CommScope ODF-SPLCAB-24 User manual

TC-96282-IP
Rev C, May 2020
commscope.com
User Manual
Universal Mount
Splice Cabinet
860657162 Rev C
© 2020 CommScope, Inc. Page 1 of 20
Contents
1 Product Description. . . . . . . . . . . . . . . . . . . . .2
1.1 General Description. . . . . . . . . . . . . . . . . . . . .2
1.2 Dimensions and Specifications . . . . . . . . . . . .4
1.3 Typical Application . . . . . . . . . . . . . . . . . . . . .5
2 Unpacking and Inspection . . . . . . . . . . . . . . . .6
3 Mounting the Cabinet . . . . . . . . . . . . . . . . . . .6
3.1 Mounting Options and Tools . . . . . . . . . . . . . .6
3.2 Mounting on Two-Post Equipment Rack . . . . .6
3.3 Mounting on Four-Post Frame . . . . . . . . . . . .8
3.4 Mounting Cabinet on Wall . . . . . . . . . . . . . . . .9
3.5 Grounding Cabinet . . . . . . . . . . . . . . . . . . . .11
4 Installing Cables and Loading Splice Trays .11
4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.2 Installing Splice Trays . . . . . . . . . . . . . . . . . .13
4.3 Removing Splice Trays . . . . . . . . . . . . . . . . .15
4.4 Breaking Out Facility Cables . . . . . . . . . . . . .15
4.5 Securing Facility Cables Inside Cabinet . . . .16
4.6 Securing Facility Cables Outside Cabinet . . .16
4.7 Loading Splice Trays. . . . . . . . . . . . . . . . . . .18
4.8 Performing Splices . . . . . . . . . . . . . . . . . . . .20
4.9 Changing Splice Trays . . . . . . . . . . . . . . . . .20
5 Related Publications . . . . . . . . . . . . . . . . . . .20
6 Contact Information . . . . . . . . . . . . . . . . . . . .20
Introduction
This user manual provides general information
and installation procedures for the Universal
Mount Splice Cabinet, shown at right in 24 tray
and 12 tray sizes with 19-inch mounting brack-
ets. Procedures include:
• Unpacking the cabinet
• Mounting the cabinet on a rack or 4-
post frame
• Mounting the cabinet on a wall
• Preparing cables for installation
• Installing cables
• Setting up splices
This manual also tells how to obtain technical
assistance.
24 Tray Cabinet
12 Tray Cabinet

Page 2 of 20. © 2019 CommScope, Inc.
TC-96282-IP
1 Product Description
1.1 General Description
The Universal Mount Splice Cabinet is a compact splice enclosure that provides a splicing
interface between facility cables. Facility cables are high-fiber-count cables containing rollable
ribbons, and of a type suitable for being routed indoors or outdoors. The splice cabinet is
available in two sizes: 24 trays (ODF-SPLCAB-24, shown in Figure 1), and 12 trays (ODF-
SPLCAB-12), which is analogous in features.
The splice cabinet mounts on a 19-inch or 23-inch equipment rack or four-post frame. It can also
be mounted on a wall. The 24 tray splice cabinet accommodates up to 24 splice trays, each with
a capacity of up to 24 rollable ribbon, mass fusion 12-fiber splices, for a total of up to 6912
spliced fibers per cabinet. The 12 tray splice cabinet has a capacity of 12 rollable ribbon, mass
fusion 12-fiber splices, for a total of up to 3456 spliced fibers per cabinet.
Figure 1. Interior Components of Universal Mount Splice Cabinet
(ODF-SPLCAB-24 shown)
27008-A
FRONT
OBLIQUE
VIEW
NORMAL
FRONT
OBLIQUE
VIEW
EXPLODED
SPLICE
TRAY
STACK OF
SPLICE
TRAYS
EXIT FOR
FACILITY
CABLES
(REF)
WALL
MOUNTING
BRACKET
(REF)
TRAY
HOLDER
BRACKET
(2X)
RADIUS
LIMITER
(6X)
ENTRY
FOR
FACILITY
CABLES
19-INCH
BRACKET
23-INCH
BRACKET
MOUNTING
BRACKETS

