Compak E6 OD User manual

ESSENTIAL ON DEMAND
E6 OD
E8 OD
E10 CONIC OD
E10 MASTER CONIC OD
coffee grinders
instructions manual

index
1. SAFETY MEASURES 1
2. DESCRIPTION 2
3. INSTRUCTIONS 3
4. IDENTIFICATION 3
5. TECHNICAL CHARACTERISTICS 4
6. EXTERNAL COMPONENTS 6
7. INSTALLATION 7
8. REGULATION 9
9. OPERATION 12
10. CONFIGURATION 14
11. CLEANING 18
12. MAINTENANCE 20
13. EC CONFORMITY 25

K06307 | v. 22/09/2014 | Ref. quality process 002/03 | ORIGINAL INSTRUCTIONS 1
1. SAFETY MEASURES
NOTE: The manufacturer will not be held responsible for any damages resulting from
improper use of the equipment, or for not following the safety measures as outlined
below.
Safety measures incorporated into our grinders:
• Specialscrewtomaintainthehopperxedinplace.
• Accessrestrictorinthegrindgroup.
Owners: Please pay careful attention with the following instructions:
• The grinder should be used exclusively for the function for which it was
designed:grindingwholebeancoffee.
• Donotusethisgrindertogrindothertypesoffoodproductssuchasdryfruit,
sugarorspices.
• The grinder should not be used by children or individuals with physical, or
mentallimitationsthatcouldresultinriskofinjuryormisuse.
• Anyotheruseofthemachinewillbeconsideredimproperanddangerous.
• Donotputliquidsincontactwithinternalorexternalpartsofthisgrinderwhile
ON or OFF,withtheexceptionofpartsexpresslyoutlinedinthe“CLEANING”
section of this manual. If liquids do come in contact with the grinder,
immediatelydisconnectelectricalconnectionandcarefullycleantheaffected
areas.Ifitisnecessarytoaccesstheinteriorpartsofthegrinder,contactyour
localserviceprofessional.
• Incaseofanydamagetopartsorcomponents,werecommendcontactingyour
local service professional to help with repair or replacement of such parts,
therebyguaranteeingthemaintenanceofthesecuritystandardsofthegrinder.
• Only an authorized distributor should replace the main power cable of the
grinder.

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v. 22/09/2014 | K06307
2
SOUNDDECIBELLEVEL
The level of sound emitted in different models is:
Sounddecibellevel With coffee
E6 OD 65 dB
E8 OD 70 dB
E10 CONIC OD 68 dB
E10 MASTER CONIC OD 68 dB
2. DESCRIPTION
Your new grinder has been designed using the most sophisticated technologies in
existence. The result is a product of high quality that offers the assurance of the best
results possible. Our products are manufactured by hand, one by one, following the
strictest quality requirements. In the manufacturing process, we use only the highest
quality materials (aluminum, stainless steel, etc.) especially designated for being in
contact with food stuff.
For the optimum functionality of the grinder models described in this user manual,
the maximum work cycles are as follows:
Model
Workingcycle
Function Stop
E6 OD
8 sec. 20 sec.
E8 OD
E10 CONIC OD
E10 MASTER CONIC OD

K06307 | v. 22/09/2014 | Ref. quality process 002/03 | ORIGINAL INSTRUCTIONS 3
3. INSTRUCTIONS
3.1. This manual is designed to provide the necessary information to correctly
install, use and maintain the grinder, as well as to highlight precautions for users to
keep in mind. To ensure the best operation of the coffee grinder, please follow the
instructions as outlined in this manual. This manual should be saved for the life of the
grinder, and should always be at the disposal of the operator.
3.2. This manual contains special terminology such as:
• Words in BOLD indicate important points or terminology.
• Numbers in parenthese after a word, indicate the location of this item in a parts
diagram.
Example: ( ) - Hopper lid
• Icons:
Information Atention
4. IDENTIFICATION
Inthegrinderinformationplaqueisthefollowingmanufacturing/product information.
NOTE: Themanufacturerreservestherighttochangecomponents/congurationsof
any model, according to the different geographic market demands.

