CommScope AEKT User manual

Part Lists
ITEM NO. DESCRIPTION
AEKTMNT
QUANTITY
IMAGE
1 RADOME ASSEMBLY -
2 WIND SHIELD,MIDDLE -
3 WIND SHIELD,BOT -
4 WIND SHIELD,TOP -
5 SCREW ASSY M5 X 16,SS316 -
6 SPACER,PLASTIC,ANTI-FALL -
7 PIPECLAMP BRACKET NO FLANGE,AEKT 2
8 MOUNTING BRACKET,AEKT 2
9 MOUNTING BRACKET -
10 PIPECLAMP BRACKET,W/ PIN 2
11 BOLT,CARRIAGE,M12X200,STL,GALV 4
12 SCR,W/ WSHR,M6X20,SS316 8
13 NUT,HEX,M12,STL,GALV 20
14 WSHR,FLT,M12,13X24X2.5,STL,GALV 8
15 SCR,HCS,HEX,M12X40,STL,GALV 4
16 WSHR,LK,SPLT,M12,STL,GALV 8
17 MAINTENANCE WIRE 1
18 SCR,HCS,HEX,M10X40,STL,GALV 4
19 WSHR,LK,SPLT,M10,STL,GALV 4
20 NUT,HEX,M10,STL,GALV 8
AEKT For S4-90M-R1-V2 Antennas
AEKT: Antenna Enclosure KiT, including EMPTY BOX and AEKTMNT.
AEKTMNT: mounting kit of AEKT for cylindrical pipe installations (60-115 mm pipe diameter) for heavy duty
applications.
This document explains how to install AEKT with AEKTMNT and how to replace the wind shield with S4-90M-R2-V2.
639853 Revision B, SEP 2019
Page 1 of 4
www.commscope.com
© 2019 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639853 B (09/19)

12
M6 bolt
17
Snap the hook
of maintenance
wire here
EMPTY BOX
13 16 14 7
Passive Antenna
16 18
8
151413 19 20
M10 bolt
M12 bolt
M12 bolt
10
13
11
GAP
Do not hit the endcap of the passive antenna
during installation. Leave 5 mm gap between
two endcaps.
Step1 Assemble the EMPTY BOX
Step2 Mount the EMPTY BOX
assembly to the pole
AEKT EMPTY BOX installation
Store extra brackets for future use
If the brackets lost, purchase AEKTBKT
Pre-Assembly of pipe bracket
MAXIMUM TORQUE
M6 8.0N.m (6ft.lbs)
M12 58N.m (43ft.lbs)
639853
Page 2 of 4
www.commscope.com
© 2019 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639853 B (09/19)

These four screws
and plastic spacers
are always kept
installed on wind
shield.
13 16 14 7
Passive antenna
1
141613
Pre-bend cable
per cable installation
instruction. Tie the
cable here
17
Fix the wind shield
after jump cables
are installed
Maintenance
wire is to prevent
the wind shield
from falling while
maintaining the
antenna.
Step 5 Mount the antenna assembly on the pole
14 15 16
M12 bolt
18 19 20
M10 bolt
GAP
Step 2 Disassemble the EMPTY BOX
Instruction of replacing wind shield with S4-90M-R1-V2
Step1 Remove the EMPTY BOX assembly from the pole
Step 3 Assemble the antenna and bracket
Step 4 Assemble the antenna and radome
Do not hit the endcap of the passive antenna
during installation. Leave 5 mm gap between
two endcaps.
MAXIMUM TORQUE
M5 4.6N.m (3ft.lbs)
M6 8.0N.m (6ft.lbs)
M10 37N.m (27ft.lbs)
M12 58N.m (43ft.lbs)
639853
Page 3 of 4
www.commscope.com
© 2019 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639853 B (09/19)

Lift here
SAFETY NOTICE
The installation, maintenance, or removal of an antenna
requires qualified, experienced personnel. CommScope
installation instructions are written for such installation
personnel. Antenna systems should be inspected once a
year by qualified personnel to verify proper installation,
maintenance, and condition of equipment.
CommScope disclaims any liability or responsibility for the
results of improper or unsafe installation practices.
It is recommended that transmit power be turned off
when the field installation is performed. Follow all
applicable safety precautions as shown on this page.
Do not install on a wet or windy
day or when lightning or thunder
is in the area. Do not use metal
ladder.
Do not install near power lines.
Power lines, telephone lines,
and guy wires look the same.
Assume any wire or line can
electrocute you.
Wear shoes with rubber soles and
heels. Wear protective clothing
including a long-sleeved shirt and
rubber gloves.
The female RF connectors fitted to the antenna are designed
to fit jumper cables with standard related male RF connector.
Tighten the RF connector coupling according to torque
specification in antenna label, if the RF connectors are
tightened beyond the recommend torque, the RF connection
to the antenna may be damaged.
RF Cable Connection
The AISG connector fitted to the antenna is designed to accept
any AISG compliant cable assembly, commscope recommends
hand tightening AISG mating connector only. Applied torque to
the connector shall not exceed 1.5N*m.
Remote Electrical
Tilt Connection
Lift here
Instruction of lifting points
639853
Page 4 of 4
www.commscope.com
© 2019 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 639853 B (09/19)