CommScope Flex Frame Splice Cabinet User manual

TC-96272-IP
Rev A, June 2019
commscope.com
User
Manual
Flex Frame Splice Cabinet
860649686 Rev A
© 2019 CommScope, Inc. Page 1 of 20
Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Related Publications. . . . . . . . . . . . . . . . . . . . . . . . . .2
1 Product Description. . . . . . . . . . . . . . . . . . . . .2
1.1 General Description. . . . . . . . . . . . . . . . . . . . .2
1.2 Typical Flex Frame Application. . . . . . . . . . . .4
1.3 Dimensions and Specifications . . . . . . . . . . . .5
2 Unpacking and Inspection. . . . . . . . . . . . . . . .6
3 Overview of Installation. . . . . . . . . . . . . . . . . .6
4 Mounting the Cabinet . . . . . . . . . . . . . . . . . . .6
4.1 Mounting Options . . . . . . . . . . . . . . . . . . . . . .6
4.2 Tools Required . . . . . . . . . . . . . . . . . . . . . . . .6
4.3 Frame Mounting . . . . . . . . . . . . . . . . . . . . . . .7
4.4 Wall Mounting on Brackets . . . . . . . . . . . . . . .8
5 Installing Cables and Loading Splice Trays .10
5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
5.2 Installing Splice Trays . . . . . . . . . . . . . . . . . .12
5.3 Removing Splice Trays . . . . . . . . . . . . . . . . .14
5.4 Breaking Out Side Entry Cables (from non-Flex-
Frame Panels) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
5.5 Breaking Out Facility Cables. . . . . . . . . . . . .14
5.6 Securing Facility Cables . . . . . . . . . . . . . . . .16
5.7 Loading Splice Trays. . . . . . . . . . . . . . . . . . .18
5.8 Performing Splices . . . . . . . . . . . . . . . . . . . .19
5.9 Changing Splice Trays . . . . . . . . . . . . . . . . .19
6 Contact Information. . . . . . . . . . . . . . . . . . . .20
Introduction
This user manual describes the Flex Frame
Splice Cabinet and provides directions for
installing this product. Procedures include:
• Unpacking the cabinet
• Mounting the cabinet on a Flex
Frame or wall
• Preparing cables for installation
• Installing cables
• Setting up splices
This user manual also lists related
publications and tells how to obtain technical
assistance.
Flex Frame Splice Cabinet

Page 2 of 20. © 2019 CommScope, Inc.
TC-96272-IP
Related Publications
The following related publications are available by contacting the online Commscope Support
Center at https://www.commscope.com/SupportCenter
•Ribbon Cable Breakout (RIBCBOUT) Kits User Manual (TC-96271-IP) -- provides a
high-level overview of and basic installation instructions for the CommScope RIBC-
BOUT (Ribbon Cable Breakout) series ribbon fiber cable breakout kits utilizing expand-
able mesh sleeve material to provide protection and transportation for the fiber ribbons
from the point of exit from the cable sheath to the tie-down point on the fiber splice tray
or wheel. The kits are applicable for both standard matrix and “rollable” style fiber rib-
bons in slotted core, central tube, or loose buffer tube cable constructions, and for cable
counts ranging from 144-fiber to 3456-fiber.
•Cable Clamp Kit Installation Drawings- contain instructions for the cable clamps kits
listed in this user manual. These instructions ship with the kit, and can also be obtained
using https://www.commscope.com/SupportCenter
1 Product Description
1.1 General Description
The Flex Frame Splice Cabinet is a compact splice enclosure that provides a splicing interface
between “panel stubs” and facility cables.
In a Flex Frame application, panel stubs originate in the Flex Frame in pre-terminated Enhanced
High Density (EHD) or Compact High Density (CHD) panels. Panel stubs are covered with mesh
tubing rather than a sheath, and contain rollable ribbons, each with 12 fibers.
Facility cables are high-fiber-count cables, likewise containing rollable ribbons, and of a type
suitable for being routed indoors or outdoors as required.
The Flex Frame Splice Cabinet is also available in a stand alone kit with wall mounting brackets,
providing the option of mounting the cabinet on a wall. In this case, the cabinet can be used with
other types of panels and cables if they are comparable in function and structure to those used in
a Flex Frame application. Cables from non-Flex-Frame panels (called “right-entry cables” in this
user manual) may need to broken out per the instructions and breakout diagram provided in
Section 5.4 on page 14.
The splice cabinet accommodates up to 24 splice trays, each with a capacity of up to 288 rollable
ribbon, mass fusion splices, for a total of 6912 splices. In a Flex Frame application, the capacity
is 5184 splices (for panels with LC connectors).
Figure 1 shows the interior components of the splice cabinet loaded with splice trays.
Table 1: Cable Clamp Documentation
Cable Clamp Kit Installation Drawing
NG4-FLXACCSMCMP A180014150
FEC-ACCCLMP01 1029951
OSP-CLPFEC-XL-1 300100115081

TC-96272-IP
© 2019 CommScope, Inc. . Page 3 of 20
Figure 1. Interior Components of Flex Frame Splice Cabinet
The interior components shown in Figure 1 are as follows:
•Splice trays -- are FOST-ACC-D-TRAY-RR-288 trays, up to 24 (2x12) in total. The
splice trays mount on a bracket and are held in place with hook-and-loop straps. Unfas-
tening the strap for a particular splice tray allows the tray to hang down for examination.
A splice tray can be easily removed to an adjacent work surface for fiber routing and
splicing.
•Entry for facility cables -- is a brush-lined opening through which facility cables enter
the cabinet.
•Entry ports for panel stubs -- each accommodate one panel stub, containing either
288 or 576 fibers, as described in Section 1.2.
26899-A
FRONT
OBLIQUE
VIEW
NORMAL
FRONT
OBLIQUE
VIEW
EXPLODED
FOST D
SPLICE
TRAY
STACK OF
SPLICE
TRAYS
FACILITY
CABLES
(REF)
CABLE
MOUNTING
BRACKETS
(NOT
VISIBLE)
ENTRY
PORTS
FOR
PANEL
STUBS
(18X)
WALL
MOUNTING
BRACKET
(REF)
TRAY
HOLDER
BRACKET
(2X)
RADIUS
LIMITER
(6X)
ENTRY FOR
FACILITY CABLES

Page 4 of 20. © 2019 CommScope, Inc.
TC-96272-IP
•Cable Mounting Brackets -- accommodate different types of cable clamps as required
for the different sizes and combinations of cables that can be installed.
1.2 Typical Flex Frame Application
Figure 2 shows a typical splice cabinet installation on a Flex Frame loaded with 2RU EHD or CHD
panels. In this example, three 1728-fiber facility cables are broken out into six 288-fiber sub-
units, which are spliced to six 288-fiber panel stubs from six 2RU panels.
Figure 2. 2RU Flex Frame Application Example
Other features to observe in this sample Flex Frame 2RU application are:
•Panel stubs -- from 2RU panels each contain a stack of twenty-four 12-fiber rollable rib-
bons protected by mesh tubing (24x12=288). (Alternatively, as noted above, panel stubs
from 4RU panels each contain forty-eight 12-fiber ribbons (48x12=576).)
•Facility cables -- have a total fiber count divisible into sub-units appropriate for the
application. Typically, the sub-unit is 288 fibers, but other configurations are possible,
Note: An alternative Flex Frame application employs 4RU panels. In a 4RU configuration, the
panel stubs each contain 576 fibers, and each stub is routed through a single entry port
to two splice trays.
26594-A
2RU EHD/CHD PANELS
EACH HAS 288 TERMINATIONS
(WITH LC CONNECTORS)
PANEL STUBS
EACH 288 FIBERS
FLEX FRAME SPLICE CABINET
FACILITY CABLES
(IN THIS EXAMPLE,
EACH HAS
1728 FIBERS)
FACILITY CABLE
SUB-UNITS
(EACH GOES TO ONE
SPLICE TRAY)
SPLICE
TRAYS
(9 IN EACH
STACK)
FAR END EQUIPMENT
NOTE: FACILITY
CABLES MUST BE
DIVISIBLE INTO
SUB-UNITS OF
288 FIBERS
OR LESS.

TC-96272-IP
© 2019 CommScope, Inc. . Page 5 of 20
such as a 432-fiber cable broken out into two 216-fiber sub-units, each of which is
routed to one splice tray.
1.3 Dimensions and Specifications
Figure 3 shows the splice cabinet dimensions. Table 2 lists specifications. Table 3 summarizes the
capacity of a splice cabinet when used in a Flex Frame application.
Figure 3. Flex Frame Splice Cabinet Dimensions
Table 2: Specifications
Parameter Specification
Dimensions (H x W x D) 66.58 in.(169.1cm) x 14.64 in.(37.19cm) x 10.27 in. (26.
07cm)
Weight 40 lbs. (110.2 Kg)
Splice tray used FOST-ACC-D-TRAY-RR-288-KIT
Number of splice trays Up to 24 (2 stacks of 12 trays)
Total number of splices Up to 6912 mass fusion splices
Cable type 12-fiber rollable ribbon
Fiber count 6912 in, 6912 out
Mounting options Can be mounted on a Flex Frame or on a wall using wall
mounting brackets (see Section 4.1)
26594-A
66.58 IN.
(169.12 CM)
14.64 IN.
(37.19 CM)
10.27 IN.
(26.07 CM)

Page 6 of 20. © 2019 CommScope, Inc.
TC-96272-IP
2 Unpacking and Inspection
1. Inspect the exterior of the shipping container(s) for evidence of rough handling that may
have damaged the components in the container.
2. Unpack each container while carefully checking the contents for damage.
3. If damage is detected or if parts are missing, file a claim with the commercial carrier and
notify CommScope Support Center at https:wwwcommscope.com//SupportCenter
4. Save all shipping containers for use if the equipment requires shipment at a future date.
3 Overview of Installation
The main steps in installation are:
• Mounting the cabinet on a Flex Frame or wall
• Preparing and installing cables
• Loading splice trays
4 Mounting the Cabinet
4.1 Mounting Options
The cabinet may be mounted on the Flex Frame or on a wall if mounting with wall mounting
brackets. Catalog numbers vary for different mounting.
• Mounting to Flex Frame (760242402, cabinet shipped with Flex Frame)
• Mounting to Flex Frame (760242404, cabinet alone)
• Mounting to wall (760243212, cabinet alone, shipped with wall mounting brackets)
4.2 Tools Required
• Phillips #2 screwdriver
• Level (when wall mounting)
Table 3: Splice Cabinet Capacity in Flex Frame Application
Parameter Specification
Total number of splices 5184 mass fusion, rollable ribbon splices
Number of splice trays 18 (FOST-ACC-D-TRAY-RR-288-KIT)
Panel stubs 18 rollable ribbon cable stubs (each has twenty-four 12-fiber
ribbons)
Facility cables Common applications include nine 576-fiber cables, six 864-
fiber cables, or three 1728-fiber cables
Flex Frame panels Eighteen EHD or CHD 2RU panels or
nine EHD or CHD 4RU panels

TC-96272-IP
© 2019 CommScope, Inc. . Page 7 of 20
4.3 Frame Mounting
The splice cabinet is mounted on the right rear side of the cable management panel of the Flex
Frame. Use the following procedure, referring to Figure 4.
1. Remove the door from the front of the splice cabinet.
Figure 4. Mounting the Splice Cabinet on the Flex Frame
26890-A
REAR
OBLIQUE
VIEW
#12-24 SCREWS
& WASHERS (6X)
FLEX FRAME
SPLICE
CABINET
SPLICE
CABINET
DOOR
ACCESSORY
RAIL (2x)
FLEX FRAME
CABLE MANAGEMENT PANEL
(REAR SIDE)
FLEX FRAME

Page 8 of 20. © 2019 CommScope, Inc.
TC-96272-IP
2. Install two #12-24 screws without washers in the top two holes of the accessory rails on
the back of the Cable Management Panel of the Flex Frame as shown in Figure 4.
Figure 5. Key Hole Location on Back Interior Wall of Splice Cabinet
3. Hang the cabinet on the two screws just installed, using the cabinet mounting keyholes
shown in Figure 5.
4. Fasten splice cabinet to cable manager accessory rails with additional #12-24 screws
(4x) and star washers (4x), as shown in Figure 4. Start all fasteners before tightening.
5. Ground the splice cabinet in the location shown in Figure 6.
Figure 6. Grounding the Splice Cabinet
4.4 Wall Mounting on Brackets
Figure 7 shows the features of the wall mounting brackets. Use the following procedure referring
to Figure 8.
Figure 7. Wall Mounting Bracket
Note: Install the screws part way only.
26894-A
KEYHOLE (2X)
FOR
HANGING
SPLICE
CABINET
ON
ACCESSORY
RAIL
26595-A
GROUND
LOCATION
26596-A
16.0 IN. (40.4 CM)
3.5O IN.
(26.07 CM)
MOUNTING HOLE (8X)
DIAM. 0.27 IN. (0.68 CM)
0.75 IN.
(1.91 CM)
HORSE SHOE HOLE
FOR LEVELING CABINET

TC-96272-IP
© 2019 CommScope, Inc. . Page 9 of 20
1. Remove the door from the front of the splice cabinet.
Figure 8. Mounting the Splice Cabinet on a Wall
2. On the rear side of the cabinet, install the mounting bracket on the cabinet using the
#12-24 screws provided. The top and bottom brackets are identical in design. Select
from the possible hole configurations drilled into the back wall of the cabinet.
3. Install a single support screw in the wall to temporarily hold the top mounting bracket
Place the screw in the top center of the desired cabinet location.
4. Hang the cabinet on the wall by positioning the middle horseshoe opening (shown in
Figure 7 on Page 8) on the support screw just installed. Level the cabinet.
5. Secure the cabinet in a level position using appropriate wall mounting hardware on both
sides. Install the hardware from inside of the cabinet into the wall material.
Note: Install the screw part way only.
26897-A
REAR
OBLIQUE
VIEW
#12-24 NUTS
& WASHERS (6X)
FLEX FRAME
SPLICE CABINET
SPLICE
CABINET
DOOR
WALL
MOUNTING
BRACKET (2X)

Page 10 of 20. © 2019 CommScope, Inc.
TC-96272-IP
5 Installing Cables and Loading Splice Trays
5.1 Overview
Panel stubs originate in panels mounted on an adjacent frame. Facility cables originate in other
equipment, inside or outside of the building. Panel stubs come in from the left and are routed in
the area left of the splice decks. Facility cables come in from the top and are routed in the area
right of the splice decks. Splice trays are typically removed to a nearby work area for fiber routing
and splicing. When a splice tray is returned to the cabinet, the slack is lifted over the cable man-
agement on the appropriate side of the splice deck as shown in Figure 9. Slack for subsequent
splice trays is nested neatly within the slack loops already present. Slack for upper and lower
splice decks is kept separate.
Figure 9. Cable Routing in Splice Cabinet
26911-A
PANEL
STUB
PORTALS
(24x)
UPPER
SPLICE
DECK
ROUTING
FACILITY
CABLE
ENTRY
CABLE
SLACK
TAKEUP
FIXTURE
CABLE
SLACK
TAKEUP
FIXTURE

TC-96272-IP
© 2019 CommScope, Inc. . Page 11 of 20
Panel stubs on Flex Frame EHD and CHD panels will already be broken out to the required
dimensions. Cables from non-Flex-Frame panels must be broken out to the dimensions provided
in Section 5.4 on page 14. Panel stubs and equivalent cables from non-Flex-Frame panels are not
secured within the cabinet. They simply enter through the side and the slack is dressed into the
slack management features.
Facility cables must be broken out to the dimensions provided in Section 5.5 on page 14. This may
be done for all cables at the same time, before loading splice trays, or it may be done for the
associated cable as each splice tray is loaded. Breakout kits are required for facility cables. The
RIBCBOUT kits described in TC-96271-IP (see “Related Publications” on page 2) are advised. RIB-
CBOUT kits include cable clamps. Cable clamps are also available for cables not being installed
with RIBCBOUT kits (see Table 5 on page 16).
Figure 10. Cable Routing in Splice Cabinet Top Splice Deck

Page 12 of 20. © 2019 CommScope, Inc.
TC-96272-IP
5.2 Installing Splice Trays
The FOST-ACC-D-TRAY-RR-288 trays used in the splice cabinet are shipped in separate pack-
ages. Use the following procedure to install the splice trays in the cabinet.
1. Unpack the splice trey. Refer to Figure 11. There are two per box.
Figure 11. Unpacking the Splice Tray
2. Hold the splice tray vertically over the tray holder bracket, and insert the tray hinge into
the designated slot on the tray holder bracket. Lift the red tray support latch up to lower
the tray. Refer to Figure 12.
Figure 12. Inserting the Tray in the Tray Holder Bracket

TC-96272-IP
© 2019 CommScope, Inc. . Page 13 of 20
3. Take the second splice tray and in a similar manner install it in the designated slot. Refer
to Figure 13.
Figure 13. Installing the Second Splice Tray
4. When done installing trays in a particular tray holder bracket, lift the trays up together
and fasten them in place using the hook-and-loop strap.Refer to Figure 14.
Figure 14. Inserting the Top of the Splice Tray in the Splice Tray Bracket

Page 14 of 20. © 2019 CommScope, Inc.
TC-96272-IP
5.3 Removing Splice Trays
After being installed, a splice tray can be removed. For example, this is done when moving the
splice tray to a work surface to perform splices.To remove a splice tray from the tray holder
bracket, use the following procedure.
1. Unfasten the hook-and-look strap.
2. Lift up the splice trays above the tray of interest and fasten them in place using the hook
and hook-and-loop strap.
3. Take hold of the tray of interest and pull the tray hinge out of the tray holder bracket.
4. If the splice tray has already been loaded with fibers, be sure to carefully free up any
stored cable as you move away from the cabinet.
5.4 Breaking Out Side Entry Cables (from non-Flex-Frame Panels)
When using a stand-alone splice cabinet with side entry cables from other than CommScope
EHD/CHD panels in a Flex Frame application, use the following procedure referring to Figure 15.
1. Pull approximately a 134 in. (340 cm) length of the cable from the panel to a flat surface
near the cabinet.
2. Cut back the cable jacket to this location.
3. Cut a section of mesh tubing to a length of 80 in. (203.2 cm).
4. Slide the mesh tubing onto the cable from the bare ribbon end.
Figure 15. Side Entry Cable Breakout Exploded View
5. Secure the mesh tubing at the panel using vinyl tape.
5.5 Breaking Out Facility Cables
Table 4 lists the RIBCBOUT series breakout kits available for use with facility cables. These kits
include cable clamps, as indicated in the table.
All facility cables are broken out to the same dimensions (shown in Figure 16). These dimensions
allow approximately 6 feet (1.83 m) of working length for moving the splice tray to a convenient
Note: This procedure is only used with a stand alone splice cabinet and only when panels of a
type other than CommScope EHD/CHD in a Flex Frame application are used.
BREAKOUT LENGTH
134 IN. (340.36 CM)
80 IN.
(203.2 CM)
54 IN.
(137.16 CM)
CABLE CLAMP POINT ON PANEL
26909-A
12-FIBER RIBBONS (QTY 24)
RIBBON ROUTINGS
WITHIN PANEL
NOTE: SECTIONS SHOWN ARE
DIAGRAMMATIC, NOT
PROPORTIONAL
MESH TUBING

TC-96272-IP
© 2019 CommScope, Inc. . Page 15 of 20
work surface. When the splice tray is returned to the cabinet, the cable management features in
the cabinet are used to store slack as needed.
Use the following procedure to break out facility cables.
1. Identify and have on hand the breakout kit being used. Refer to the guidelines and
instructions provided with the kit.
2. Strip back the cable jacket to expose the internal fiber ribbons. Strip the cable at a
distance of 166 in. (421.6 cm) from the lead end of the cable as shown in Figure 16.
Figure 16. Facility Cable Breakout Exploded View
3. Prepare a piece of mesh tubing for each sub-unit of 288 fibers. Cut the pieces of mesh
sleeve to a length of 112.3 inches (284.5 cm).
4. Prior to insertion into the mesh, trim and tape together the fiber ends to prevent them
from snagging and breaking while being inserted.
5. Install a single piece of mesh tubing over each sub-unit of 288 fibers and slide the mesh
sleeve back to the cable jacket.
6. When all the sub-units have been routed to splice trays and the splice trays prepared,
wind a section of vinyl tape around at the meeting place of the cable jacket and the
mesh tubing to secure the mesh tubing to the cable jacket.
Note: For more on these kits, refer to TC-96271-IP (see “Related Publications” on page 2).
Table 4: Cable Clamp Kits
Breakout Kit
Catalog Number
Fiber
Count
Material
ID
Cable Clamp Kit
(Included)
RIBCBOUT-3/8-50-144/288/432/576 144-576 760244150 FEC-ACCCLMP01
RIBCBOUT-3/8-50-864/1152 864-1152 760244144 FEC-ACCCLMP01
RIBCBOUT-3/8-75-1728 1728 760244149 FEC-ACCCLMP01
RIBCBOUT-3/8-125-3456 3456 760244147 OSP-CLPFEC-XL-1
Note: When the mesh tubing is installed, there will be a length of 54 in. (137.2 cm) of exposed
ribbon fibers, as shown in the breakout diagram.
CABLE
CABLE CLAMP
26902-A
EXPOSED RIBBON FIBERS
END OF CABLE JACKET MESH TUBING
NOTE: SECTIONS SHOWN ARE
DIAGRAMMATIC, NOT
PROPORTIONAL ONE SUB-UNIT
(288 OR LESS FIBERS)
BREAKOUT LENGTH
166 IN. (421.6 CM)
112 IN.
(284.5 CM)
54 IN.
(137.2 CM)
POSITIONAL
(SLIDE CABLE
WITHIN CLAMP)

Page 16 of 20. © 2019 CommScope, Inc.
TC-96272-IP
5.6 Securing Facility Cables
Table 5 lists the CommScope cable clamp kits suggested for use with facility cables.
Use the following procedure to clamp facility cables.
1. Select and have on hand the appropriate cable clamp kit referring to Table 5.
2. Plan for spatial placement of the cables being installed. Typically, the cable being routed
to the lowest splice trays in the cabinet should be clamped on the rightmost position and
cables should be added going to the left, as shown in Figure 17.
3. Select the grommet that fits the cable and assemble the clamp components in the
cabinet, following the instructions provided in the kit. Figure 18 shows an example.
Table 5: Cable Clamp Kits
Cable Clamp Remarks
NG4-FLXACCSMCMP
(760242717) This is a stackable clamp with mounting pitch of 1.04 in. (2.64 cm) for cable diameters of 0.4 – 0.75 in. (1.0 - 1.90
cm). It uses a pair of Phillips head screws for attachment,
and is a good choice for lower count all-dielectric cables
as it is very compact and stackable
FEC-ACCCLMP01 This is a stackable clamp with a mounting pitch of 1.5 in
(3.81 cm) for cable diameters of 0.4 – 1.2 in. (1.0 - 3.05
cm). It uses a 3/8 in. male/female bolt for attachment, and
is a good choice for low or medium count all-dielectric or
armored cables as it is stackable and more robust than the
clamp above
OSP-CLPFEC-XL-1 This is a stackable clamp with a mounting pitch of 1.85 in.
(4.7 cm) for cable diameters of 0.4 – 1.5 in. (1.0 - 3.81
cm) It uses a 3/8 in. male/female bolt for attachment, and
is a good choice for high count all-dielectric or armored
cables. It is also the only option for some of the more
prevalent 3456-fiber cables on the market today
Note: RIBCBOUT kits include the appropriate cable clamp.

TC-96272-IP
© 2019 CommScope, Inc. . Page 17 of 20
Figure 17. Example of Facility Cable Clamping
Figure 18. Cable Clamp Kit Example (NG4-FLXACCSMCMP)
26914-A
YOKE
GROMMET
FASTENERS
GANG PLATE
CABLE

Page 18 of 20. © 2019 CommScope, Inc.
TC-96272-IP
5.7 Loading Splice Trays
The Flex Frame Splice Cabinet uses the FOST-ACC-D-TRAY-RR-288-KIT splice tray. Each
splice tray accommodates four splice chips, each with six mass fusion splices, for a capacity of
24 splices or 288 fibers per tray.
Panel stubs (or equivalent cables from non-Flex-Frame panels) come in from the left side of the
splice cabinet. Each panel stub goes to one splice tray. Facility cable sub-units come in from the
top of the splice cabinet. Each sub-unit (of 288 fibers maximum) goes to one splice tray.
Use the following procedure.
1. Once the number of facility cables to be brought into the cabinet is known, designate
cable positions from right to left in the cable entry area.
2. Unstrap the lowest splice tray in the bottom deck and remove it to a nearby flat working
surface.
3. Route the first panel stub (coming through the lowest entry portal) to the splice tray and
tie it down at the tie down point shown in Figure 19.
4. Wind the panel stub ribbons twice counterclockwise around the splice tray as shown.
5. Route the first sub-unit of the rightmost facility cable to the splice tray and tie it down at
the tie down point shown in Figure 19.
6. Wind the sub-unit ribbons twice clockwise around the splice tray as shown.
7. Return the splice tray to the splice deck.
8. Lift up the panel stub slack and hang it over the radius limiter just to the left of the top of
the splice deck.
9. Lift up the facility cable sub-unit slack and hang it over the cable management feature
just to the right of the top of the splice deck, forming a J pattern.
10. Place slack loops into cable routing clips on top and side of cabinet.
11. Continue to the second splice tray to do the same steps described above and then
continue on upward to the remaining splice trays.
12. When completed with the lower splice deck, repeat the same steps for the upper splice
deck using the analogous features in the top half of the cabinet.
Note: This procedure assumes that all splice trays are being loaded at the same time and are
being loaded from bottom to top within the cabinet. This is the most common but not the
only arrangement. If required, splice trays can be individually loaded.Any arrangement
is possible that results in an orderly routing of cables within the cabinet.
Note: Cables routed to the upper and lower splice decks should be separate from each other.

TC-96272-IP
© 2019 CommScope, Inc. . Page 19 of 20
Figure 19. Routing on Splice Tray
5.8 Performing Splices
A procedure for splicing is not provided in this document. Perform splices per local practice.
5.9 Changing Splice Trays
Any splice tray in the splice cabinet can be isolated for removal or for adding or removing splices
by allowing the splice trays in front of it to hang down while holding up the splice trays behind it
using the hook-and-loop strap.
26910-A
FROM
PANEL
STUB
ccw cw
FROM
FACILITY
CABLE
TIE
POINT
TIE
POINT

Page 20 of 20. © 2019 CommScope, Inc.
TC-96272-IP
6 Contact Information
• To find out more about CommScope®products, visit us on the web at
http://www.commscope.com
• For technical assistance, customer service, or to report any missing/damaged parts, go
to https://www.commscope.com/SupportCenter
• For information on product patents, go to http://www.cs-pat.com