CommScope NOVUX Compact Closure 100 Series User manual

Installation Instructions
page 1 / 13
© 2021 CommScope, Inc. All Rights Reserved
NOVUX™ Fiber Optic System
TC-1425-IP-PA
Rev. B, March 2021
http://www.commscope.com
CC 100 Patch Application
About this manual
This installation instructions document describes the installation steps of the patch application of the Compact
Closure 100 series. Installation steps in this document are limited to: splicing input of the connectors to the feeder
fibers, patching SC cables and patching LC cables.
Installation steps of the feeder and branch cables are explained in manual TC-1425-IP: CC 100 Basic Instructions.
The document starts with providing an overview of the tools required to perform the installation. Also warnings and
cautions are indicated, which should be observed before starting the product installation.
Images in this manual are for reference only and are subject to change.
General product information
Quantity drops installation method drops
SC/APC or SC/UPC up to 6 Pre-connectorized with and without transition, FIC, Xpress drop
LC/APC or LC/UPC up to 12 Pre-connectorized with and without transition, FIC
Overview organizer
1
2
3
4
1
23
5
1
23
6
1 Drop cable strain relief T-shapes
2 Locking features
3 Octopus™ gel seal
4 SC adapters
5 LC adapters
6 SC Xpress drop
860XXXXXX

Contents
Contents1 Abbreviations..................................................................................... 3
2 Tools.................................................................................................... 3
3 Warnings and Cautions..................................................................... 3
4 Splice feeder to input connector..................................................... 4
4.1 Splice feeder direct to input connector..................................................4
4.2 Splice feeder to factory installed splitter............................................... 5
4.3 Splice feeder and input connectors to field installable
splitter................................................................................................................. 5
5 Pre-connectorized cable....................................................................6
5.1 Install SC-connectorized cable...................................................................6
5.2 Install SC Xpres drop......................................................................................7
5.3 Install LC-connectorized cable................................................................... 8
6 Pre-connectorized cable with transition and FIC........................... 9
6.1 SC-connectorized cable with transition and FIC................................. 9
6.2 Install LC-connectorized cable with transition and FIC..................11
7 Trade-marks......................................................................................13
8 Contact information........................................................................ 13
page 2 / 13
© 2021 CommScope, Inc. All Rights Reserved

1 Abbreviations
CC: Compact Closure
FIC: Field Installable Connector
2 Tools
• Small side cutter or Cable Tie Gun (to cut excess cable tie)
• Fiber splice equipment and fiber cleaning tools
3 Warnings and Cautions
R
• Follow the installation instruction steps to ensure the performance of the closure. It is necessary to take
precautions and keep the working space clean to protect the closure sealing materials and splices.
• Exposure to laser radiation can seriously damage the retina of the eye. Do not look into the ends of any optical
fiber. Do not assume the laser power is turned off or that the fiber is disconnected at the other end. Looking into
the ends of any optical fiber is entirely at your own risk. A protective cap or hood MUST be immediately placed
over any radiating adapter or optical fiber connector to avoid the potential of dangerous amounts of radiation
exposure. This practice also prevents dirt particles from entering the connector and adapter.
• Fiber optic cables may be damaged if bent or curved to a radius that is less than the recommended minimum bend
radius. Always observe the recommended bend radius limit when installing fiber optic cables, subunits and patch
cords.
page 3 / 13
© 2021 CommScope, Inc. All Rights Reserved