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v. 22/09/2014 | K06307
4
5. TECHNICAL CHARACTERISTICS
5.1.Usage
The coffee grinders are intended for use on commercial premises and facilities where
ground coffee is required, or in small stores that sell coffee. The grinder must only be
used to grind coffee beans. Any use other than this will be considered improper and
dangerous.
NOTE: The manufacturer will not be held responsible for any damages resulting from
improper use of the equipment, or for not following the safety measures as outlined
below.
5.2.Technicaldata
Model 100V
50Hz
100V
60Hz
110V
60Hz
220V
60Hz
230V
50Hz
240V
50Hz
E6 OD
Electrical
power 750 810 860 735 730 840 (W)
Spin speed 1,250 1,540 1,600 1,600 1,325 1,330 rpm
E8 OD
Electrical
power 750 810 860 735 730 840 (W)
Spin speed 1,250 1,540 1,600 1,600 1,325 1,330 rpm
E10 CONIC
OD
Electrical
power 890 960 825 825 800 850 (W)
Spin speed 335 388 400 375 325 331 rpm
E10 MASTER
CONIC OD
Electrical
power 850 1,000 935 930 950 975 (W)
Spin speed 326 378 325 388 340 345 rpm

K06307 | v. 22/09/2014 | Ref. quality process 002/03 | ORIGINAL INSTRUCTIONS 5
Model
E6 OD E8 OD E10 CONIC
OD
E10 MASTER
CONIC OD
ØBurrs 2.5
64
3.3
83
2.65
Conic 68
2.65
Conic 68
in
mm
Production
50Hz*
25.90
11,77
34.22
15,55
28.87
13,12
33.59
15,27
lb/h
Kg/h
Production
60Hz*
28.87
13,12
38.23
17,37
33.00
15,00
39.04
17,74
lb/h
Kg/h
Dose time
50Hz
(7gr)*
2.14 1.62 1.92 1.65 Seconds
Dose time
60Hz
(7gr)*
1.92 1.45 1.68 1.42 Seconds
Hopper
capacity
3.74
1.700
3.74
1.700
3.74
1.700
3.74
1.700
lb
gr
Net weight 25.47
11,58
28.60
13,00
37.25
16,93
49.00
18,63
lb
Kg
Height
Width
Depth
25
8.46
15.74
635
215
400
25
8.46
15.74
635
215
400
25
8.46
15.74
635
215
400
28.14
8.46
15.74
715
215
400
in mm in mm in mm in mm
*Production is based on a medium-roasted coffee and an Espresso grind.

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v. 22/09/2014 | K06307
6
6. EXTERNAL COMPONENTS

K06307 | v. 22/09/2014 | Ref. quality process 002/03 | ORIGINAL INSTRUCTIONS 7
7. INSTALLATION
7.1.GeneralWarnings
The person installing the grinder should carefully read this instruction manual
before installation. The installation of this machine should be completed by
qualiedandauthorizedpersonnel,andallnormsofsafetyandsanitationshouldbe
followed.
7.2.ImportantWarnings
The operator of the grinder should be a responsible adult, and a never a minor
or person incapable of safely using such equipment. Whenusingthegrinder,
the following precautions should be followed:
• Nobarefeet.
• Nowethandsorfeet.
• Donotsubmergeinwater.
• Donotexposethegrindertosunorotheratmosphericconditions.
• Donotplaceanytypeofobjectinthecoffeeentranceorexitwhilethegrinder
isrunning.(Itshouldbekeptinmindthatthecuttingburrscontinueturningfor
acouplerevolutionsafterthegrinderispoweredoff).
• To disconnect the grinder, use the main power switch and never the power
cable,toavoidapossibleshortcircuit.

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v. 22/09/2014 | K06307
8
7.3.WheretoUse
The grinder should be installed on a at, stable surface. The minimum
dimensions of the work space should be as follows:
Model
E6 OD, E8 OD, E10 CONIC OD E10 MASTER CONIC OD
Height 25.78
655
28.93
735
in
mm
Width 9.25
235
9.25
235
in
mm
Depth 16.53
420
16.53
420
in
mm
7.4.GrinderInstallation
Before grinder installation, the following should be considered:
• The grinder information plaque data coincides with the electrical system on
site.
• Theelectricaloutletcoincideswiththegrinderplug.
• The electric power at the location of installation should meet the minimum
requiredtoproperlyrunthegrinder.
• Theinstallationsiteshouldhavetheproperelectricaloverloadprotections.
• Thegrindershouldbeproperlygroundedasspeciedbylocalcode.
NOTE: The grinder should be used in environments with mínimum temperature
of 77-86F and should not be installed in places (such as industrial kitchens) where
cleaning is done with direct water spray cleaning.