TC-96282-IP
© 2019 CommScope, Inc. . Page 3 of 20
Figure 1 shows the interior components of the splice cabinet including:
•Splice Tray -- is the FOST-ACC-D-TRAY-RR-288-KIT tray, which holds up to 24 mass
fusion 12-fiber splices for a total of up to 288 spliced fibers per splice tray.
•Stack of Splice Trays -- consists of up to 12 splice trays mounted on a tray-holder
bracket and held in place with a hook-and-loop strap. Unfastening the strap for a partic-
ular splice tray allows the tray to hang down for examination. A splice tray can be easily
removed to a work surface for fiber routing and splicing. The ODF-SPLCAB-24 has two
stacks of splice trays. The ODF-SPLCAB-12 has one stack of splice trays.
•Entry and Exit for Facility Cables -- are brush-lined openings through which facility
cables pass in and out of the cabinet.
•Radius Limiters -- are cable routing guides that are used to prevent cables from being
bent or kinked beyond the recommended minimum.
•Mounting Brackets -- provide 19-inch, 23-inch, and wall-mount options.
Figure 2 shows the top half of the 24 tray splice cabinet loaded with splice trays and cables. The
12 tray cabinet has essentially this same configuration alone.
Figure 2. Top Half of Splice Cabinet
(ODF-SPLCAB-24 shown)

Page 4 of 20. © 2019 CommScope, Inc.
TC-96282-IP
1.2 Dimensions and Specifications
Table 1 lists specifications for the two sizes of the splice cabinet. Figure 3 shows dimensions of
the 24 tray splice cabinet (ODF-SPLCAB-24). Figure 4 shows dimensions of the 12 tray splice
cabinet (ODF-SPLCAB-12).
Figure 3. 24 Tray Universal Mount Splice Cabinet (ODF-SPLCAB-24) Dimensions
Table 1: Splice Cabinet Specifications
Parameter ODF-SPLCAB-24 ODF-SPLCAB-12
Dimensions (H x W x
D)
68.5 in.(174 cm) x 17.84
in.(45.3 cm) x 11.54 in. (29.3
cm)
42.3 in.(107.4 cm) x 17.84
in.(45.3 cm) x 11.54 in. (29.3
cm)
Weight 52 lbs. (23.6 Kg) 32 lbs. (14.5 Kg)
Splice tray used FOST-ACC-D-TRAY-RR-288-
KIT (760243050)
FOST-ACC-D-TRAY-RR-288-
KIT (760243050)
Number of splice trays Up to 24 (2 stacks of 12 trays) Up to 12 total (1 stack of 12
trays)
Total number of
splices
Up to 6912 fiber splices (576
mass fusion 12-fiber splices)
Up to 3456 fiber splices (288
mass fusion 12-fiber splices)
Cable type Rollable ribbon Rollable ribbon
Fiber count capacity 6912 in, 6912 out 3456 in, 3456 out
Mounting options Can be mounted on a 19-inch
or 23-inch equipment rack or
4-post frame or on a wall
Can be mounted on a 19-inch
or 23-inch equipment rack or
4-post frame or on a wall
27009-A
68.5 IN.
(174 CM)
17.84 IN.
(48.30 CM)
11.54 IN.
(29.3 CM)

TC-96282-IP
© 2019 CommScope, Inc. . Page 5 of 20
Figure 4. 12 Tray Universal Mount Splice Cabinet (ODF-SPLCAB-12) Dimensions
1.3 Typical Application
Figure 5 shows a typical splice cabinet installation with facility cables in a 24 tray cabinet. The 12
tray cabinet is analogous in routing.
Figure 5. Universal Mount Splice Cabinet Application Example
(ODF-SPLCAB-24 shown)
27241-A
42.3 IN.
(107.4 CM)
17.84 IN.
(48.30 CM)
11.54 IN.
(29.3 CM)
97010-A
SPLICE CABINET
FACILITY CABLES
FACILITY CABLES
FACILITY CABLE
SUB-UNITS
(EACH GOES TO ONE
SPLICE TRAY)
FACILITY CABLE
SUB-UNITS
(EACH GOES TO ONE
SPLICE TRAY)
SPLICE
TRAYS
(12 IN EACH
STACK)
FAR OFF EQUIPMENTNEAR BY EQUIPMENT
NOTE: FACILITY
CABLES MUST BE
DIVISIBLE INTO
SUB-UNITS OF
288 FIBERS
OR LESS.
NOTE: THIS
DIAGRAM IS A
FUNCTIONAL
SCHEMATIC;
IT DOES NOT
SHOW CABLE
ROUTING IN
CABINET.

Page 6 of 20. © 2019 CommScope, Inc.
TC-96282-IP
2 Unpacking and Inspection
Use the following procedure to unpack and inspect the splice cabinet.
1. Inspect the exterior of the shipping container(s) for evidence of rough handling that may
have damaged the components in the container.
2. Unpack each container while carefully checking the contents for damage.
3. If damage is detected or if parts are missing, file a claim with the commercial carrier and
notify CommScope Support Center at http://www.commscope.com/SupportCenter
4. Save all shipping containers for use if the equipment requires shipment at a future date.
3 Mounting the Cabinet
3.1 Mounting Options and Tools
The Universal Mount Splice Cabinet can be mounted on a 19-inch or 23-inch equipment rack or
4-post frame. Alternatively, the cabinet can be mounted on a wall.
Mounting brackets must be separately ordered; for catalog numbers and Material IDs (MIDs),
refer to Table 2.
A Phillips #2 screwdriver is required in all installations. In addition, a level is required for wall
mounting.
3.2 Mounting on Two-Post Equipment Rack
The cabinet can be mounted on a 2-post 19-inch or 23-inch equipment rack using the mounting
brackets identified in Table 2 (separately ordered). The door must be fastened to the cabinet
when mounting the cabinet on an equipment rack.
Note: The 24 tray splice cabinet (ODF-SPLCAB-24) is shown in figures, Same process is
valid for the 12 tray splice cabinet (ODF-SPLCAB-12).
Note: If mounting the 12 tray splice cabinet (ODF-SPLCAB-12) to an equipment rack, only 4
of the 6 brackets are used.
Table 2: Mounting Bracket Kits
Kit Catalog Number MID Description
ODF-ACC-BRK-19 760245549 19-inch mounting brackets kit
ODF-ACC-BRK-23 760245550 23-inch mounting brackets kit
ODF-ACC-BRK-WM 760245551 Wall mounting brackets kit

TC-96282-IP
© 2019 CommScope, Inc. . Page 7 of 20
Use the following procedure.
1. Select and install the appropriate mounting brackets (Figure 6).
Figure 6. Two Post Installation Mounting Bracket Location
2. Fasten the splice cabinet to the rack with #12-24 screws and lock washers, as shown in
Figure 7.
Figure 7. Mounting the Splice Cabinet on an Equipment Rack
27012-A
MOUNTING
BRACKET (6X)
STAR
WASHER
MOUNTING
BRACKET
M4 SCREW
(8 mm LONG)
27011-A
MOUNTING
BRACKET (6X)

Page 8 of 20. © 2019 CommScope, Inc.
TC-96282-IP
3.3 Mounting on Four-Post Frame
The cabinet can be mounted on either a 19-inch or 23-inch four post frame using the mounting
brackets identified in Table 2 on page 6 (separately ordered). The door must be fastened to the
cabinet when mounting the cabinet on a four-post frame. Use the following procedure.
1. Select and install the appropriate mounting brackets (Figure 8).
Figure 8. Four Post Installation Mounting Bracket Location
2. Fasten splice cabinet to frame with #12-24 screws and lock washers (Figure 9).
Figure 9. Mounting the Splice Cabinet on a Four-Post Frame
27013 -A27013 -A MOUNTING
BRACKET (6X)
STAR
WASHER
MOUNTING
BRACKET
M4 SCREW
(8 mm LONG)
27014-A
MOUNTING
BRACKET (6X)

TC-96282-IP
© 2019 CommScope, Inc. . Page 9 of 20
3.4 Mounting Cabinet on Wall
Figure 10 shows the features of the wall mounting brackets.
Figure 10. Wall Mounting Bracket
Figure 11 shows the mounting dimensions for the two cabinet sizes.
Figure 11. Wall Mounting Dimensions
Use the following procedure.
Note: The 24 tray splice cabinet (ODF-SPLCAB-24) is shown in figures, Same process is
valid for the 12 tray splice cabinet (ODF-SPLCAB-12).
27016-A
18.0 IN. (45.72 CM)
3.5O IN.
(26.07 CM)
MOUNTING HOLE (14X)
DIAM. 0.265 IN. (0.673 CM)
0.75 IN.
(1.91 CM)
HORSESHOE HOLE
FOR LEVELING CABINET
#12-24 THREADED
PEMS (3X)
FOR MOUNTING CABINET
TO BRACKET
27017-A
55.00 IN.
(139.70 CM)
18.00 IN.
(45.72 CM)
12.03 IN.
(30.54 CM)
3.50 IN.
(8.89 CM)
68.79 IN.
(174.73 CM)
REF
27245-A
28.50 IN.
(72.39 CM)
18.00 IN.
(45.72 CM)
19.00 IN.
(48.26 CM) REF
12.02 IN.
(30.52 CM)
REF
3.50 IN.
(8.89 CM) 42.29 IN.
(107.42 CM)
REF
ODF-SPLCAB-12
ODF-SPLCAB-24

Page 10 of 20. © 2019 CommScope, Inc.
TC-96282-IP
1. Remove the door from the front of the splice cabinet.
2. On the rear side of the cabinet, install the mounting bracket on the cabinet using the
#12-24 screws provided. The top and bottom brackets are identical in design. Select
from the possible hole configurations drilled into the back wall of the cabinet.
3. Install a single support screw in the wall to temporarily hold the top mounting bracket
Place the screw in the top center of the desired cabinet location.
Figure 12. Mounting the Splice Cabinet on a Wall
4. Hang the cabinet on the wall by positioning the middle horseshoe opening (shown in
Figure 10 on Page 9) on the support screw just installed. Level the cabinet.
Note: Install the screw part way only.
27015-A
#12-24
SCREWS
& WASHERS
(6X)
UNVERSAL MOUNT
SPLICE CABINET
SPLICE
CABINET
DOOR
WALL
MOUNTING
BRACKET (2X)

TC-96282-IP
© 2019 CommScope, Inc. . Page 11 of 20
5. Secure the cabinet in a level position using appropriate wall mounting hardware on both
sides. Install the hardware from inside of the cabinet into the wall material.
3.5 Grounding Cabinet
Figure 13 shows the grounding location in the Universal Mount Splice Cabinet. Ground per local
practice.
Figure 13. Grounding Location
4 Installing Cables and Loading Splice Trays
4.1 Overview
Facility cables originate in other equipment, inside or outside of the building. Facility cables come
in from the top and are routed into the areas on the left and right of the splice tray stacks.
For purposes of cable routing within the cabinet, the cabinet divides into left and right sections.
The 24 tray cabinet has four sections: top right, top left, bottom right, and bottom left. The 12 tray
cabinet has left and right only.
Figure 14 on Page 12 shows the 24 tray cabinet top left and top right routing, which are the same
except that they are mirror images of one another. Bottom left and bottom right are routed in the
same way as top right and top left, except they are lower in the cabinet.
Typically each splice tray is loaded outside the cabinet on a work surface such as a table, then
the tray is returned to the cabinet and the cables are routed as shown.
Facility cables must be broken out to the dimensions indicated in Section 4.4 on page 15. This
may be done for all cables at the same time, before loading splice trays, or it may be done for the
associated cable as each splice tray is loaded.
Breakout kits are required for facility cables. The recommended RIBCBOUT kits are described in
TC-96271-IP (see “Section 5 on page 20).
97018-A
GROUND LOCATION
#10-32 THREADS
(FASTENERS
NOT PROVIDED)

Page 12 of 20. © 2019 CommScope, Inc.
TC-96282-IP
Figure 14. Cable Routing in Splice Cabinet
27021-A
31
32
38
6
7
34
5
9
1010
1212
1111
33

TC-96282-IP
© 2019 CommScope, Inc. . Page 13 of 20
4.2 Installing Splice Trays
The FOST-ACC-D-TRAY-RR-288-KIT trays used in the splice cabinet are shipped in separate
packages. Use the following procedure to install the splice trays in the cabinet.
1. Unpack the splice tray. Refer to Figure 15. There are two per box.
Figure 15. Unpacking the Splice Tray
2. Hold the splice tray vertically over the tray holder bracket, and insert the tray hinge into
the designated slot on the tray holder bracket. Lift the red tray support latch up to lower
the tray. Refer to Figure 16.
Figure 16. Inserting the Splice Tray in the Tray Holder Bracket

Page 14 of 20. © 2019 CommScope, Inc.
TC-96282-IP
3. Take the second splice tray and in a similar manner install it in the designated slot. Refer
to Figure 17.
Figure 17. Installing the Second Splice Tray
4. When done installing trays in a particular tray holder bracket, lift the trays up together
and fasten them in place using the hook-and-loop strap. Refer to Figure 18.
Figure 18. Securing Tray With Hook-and-Loop Strap

TC-96282-IP
© 2019 CommScope, Inc. . Page 15 of 20
4.3 Removing Splice Trays
After being installed, a splice tray can be removed. For example, this is done when moving the
splice tray to a work surface to perform splices.To remove a splice tray from the tray holder
bracket, use the following procedure.
1. Unfasten the hook-and-look strap.
2. Lift up the splice trays above the tray of interest and fasten them in place using the hook
and hook-and-loop strap.
3. Take hold of the tray of interest and pull the tray hinge out of the tray holder bracket.
4. If the splice tray has already been loaded with fibers, be sure to carefully free up any
stored cable as you move away from the cabinet.
4.4 Breaking Out Facility Cables
Table 3 lists the RIBCBOUT series breakout kits available for use with facility cables. All facility
cables are broken out to the same dimensions (shown in Figure 19). These dimensions allow
approximately 6 feet (1.83 m) of working length for moving the splice tray to a convenient work
surface. When the splice tray is returned to the cabinet, the cable management features in the
cabinet are used to store slack as needed.
Use the following procedure to break out facility cables.
1. Strip back the cable jacket to expose the internal fiber ribbons. Strip the cable at a dis-
tance of 166 in. (421.6 cm) from the lead end of the cable as shown in Figure 19.
Figure 19. Facility Cable Breakout Exploded View
Note: For more on these kits, refer to TC-96271-IP (see Section 5 on page 20).
Table 3: Cable Breakout Kits
Breakout Kit
Catalog Number
Fiber
Count Material ID
RIBCBOUT-3/8-50-144/288/432/576 144-576 760244150
RIBCBOUT-3/8-50-864/1152 864-1152 760244144
RIBCBOUT-3/8-75-1728 1728 760244149
RIBCBOUT-3/8-125-3456 3456 760244147
CABLE
27249-A
EXPOSED RIBBON FIBERS
TIE DOWN SECTION INSIDE CABINET MESH TUBING
NOTE: SECTIONS SHOWN
ARE DIAGRAMMATIC, NOT
PROPORTIONAL ONE SUB-UNIT
(288 OR LESS FIBERS)
BREAKOUT LENGTH
166 IN. (421.6 CM)
112 IN.
(284.5 CM)
54 IN.
(137.2 CM)
CABLE
INSIDE
CABINET
6-8 IN.

Page 16 of 20. © 2019 CommScope, Inc.
TC-96282-IP
2. Prepare a piece of mesh tubing for each sub-unit of fibers. Cut the pieces of mesh
sleeve to a length of 112 inches (284.cm).
3. Prior to insertion into the mesh, trim and tape together the fiber ends to prevent them
from snagging and breaking while being inserted.
4. Install a single piece of mesh tubing over each sub-unit of fibers and slide the mesh
sleeve back to the cable jacket.
5. As each single piece of mesh tubing is installed, wind a section of vinyl tape around the
cable sheath to secure the mesh tube to the sheath.
4.5 Securing Facility Cables Inside Cabinet
1. Use appropriate length cable ties.
2. Plan for spatial placement of the cables being installed. The cables that will populate the
upper splice trays should be located nearer the center of the cabinet. The cables that
will populate the lower splice trays should be located nearer the sidewalls of the cabinet.
Refer to Figure 20.
Figure 20. Example of Facility Cable Clamping
4.6 Securing Facility Cables Outside Cabinet
1. Mount the cable clamp bracket 6-8 inches above splice cabinet, as shown in Figure 21.
For the cable clamp bracket kit catalog number, refer to Tab l e 4.
Note: When the mesh tubing is installed, there will be a length of 54 in. (137.2 cm) of exposed
ribbon fibers, as shown in the breakout diagram.

TC-96282-IP
© 2019 CommScope, Inc. . Page 17 of 20
2. Use appropriately sized cable clamps (refer to Figure 21 and Ta ble 5).
3. Plan for spatial placement of cables being installed referring to Figure 21. The cables
that will populate the upper splice trays should be located nearer the center of the
bracket. The cables that will populate lower splice trays should be located nearer outer
edges of bracket.
Figure 21. Example of Facility Cable Clamping
Table 4: Cable Clamp Bracket Kit
Clamp Bracket Catalog Number Applications Material ID
ODF-ACCCBLCLMP-19 19” Rack Mounting,
Wall Mounting
760249074
Table 5: Cable Clamp Kits
Clamp Catalog
Number Size/Max Cable Outer Diameter QTY Material ID
NG4-FLXACCSMCMP Small / 0.4 - 0.75 in [10 - 19 mm] 1760242717
FEC-ACCCLMP01 Large / 0.4 - 1.2 in [10 - 30 mm] 1FEC-ACCCLMP01
OSP-CLPFEC-LG Large / 0.4 - 1.2 in [10 - 30 mm] 3 OSP-CLPFEC-LG
OSP-CLPFEC-XL-1 Extra Large / 1.25 - 1.5 in [32 - 38 mm] 1OSP-CLPFEC-XL-1
OSP-CLPFEC-XL Extra Large / 1.25 - 1.5 in [32 - 38 mm] 6 OSP-CLPFEC-XL
27243-A
EXTRA LARGE
STACKABLE
CLAMPS
LARGE
STACKABLE
CLAMPS
SMALL
STACKABLE
CLAMPS
CABLE
CLAMP
BRACKET

Page 18 of 20. © 2019 CommScope, Inc.
TC-96282-IP
4.7 Loading Splice Trays
The Universal Mount Splice Cabinet uses the FOST-ACC-D-TRAY-RR-288-KIT splice tray. Each
splice tray accommodates four splice chips, each with six 12-fiber mass fusion splices, for a
capacity of twenty four 12-fiber mass fusion splices (288 spliced fibers) per tray. Use the follow-
ing procedure.
1. Remove the splice cabinet cover.
2. Route the fiber cables to be spliced through the overhead cable pathway and to the
location of the splice cabinet. Ensure that there is a minimum of 15 feet of cable stub
available to work with from the point at which the cables will enter the top of the splice
cabinet.
3. Remove the cable access bar from the top of the splice cabinet by removing the two
Phillips head screws and place the bar and the screws aside for re-installation later.
Refer to Figure 22.
Figure 22. Removing Cable Access Bar
4. Break out each cable to be spliced as described in Section 4.4 on page 15 and in the
installation instructions for the mesh breakout kits (CommScope document number TC-
96271-IP). 144-fiber cables will have 12 ribbons (144-fibers) per mesh tube subunit. All
other cables will have 24 ribbons (288-fibers) per subunit. The cable sheath entry point
should fall between 6”-8” from the top of the splice cabinet once the cables have been
installed in the cabinet.
27023-A
CABLE
ACCESS
BAR

TC-96282-IP
© 2019 CommScope, Inc. . Page 19 of 20
5. Once all cables are broken out, load the cables into the cabinet through the cable
access slots and arrange them such that the cables that will populate the upper bank of
splice trays are located toward the center of the cabinet and the cables that will occupy
the lower bank of splice trays are located toward the sides of the cabinet.
6. Secure the cables to the cable tie-down bars as described in Section 4.5 on page 16
using plastic cable ties or, alternatively, waxed lacing cord.
7. Re-install the cable access bar to the top of the splice cabinet. Refer to Figure 22.
8. Unpackage the splice trays and adjust the four splice chips to the center of each tray to
allow for maximum space for routing the ribbons around the outside of the trays.
9. Locate the first group of fibers to be spliced (288 fibers from the left side of the cabinet
and 288 fibers from the right side of the cabinet) and secure the mesh sleeves to the
splice tray (Figure 23). The fibers from the left side of the cabinet are represented in red
and the fibers from the right side are represented in blue in this illustration.
Figure 23. Routing on Splice Tray
Note: The splice trays can be prepared for splicing and loaded into the cabinet in any order,
but the best results regarding the routing of the mesh sleeve material are achieved if the
trays are populated from bottom-to-top within the cabinet.
26910-A
FROM
PANEL
STUB
ccw cw
FROM
FACILITY
CABLE
TIE
POINT
TIE
POINT

Page 20 of 20. © 2019 CommScope, Inc.
TC-96282-IP
10. Route the bare fibers ribbons from the left side of the cabinet counterclockwise around
the splice tray and the ribbons from the right side of the cabinet clockwise as illustrated
in Figure 23.
11. If the fibers are to be spliced at this time, prepare the ribbons to the proper length and
splice according to local practice, then install the plastic cover on the splice tray. If
splicing is to be performed at a later time, install the plastic cover on the splice tray.
12. Install the splice tray into the proper position on the tray tower as described in Section
4.2 on page 13.
13. Route the mesh sleeve material for the splice tray into the routing path within the cabinet
as illustrated in Figure 14 on Page 12.
14. Repeat steps 9-14 for the remaining cables.
15. Re-install the splice cabinet cover.
4.8 Performing Splices
A procedure for splicing is not provided in this document. Perform splices per local practice.
4.9 Changing Splice Trays
Any splice tray in the splice cabinet can be isolated for removal or for adding or removing splices
by allowing the splice trays in front of it to hang down while holding up the splice trays behind it
using the hook-and-loop strap.
5 Related Publications
The following related publications are available at https://www.commscope.com/SupportCenter
•Ribbon Cable Breakout (RIBCBOUT) Kits User Manual (TC-96271-IP) -- provides a
high-level overview of and basic installation instructions for the CommScope RIBC-
BOUT (Ribbon Cable Breakout) series ribbon fiber cable breakout kits.
•Cable Clamp 19-Inch Bracket Kit Installation Drawing (660105113) -- contains instal-
lation instructions for the Cable Clamp 19-Inch Bracket Kit.
6 Contact Information
• To find out more about CommScope®products, visit us on the web at
http://www.commscope.com
• For technical assistance, customer service, or to report any missing/damaged parts, go
to https://www.commscope.com/SupportCenter
• For information on product patents, go to http://www.cs-pat.