4 Splice feeder to input connector
Prepare and install the feeder cable as explained in the CC 100 base instructions TC-1425-IP. Route the feeder fibers to
the rear tray. Note that the fibers can be routed directly to the rear splice tray or via the uncut fiber storage.
4.1 Splice feeder direct to input connector
1
2
x6
2
3
x6
1 The inputs of the connectors patched at the front are routed to the splice tray at the rear as shown in image above.
The 250μm fiber is already prepared.
Note: The pigtails and 250μm fibers have a color code to distinguish between the different ports. Advise prevailing
color code to select correct fiber.
2 Splice the input of the connectors to the feeder fibers (entering directly on the rear tray) by making a fusion splice:
make fusion splice per standard practice, store the splice protector in the splice protector holder and store over
length in loops on the tray.
3 If the feeder fibers come from the uncut storage zone, one of the fibers should be routed through the channel in
the middle of the tray before storing over length in loops on the tray.
Important: Make sure all fibers are properly positioned under the lips and avoid bulging of the fiber.
Note: The fiber guidance pen (situated on top of the loop storage basket) can be used to position all the fibers
under the lips.
page 4 / 13
© 2021 CommScope, Inc. All Rights Reserved

4.2 Splice feeder to factory installed splitter
1 A splitter is installed on the rear tray. The splitter outputs are already connected to the patch panel at the front side.
The input of the splitter is a 900µm fiber that should be stripped and spliced to a feeder fiber.
2 Splice the input of the splitter to the feeder fiber (entering directly on the rear tray) by making a fusion splice: make
fusion splice per standard practice, store the splice protector in the splice protector holder and store over length in
loops on the tray.
3 If the feeder fiber comes from the uncut storage zone, one of the fibers should be routed through the channel in
the middle of the tray before storing over length in loops on the tray.
Important: Make sure all fibers are properly positioned under the lips and avoid bulging of the fiber.
Note: The fiber guidance pen (situated on top of the loop storage basket) can be used to position all the fibers
under the lips.
4.3 Splice feeder and input connectors to field installable splitter
1
2
OUT
IN
3
OUT
IN
1 To install a field installable splitter, one splice protector holder should be removed first. Use the tip of the fiber
guidance pen to unlock the splice protector holder, then slide the splice protector downwards.
2 Slide the field installable splitter in one of the dove tails. Make sure the output of the splitter is oriented to the top.
3 Splitter installed in position 6.
page 5 / 13
© 2021 CommScope, Inc. All Rights Reserved

4 Splice the input of the splitter to the feeder fiber (entering directly on the rear tray) by making a fusion splice: make
fusion splice per standard practice, store the splice protector in the splice protector holder and store over length in
loops on the tray.
5 If the feeder fibers come from the uncut storage zone, one of the fibers should be routed through the channel in
the middle of the tray before to store over length in loops on the tray.
Important: Make sure all fibers are properly positioned under the lips and avoid bulging of the fiber
Note: The fiber guidance pen (situated on top of the loop storage basket) can be used to position all the fibers
under the lips.
6 Splice the output of the splitter to the connector input. For the SC application, store all 6 splice protectors in the
splice protector holder and store over length.
Note: Note that for the LC application, to connect all 12 drops, an extra splice protector holder should be installed
in position 4.
5 Pre-connectorized cable
5.1 Install SC-connectorized cable
1
2
3
1 Remove dust caps of the adapter port. Clean per standard practice.
2 Remove dust caps of the connector. Clean the connector per standard practice.
3 Position the connector in the correct orientation (rib facing forward as shown in figure above).
page 6 / 13
© 2021 CommScope, Inc. All Rights Reserved

4
5
6
4 Connect the SC-connectorized cable to its assigned port. Adapter ports are designated with the numbers 1-6. A
clicking sound is observed when the connector is properly seated.
5 All connectors installed.
6 Each cable should be routed to a separate entrance port. Dress each cable between the two ribs of the entrance
port below the adapter port.
Note: External cable fixation bracket is recommended to retain the cable outside the closure.
5.2 Install SC Xpres drop
The Xpres drops are a range of factory terminated drop cables with integrated strain relief features.
1
1
2
2
3
1 Remove dust caps of both the connector and the adapter port. Clean per standard practice. Swing the adapter port
upwards.
2 Position the connector in the correct orientation (rib facing to the right side as shown in figure above). Connect the
connectorized drop to its assigned port. Adapter ports are designated with the numbers 1-6. A clicking sound is
observed when the connector is properly seated.
3 Swing the adapter port with cable back in its original position.
page 7 / 13
© 2021 CommScope, Inc. All Rights Reserved

click
4
5
6
4 The metal ring just under the connector will click into the two snap hooks. The cable is hold between the two snap
hooks positioned lower on the organizer.
5 First Xpres drop cable installed.
6 All Xpres drop cables installed.
5.3 Install LC-connectorized cable
The separate cable retention kit TC-1467-IP (Cable retention: Dual cable ) must be used to install the LC-connectorized
cable in the CC 100 patch application.
Note: In case of a duplex LC-connectorized cable, refer to SC-connectorized cable installation.
1
2
3
1 Install a cable tie in one slot in the carrier at the bottom position and in one slot at the top position. Make sure the
heads are oriented correctly. Install the pre-connectorized cable on each level and fasten the cable ties but don't
tighten. The cable should move fluently up and then down.
Note: If only one cable to be installed, select the bottom position.
2 Slide the carrier into the slots of the organizer. Push the locking lip in the first slot backwards then slide the carrier
downwards. The locking lip returns into original position and the carrier is correctly seated. A clicking sound is
observed
3 Remove dust caps of both connector and adapter of the selected port. Clean the connector and adapter per
page 8 / 13
© 2021 CommScope, Inc. All Rights Reserved

standard practice. Position the connector in the correct orientation (clip facing forward as shown in figure above).
4
5
6
4 Slide the pre-connectorized cable forward and connect the connector to its assigned port. Adapter ports are
designated with the numbers 1-6 (two adapter ports per number, allowing to make 12 LC connections in total). A
clicking sound is observed when the connector is properly seated.
5 First two connectors installed.
6 All connectors installed.
Note: External cable fixation bracket is recommended to retain the cable outside the closure.
6 Pre-connectorized cable with transition and FIC
Important: Shown images in this section are routing suggestions provided for information purposes only. The
shape and fiber routing may differ depending on the cable and connector type. In case of a Field Installable Con-
nector (FIC) CommScope does not warrant the performance or compatibility of any third party or non-CommScope
products or components. Please verify all compatibility and performance requirements with the FIC supplier prior
to use a third party FIC.
6.1 SC-connectorized cable with transition and FIC
6.1.1 Using T-shapes integrated in organizer
6.1.1.1 Prepare drop cable
1 Cut the self-amalgamating silicone tape in half lengthwise. Cut 6,5 cm (2.56 Inches) of self-amalgamating silicone.
Attention: Make sure your hands are clean and degreased before preparing and installing the cables.
2 Position the cable on the organizer: The end of the sheath must be aligned with the rectangular rib (Figure 2). Make
a mark where the two ribs hold the cable and a second mark 2 cm (0.79 Inches) from the first.
3 Apply one of the strips of self-amalgamating silicone previously prepared between the two marks. Remove the
page 9 / 13
© 2021 CommScope, Inc. All Rights Reserved

protective paper from the self-amalgamating strip. Stretch the strip between 50% and 300% while wrapping the
strip around the cable. First apply a full turn around the cable, then continue to cover up to the second mark. Make
one turn at the end point and come back with the remaining tape.
6.1.1.2 Install drop cable
1
b
a
2Optional
1 Install 2 cable ties around the T-shape on the front of the organizer. Position the cable with the taped area on top
of the T-shape and secure the cable ties.
Note: Make sure to install the cable ties with the correct orientation (see figure above).
6.1.2 Install SC-connectorized cable with transition and FIC
Also the separate cable retention kits: TC-1466-IP (Cable retention: Aramid ) and TC-1468-IP (Cable retention: Jacket
(Mclip)) are suitable to be used to install the SC-connectorized cable with transition in the CC 100 patch application.
Pictures below shows an example with the M-clip.
1
2
3
1 If applicable install FIC per local practice. Follow the installation steps as described in TC-1468-IP to mount the
cable on the carrier. Slide the carrier into the slots of the organizer. Push the locking lip in the first slot backwards
then slide the carrier downwards. The locking lip returns into original position and the carrier is correctly seated. A
clicking sound is observed.
Note: Cable can also be installed with cable ties to the organizer as explained in previous section.
2 Remove dust caps of both the adapter port and the connector. Clean per standard practice. Position the connector
in the correct orientation (rib facing forward as shown in figure above).
3 Connect the SC-connectorized cable to its assigned port. Adapter ports are designated with the numbers 1-6. A
clicking sound is observed when the connector is properly seated.
page 10 / 13
© 2021 CommScope, Inc. All Rights Reserved