K06307 | v. 22/09/2014 | Ref. quality process 002/03 | ORIGINAL INSTRUCTIONS 9
8. REGULATION
8.1.Adjustingthelowerportaltersupport
Inordertoensuretheproperdistributionofgroundcoffeeintheportalter,while
supporting the portalter in a hands-free position during dosing, it is possible to
adjusttheheightofthelowerportaltersupport( ).
To do this adjustment operation:
1. Loosen the screw ( ) on the lower support ( ) by using the Allen Key included
with your grinder.
2. Adjustthesupportto thedesired heightusing theportalter asthe pointof
reference.
3. Tighten the screw ( ) with the Allen Key provided (Fig. 1).
NOTE: Iftheadjustmentisextreme(toohighortoolow),difcultiesinoperatingthe
dosis button might occur.
8.2.GrinderupSet
Place the hopper ( ) on the grind regulator ( ) and make sure the bean trap ( )
is in the closed position. Lock the hopper ( )inplaceusingaatheadscrewdriver
to gently tighten the hopper security screw making it match to the hole at the bean
hopper collar ( ) (Fig. 2).
Remove the hopper lid ( ),llthehopperwithcoffee( ), and replace the lid on the
hopper ( ) (Fig. 3).

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v. 22/09/2014 | K06307
10
Plug in the grinder, and place the main power switch ( ) AUTOMATIC–OFF–MANUAL
/ I-OFF-II to position AUTOMATIC / I and open the bean trap ( ) to allow coffee to
pass into the grind chamber.
8.3.Grindadjustmentsystem
8.3.1.Parallelmicrometricalsystem
Rotate the grind regulator ( ) until reaching the grind level desired.
Rotating the grind regulator clockwise will result in a courser grind; turning the
regulatorcounterclockwisewillresultinanergrinder*(Fig. 4).
Onceyoureachthedesiredgrindingpoint,youcanxthegrindingregulation( )
using the regulation break ( ) (Fig. 5).
*NOTE: Changing grind settings must be done when the grinder is on and burrs are in motion.
Not doing this suposes that the burrs will gunk up and cleaning will be required.

K06307 | v. 22/09/2014 | Ref. quality process 002/03 | ORIGINAL INSTRUCTIONS 11
* Itisrecommendedthatthemotorberunningwhenadjustingtonergrindsetting.
This helps to avoid jamming the burrs, which can occur when coffee beans are in the
grindchamber,andthegrindregulatorisadjustedtowardsne.
8.3.2.Steppedgrindadjustment(optional)
In the stepped adjustment versions, the positions on the grind regulator are limited
by“steps”thataredenedbytheholeandpinpoints(Fig. 6).
The instructions detailed in section 8.3.1. on adjusting the regulator should be
followed, while at the same time, pulling the brake post ( ) (Fig. 6) up to release the
locking action of the post.
NOTE: If the output is very slow, it could mean that the coffee is being ground too
ne.Iftheoutputisveryfast,itcouldmeanthatthecoffeeisbeinggroundtoocoarse.
A perfect espresso grind is found when the grind point gives an infusion of 25 ml of
coffee in 25 seconds using 7 grams of ground coffee.

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v. 22/09/2014 | K06307
12
9. OPERATION
9.1.Generalswitch
The general switch ( ) has 3 positions of use, I–0–II for E6 ESSENTIAL ON DEMAND
and E8 ESSENTIAL ON DEMAND (Fig. 7.1.) and AUTOMATIC-OFF-MANUAL for E10
CONIC ESSENTIAL ON DEMAND and E10 MASTER CONIC ESSENTIAL ON DEMAND
(Fig. 7.2.).
E6 OD,
E8 OD
E10 CONIC OD,
E10 MASTER
CONIC OD
Electrical functions I AUTOMATIC
Off 0 OFF
Manual mode. Security sistem that allows
using the grinder in case of the supply plate or
keypad failure.
II MANUAL
9.2.Utilization
Through the program menu (section 10.3.), it is possible to select two distinct
functional modes: AUTOMATIC MODE and PRESLECT MODE.

K06307 | v. 22/09/2014 | