Flush-mounted installation............................................................. 8
Removing nameplates (2A) / module (2B)..............................................9
Installation with side-by-side boxes.....................................................10
Wall-mounted installation............................................................. 11
Removing nameplates (2A) / module (2B)............................................12
Installation with side-by-side boxes.....................................................13
Connections................................................................................... 14
Standard connection .............................................................................14
Connection with separate power supply .............................................14
Variants ...................................................................................................14
Module connection........................................................................ 15
Outdoor entrance panel module consumption table..........................15
powered by art. 1210/1210A ............................................................15
powered by additional power supply unit art. 1595 .........................15
Connection of button modules art. UT9200 .....................................16
Connection of Touchscreen module art. UT9270.............................16
Connection of number keypad module art. UT9279M .....................16
Variant with separate power supply..................................................16
Connecting digital call module art. UT9260M ..................................17
Programming ................................................................................. 18
Configuring the button type to maintain during normal operation
(single/dual) ............................................................................................18
Addressing button modules..................................................................18
Programming user codes ......................................................................18
Programming consecutive smart user codes............................. 19
Programming specific user codes............................................... 20
Special programming via DIP Switch .......................................... 21
Special programming table...................................................................22
Twilight sensor............................................................................... 24
Button backlighting management ........................................................24
Checking twilight sensor operation .....................................................25
Adjusting the brightness of the button LEDs ......................................26
Light-me function .......................................................................... 27
Light-me function behaviour on the basis of the LED backlighting
mode........................................................................................................27
Replacing the audio module with programming restore backup ....28
Configuring via PC......................................................................... 29
Errors and indications................................................................... 29
System functions........................................................................... 30
Operating distances...............................................................................31
Maximum system expansion.................................................................31
Maximum expansion per apartment.....................................................31
Wiring diagrams............................................................................. 32
System performance and layouts ................................................ 33
Table of user codes ....................................................................... 34

4
UT2010
Audio module for Ultra entrance panel, Simplebus2 system. For use in systems with power supply unit art. 1210 /
1210A.
Easy to install and simple to configure, thanks to the smart programming of call buttons.
Twilight sensor for automatic nameplate backlighting switch-off during daylight hours.
Omnidirectional digital microphone and double loudspeaker for high-fidelity audio.
Audio-visual indications for disabled individuals assistance request can be activated via programming.
Facility for 2 call buttons. To be finished with cap, single button or dual button made using aluminium or professional
grade plastic treated to prevent yellowing and dulling.
Adjustment and programming can take place without removing the module.
Dimensions: 100 x 90 x 35 mm.
ULTRA: the new and most technologically advanced entrance panel offering maximum ease of installation.
Available in flush-mounted or surface-mounted variants (protrusion from the wall just 10 mm and 35 mm
respectively), in silver (art. UT2010), black RAL9005 (art. UT2010B) and white RAL9010 (art. UT2010W).
Description
To make full use of the available functions, ALL modules making up the external
entrance panel must be updated to the latest firmware version, which is available to
download from the website pro.comelitgroup.com
Use ViP Manager software, available to download from the website
pro.comelitgroup.com, to carry out the update.

5
UP
13. 14. 15.3. 4. 5. 6.
9.10.11. 12. 8.
1.
7. 16.
17.
2.
1
2
1. Indicator LEDs
call sent (green) / system busy (red)
lock-release enabled
call in progress
2. Loudspeakers
3. Speaker volume control
4. S1 Button programming selector
5. S2 Special programming selector
6. Micro USB input for programming via computer
7. Jumper for power supply management (remove in case of
separate power supply)
8. Twilight sensor
9. Addressing and programming Dip Switches
10. Microphone volume control
11. Programming confirmation button
12. Digital microphone
Use screwdriver supplied
13. Terminal block for connection:
RTE programmable RTE (local lock-release
input) or DO input (door open indication)
GND SE- RTE and electric door lock input reference
negative
SE+ electric door lock connection
NO NC COM relay contacts
V- V+ power supply
LL bus line connection
14. Ethernet terminal block, only for use in case of additional
modules with LAN
15. Connector for additional modules with LAN
16. 17. Connector for additional module connection

6
Technical specifications
art. UT2010
GENERAL DATA
Type Modular
Product height (mm) 90
Product width (mm) 100
Product depth (mm) 35
Product colour Black RAL9005, Transparent Aluminium (art.UT2010), black (art.UT2010B), white
(art.UT2010W)
Product weight (g) 275
Coating material type Polycarbonate, Aluminium alloy
Flush mounting Yes, with specific accessory
Surface mounting Yes, with specific accessory
COMPATIBLE SYSTEMS
Simplebus 2 audio/video with power supply unit
art. 1210/1210A Yes
Simplebus 2 audio/video kit with power supply
unit art. 1209 Yes
Simplebus 2 audio with power supply unit art.
1210/1210A Yes
AUDIO SPECIFICATIONS
Microphone MEMS digital audio sensor, omnidirectional
Loudspeaker 28 mm (Ø), 8 Ohm, 1W (2)
Technologies implemented Full-Duplex
ELECTRICAL SPECIFICATIONS
Type of power supply Power supply via video entry bus
Power supply voltage 33 VDC
Absorption in standby (W) 1.5
Maximum absorption (W) 3.5
HARDWARE SPECIFICATIONS
Call type Buttons
Type of buttons Mechanical
Number of buttons (no.) 2
Backlighting colour White, O
Terminals L L V+ V- COM NC NO SE+ SE-/GND RTE TX- TX+ RX- RX+
Number of inputs (no.) 1
Number of outputs (no.) 2
Output type
Relay (C-NO-NC, 4A@12-24 VAC/VDC, inrush 10A), SE: 4A unlock pulse,
maintenance current 200 mA for 12 VAC/DC door locks (maximum impedance 18
Ohm)
Communication port Micro-USB
Twilight sensor Yes
SETTINGS
Loudspeaker volume Yes
Mic volume Yes
Backlighting brightness Yes
PROGRAMMING MODE
Manual (via Dip Switch) Yes
ViP Manager software Yes
ENVIRONMENTAL AND CONFORMITY
SPECIFICATIONS
IP protection rating (when installed) IP65
IK anti-vandal protection rating IK08
Operating temperature (°C) -25 to 55
Operating humidity (max RH - %) 25 to 95
Environmental class IV
Conformity and Certifications RoHS II - 2011/65/EU (EN IEC 63000:2018), EMC 2014/30/EU (EN 61000-6-1:2007,
EN 61000-6-3:2007+A1:2011)
MAIN FUNCTIONS
Lock-release Yes
Number of auxiliary relays (no.) 1
Input for local lock-release button Yes
Input for door open indication Yes
System status visual indications Yes
System status audio indications Yes
System status voice synthesis Yes

7
Flush-mounted box
3110/1
3110/1A 3110/2
3110/2A 3110/3
3110/3A 3110/4
3110/4A
Rain shield
UT9181
UT9181B
UT9181W UT9182
UT9182B
UT9182W
UT9184H
UT9183
UT9183B
UT9183W
UT9186 UT9189
UT9184
UT9184B
UT9184W
UT9188
Module holder/ finishing frame
UT9161
UT9161B
UT9161W UT9162
UT9162B
UT9162W UT9163
UT9163B
UT9163W UT9164
UT9164B
UT9164W
The entrance panel is available in flush-mounted or surface-mounted variants:
Flush-mounted installation composition table
A = Flush-mounted box
B = Rain shield
C = Flush-mounted module holder with finishing frame
Rain shield
UT9191
UT9191B
UT9191W UT9192
UT9192B
UT9192W
UT9194H
UT9193
UT9193B
UT9193W
UT9196 UT9199
UT9194
UT9194B
UT9194W
UT9198
Housing/frame
UT9171
UT9171B
UT9171W UT9172
UT9172B
UT9172W
UT9174H
UT9173
UT9173B
UT9173W
UT9176 UT9179
UT9174
UT9174B
UT9174W
UT9178
Surface-mounted installation composition table
A = Rain shield
B = Surface-mounted housing with frame
Optional
Installation

8
2
1
2
UP
53 4
165 cm
130 cm
1
Flush-mounted installation
BLACK
RED
Optional
Optional

9
6
1
A
B
C
C
2
+ Art. UT9110
MAX 0,2 mm
MAX 0,2 mm
9
1
2
10 12
2
1
11
CLACK!
CLACK!
1
2
3CLACK!
8
CLACK!
CLACK!
CLACK!
1
2
3
7
1
2
3
1
2
3
1
2A
1
3
2
4
2B
Removing nameplates (2A) / module (2B)
CLOSE
Kit art. UT9110 contains 5 sheets of pre-cut labels for nameplates and 1 sheet for the information module.
The sheets are made using Yupo paper which oers the ultimate transparency and resistance to atmospheric agents over time.
To print the labels, use the editable .pdf file which is available to download free of charge from the website pro.comelitgroup.com.
The button has a nameplate which can be written on (A);
alternatively, an adhesive label can be applied (B).
The total thickness of the nameplate + adhesive label
must not exceed 0.2 mm.
You can visit the website pro.comelitgroup.com to download
the PDF to print the entrance panel name cards, using the
adhesive pre-cut sheets (C) available in our catalogue (art.
UT9110 ).
Custom engraved Full Metal Ultra nameplates are available
on request. Find out how:
https://pro.comelitgroup.com/customised-nameplates-for-
ultra-entrance-panel

10
Installation with side-by-side boxes
Before installing the boxes in the wall, fit the spacers.
RED
BLACK

11
165 cm
130 cm
2
UP
53 4
UP
1
2
3
1
Wall-mounted installation
Optional
BLACK
RED
Optional

12
6
1
A
B
C
C
2
+ Art. UT9110
MAX 0,2 mm
MAX 0,2 mm
9
1
2
10
2
1
11 12
CLACK!
CLACK!
1
2
CLACK!
3
8
CLACK!
CLACK!
1
2
CLACK!
3
7
1
2
3
1
2
1
3
2A
1
3
2
4
2B
Removing nameplates (2A) / module (2B)
CLOSE
The button has a nameplate which can be written on (A);
alternatively, an adhesive label can be applied (B).
The total thickness of the nameplate + adhesive label
must not exceed 0.2 mm.
You can visit the website pro.comelitgroup.com to download
the PDF to print the entrance panel name cards, using the
adhesive pre-cut sheets (C) available in our catalogue (art.
UT9110 ).
Custom engraved Full Metal Ultra nameplates are available
on request. Find out how:
https://pro.comelitgroup.com/customised-nameplates-for-
ultra-entrance-panel
Kit art. UT9110 contains 5 sheets of pre-cut labels for nameplates and 1 sheet for the information module.
The sheets are made using Yupo paper which oers the ultimate transparency and resistance to atmospheric agents over time.
To print the labels, use the editable .pdf file which is available to download free of charge from the website pro.comelitgroup.com.

13
Installation with side-by-side boxes
RED
BLACK

14
1210A
1210
UT2010
E
T
R
GND
SE
-SE
+
NO NC
C
O
M
LL
+
VV
-
12 VAC/VDC
18 Ω MAX
-
+
120-230 V
1595
1210A
1210
E
T
R
GND
SE
-SE
+
NO NC
C
O
M
LL
+
VV
-
J4 J4
UT2010
12 VAC/VDC
18 Ω MAX
12 VAC/VDC
18 Ω MAX
E
T
R
GND
SE-SE
+
NO NC
C
O
M
LL
+
VV
-
1210A
1210
10A MAX
AC-DC
12V/24V
10A MAX
AC-DC
12V/24V
E
T
R
GND
SE-SE
+
NO NC
C
O
M
LL
+
VV
-
1210A
1210
ON
1 2 3 4 6 75 8
UT2010
UT2010
Connections
Standard connection
Connection with separate power supply
Max 20 m. Local door-opener button.
Max 20 m. Local door-opener button.
“C.NC.NO relay activation on actuator command: 2 sec”
fSet DIP switch 8 to ON permanently (as shown in the
figure)
Max 20 m. Local door-opener button.
Variants
Variant for using the outdoor entrance panel relay Variant for using a safety door lock

15
UP
LL
UP
LL
V+V-
J4
Module connection
For systems with art. UT2010 and power supply unit art. 1210/1210A, the maximum power available for the
outdoor entrance panel modules is 3.3 W.
Calculate the total power consumption of the modules in your system configuration using the Consumption
table.
If the total power consumption of the modules exceeds
3.3 W , connect a supplementary power supply
unit (art. 1595) to the V+ and V- contacts of the outdoor entrance panel, as shown in the figure below (see
Connection with separate power supply). In any case, the total absorption must be lower than
16.5 W .
Outdoor entrance panel module consumption table
powered by art. 1210/1210A
A B powered by additional power supply unit art. 1595
Code Absorption (W)
UT9200 Call button modules 0.41
UT9240 Information module 0.41
UT9240M Metal information module 0.41
UT9279M Number keypad module
1.32 Relays disabled and audio or audio/video
module SE output used
2.47 With 1 bistable relay active
3.3 With 2 bistable relays active at the same
time
UT9310M Magnetic induction module 8.1 Always needs to be powered by additional
power supply unit Art. 1595
UT9270 Touchscreen module 3.3
In systems with an outdoor entrance
panel consisting of 1 audio or audio/video
module, Touch module art. UT9270 and up
to 80 users, it is not necessary to provide
any additional power supply.
For all other combinations, provide an
additional power supply unit art. 1595
UT9260M Digital directory module 1.98

16
1210A
1210
UT9279M
E
T
R
GND
SE
-SE
+
NO NC
C
O
M
LL
+
VV
-
UT2010
12 VAC/VDC
18 Ω MAX
UP
MAX 8
1210A
1210
UT9200
E
T
R
GND
SE
-SE
+
NO NC
C
O
M
LL
+
VV
-
UT2010
12 VAC/VDC
18 Ω MAX
1210A
1210
UT9270
E
T
R
GND
SE
-SE
+
NO NC
C
O
M
LL
+
VV
-
1210A
1210
E
T
R
GND
SE
-SE
+
NO NC
C
O
M
LL
+
VV
-
J4
UT9270
8O utenti
massimo > 8O utenti
UT2010 UT2010
-
+
120-230 V
1595
12 VAC/VDC
18 Ω MAX
12 VAC/VDC
18 Ω MAX
Connection of button modules art. UT9200
Connection of Touchscreen module art. UT9270 Variant with separate power supply
Connection of number keypad module art. UT9279M
Max 20 m. Local door-opener button.
Max 8 modules (Max 30 modules with additional power supply).
Max 20 m. Local door-opener button.
For systems with over 80 users, provide an additional power supply
Max 20 m. Local door-opener button.
RED
BLACK
Maximum
80 users > 80 users

17
1210A
1210
E
T
R
GND
SE
-SE
+
NO NC
C
O
M
LL
+
VV
-
UT2010
12 VAC/VDC
18 Ω MAX
UT9260M
Connecting digital call module art. UT9260M
Max 20 m. Local door-opener button.

18
65
default
65
ON
OFF
1
ON
2 3 4 65
8765 8765
default
ON
OFF
1
ON
2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
1
2
4
3
5
Programming
For correct programming, follow the instructions below in order
I. Configure button type
II. Address button modules
III. Program user codes
code
DIP ON
1112 3,4 23 1,2,3,5
2213 1,3,4 24 4,5
31.2 14 2,3,4 25 1,4,5
4315 1,2,3,4 26 2,4,5
51,3 16 527 1,2,4,5
62,3 17 1,5 28 3,4,5
71,2,3 18 2,5 29 1,3,4,5
8419 1,2,5 30 2,3,4,5
91,4 20 3,5 31 1,2,3,4,5
10 2,4 21 1,3,5
11 1,2,4 22 2,3,5
TAB. A
Configuring the button type to maintain during normal operation (single/dual)
DIP 6: configuring button type:
Single button (DIP6 ON).
Dual button (DIP6 OFF, default).
I
Addressing button modules
DIP 1-5: addressing call button module (see TAB. A)
Addressing call button modules means that, in the event they are replaced, it is not necessary to reprogram
the user codes associated with the buttons. All you need to do is assign the same address as before to the new
module.
II
Programming user codes
There are 2 programming methods:
• Programming consecutive smart user codes: allows quick programming of buttons with consecutive user codes
(e.g.: 1, 2, 3, 4)
• Programming specific user codes: allows programming of specific user codes (e.g.: 25, 37, 70, 58)
III
DIP 6: configuring button type:
Single button (DIP6 ON).
Dual button (DIP6 OFF, default).

19
LL
1
8765
default
OFF
8765
ON
2
OFF
ON
1 2 3 4 6 75 8
4
S1 S2
3
ON
1 2 3 4 6 75 8
5
= 1
6
= 2
+1 = 3
+1 = 4 +1 = 5
+1
7
S1 S2
8
8765
default
OFF
8765
ON
9
Programming consecutive smart user codes
example:
code 1
Set the user code of the apartment
you wish to call (for example:1)
using the DIP-switches
(see Table of user codes )
DIP 6: configuring
button type:
Single button (DIP6
ON).
Dual button (DIP6
OFF, default).
Press the button you want to
associate with the user code set
using the DIP-switches
Press the following buttons to assign consecutive user codes.
BEFORE you proceed:
Set
ALL DIP-switches to OFF, including
DIP 6.
DIP 6: configuring
button type:
Single button (DIP6
ON).
Dual button (DIP6
OFF, default).

20
LL
1
S1 S2
8
8765
default
OFF
8765
ON
9
OFF
ON
1 2 3 4 6 75 8
4
S1 S2
3
ON
1 2 3 4 6 75 8
5
8765
default
OFF
8765
ON
2
= 25
6
ON
1 2 3 4 6 75 8
ON
1 2 3 4 6 75 8
ON
1 2 3 4 6 75 8
37
70 58
7
Programming specific user codes
Press the button you want to
associate with the user code set
using the DIP-switches
Repeat steps 4 and 5 to assign a specific user code to each button
example: code 37 example: code 70 example: code 58
DIP 6: configuring
button type:
Single button (DIP6
ON).
Dual button (DIP6
OFF, default).
example:
code 25
Set the user code of the apartment
you wish to call (for example:25)
using the DIP-switches (see Table of
user codes )
DIP 6: configuring
button type:
Single button (DIP6
ON).
Dual button (DIP6
OFF, default).
BEFORE you proceed:
Set
ALL DIP-switches to OFF, including
DIP 6.