4
5
6
4 Coil the transition length and store it in loops in the organizer, under the lips and under the connectors. Make sure
not to store transition length in the area where the remaining carriers will be installed.
Important: Make sure the transition lengths are properly positioned under the lips and avoid bulging.
Important: Make sure to respect the minimum bend radius when storing the transition lengths.
Note: The fiber guidance pen (situated on top of the loop storage basket) can be used to position all the transition
lengths under the lips.
5 Transition length stored of cables installed in position 1-3.
6 Transition length stored of cables installed in position 1-6.
6.2 Install LC-connectorized cable with transition and FIC
The separate cable retention kit TC-1467-IP (Cable retention: Dual cable ) must be used to install the LC-connectorized
cable with transition in the CC 100 patch application.
1
2
3
1 If applicable, install the FIC per local practice. Follow the installation steps as described in TC-1467-IP to mount the
cables on the carrier. Slide the carrier into the slots of the organizer. Push the locking lip in the first slot backwards
then slide the carrier downwards. The locking lip returns into original position and the carrier is correctly seated. A
clicking sound is observed.
2 Remove dust caps of both connector and adapter of the selected port. Clean the connector and adapter per
standard practice. Position the connector in the correct orientation (clip facing forward as shown in figure above).
page 11 / 13
© 2021 CommScope, Inc. All Rights Reserved

3 Connect the connector to its assigned port. Adapter ports are designated with the numbers 1-6 (two adapter ports
per number, allowing to make 12 LC connections in total). A clicking sound is observed when the connector is
properly seated.
4
5
6
4 Coil the transition length and store it in loops in the organizer, under the lips and under the connectors. Make sure
not to store transition length in the area where the remaining carriers will be installed.
Important: Make sure the transition lengths are properly positioned under the lips and avoid bulging.
Important: Make sure to respect the minimum bend radius when storing the transition lengths.
Note: The fiber guidance pen (situated on top of the loop storage basket) can be used to position all the transition
lengths under the lips.
5 Transition length stored of cables installed in position 1-3.
6 Transition length stored of cables installed in position 1-6.
page 12 / 13
© 2021 CommScope, Inc. All Rights Reserved

7 Trade-marks
All trademarks identified by ® are registered trademarks in the US and may be registered in other countries. All third
party product names, trademarks and registered trademarks are property of their respective owners.
This document is for planning purposes only and is not intended to modify or supplement any specifications or
warranties relating to CommScope products or services. CommScope is committed to the highest standards of business
integrity and environmental sustainability, with a number of CommScope’s facilities across the globe certified in
accordance with international standards, including ISO 9001, TL 9000, and ISO 14001.
Further information regarding CommScope’s commitment can be found at: https://www.commscope.com/corporate-
responsibility-and-sustainability.
This product may be covered by one or more U.S. patents or their foreign equivalents. For patents, see www.cs-pat.com
8 Contact information
Visit our website or contact your local CommScope representative for more information.
For technical assistance, customer service, or to report any missing/damaged parts, visit us at: http://
www.commscope.com/SupportCenter
page 13 / 13
© 2021 CommScope, Inc. All Rights Reserved