Comeup Seal Gen2 12.5rs User manual

Self-Recovery Winch
Model: Seal Gen2 20.0rs
PN: 295223 12V
Introduction
Feature
Line pull: 9,072 kg / 20,000 lb synthetic rope first layer
Wire rope: 14 mm × 16.7 m (9/16"×55′) synthetic rope
Brake: Patented cone brake holds full load
Clutch: Turn the T-handle for rapid wire rope payout
Control: Handheld pendant switch powers the winch
Unpacking
．Winch assembly……………………………………………………....... 1 pc
．Potted control box…………………………………............................. 1 pc
．Remote control………………………………………………………….. 1 pc
．Synthetic rope with sling hook..……………………………………….. 1 pc
．Hawse fairlead……………………………………………………..……. 1 pc
．1.8 m (6′) 2 gauge battery lead……………………………………….. 1 pc
．Wireless Transmitter……………………………………………………. 1 pc
Read this manual carefully
You should carefully read and understand this manual before operating it.
Careless winch operation may result in personal injury hazards or property
damage.
Installation
Before using the winch, make sure all
electrical components have no corrosion or
damaged; the environment should be clear
and dry.
Winch and hawse fairlead mountings
．It is very important that the winch will be
mounted on a flat and hard surface of
mounting channel in order to make sure the motor, drum and gearbox
housing are aligned correctly.
．Hawse fairlead does not mount to the winch directly.
．The synthetic rope shall be wound in an under-wound orientation only.
．Eight (8) M12 x 1.75 pitch 12.9 grade w/137 N-m torque setting (maximum)
high tensile steel bolts must be used in order to sustain the loads imposed
on the winch mounting.
．
Two (2) M10 x 1.50 pitch stainless steel bolts must be used for fastening the
hawse fairlead into the mounting channel.
Wiring Diagram
Attach the black lead firmly to the negative (–) battery terminal and red lead
to the positive (+) battery terminal. The voltage drop for the winch motor
must not exceed 10% of the nominal voltage of 12V DC.
Nut fastening for motor & contactor
1. Holding the lower nut on the stub and fastening the upper nut clockwise.
2. The torque setting for nut is 14 N-m/124 lb-in.

Warning
．The winch is not intended to be used in any manner for the movement or lifting
of personnel.
．The rated line pull shown is based on the first layer of rope on the drum.
．The rope winding on the drum shall remain 10 wraps from the drum.
．Manufacturer is not responsible for the results of misuse, misapplication, faulty
installation or abuse of synthetic rope in any way.
Parts List
Item No. Description Part No. Qty
1 Waterproof motor w/housing 12V 883674 1
2 Tie bar ki
t
882856 3
3 Motor coupling 882201 1
4 Drum bushing 880048 1
5 Drum ki
t
882202 1
6 Drum bushing 882204 1
7 Gearbox support rack 882900 1
8 Grounding lead 880009 1
9 Synthetic rope 883676 1
10 Sling hook 883677 1
11 1s
t
shaf
t
882206 1
12 3r
d
ring gear kit 882208 1
13 3r
d
stage carrier 882210 1
14 2n
d
stage carrier 882211 1
15 1s
t
stage carrier 882212 1
16 1s
t
pinion 882213 1
17 Clutch ki
t
882214 1
18 Gear box ki
t
882215 1
19 Cone brake disc kit 882216 1
20 Brake clutch base 882217 1
21 Brake cover kit 882423 1
22 Hawse fairlead 883410 1
23 Mounting hardware 882854 1
24 Remote control 880126 1
25 Handsaver strap 880026 1
26 Control box 12V 882780 1
26-1 Remote socket kit 881491 1
26-2 Control pack 12V 882846 1
26-2-1 Wireless receiver 882800 1
26-3 Wireless transmitter 883822 1
Winch Assembly
2021/09/16 Ver:3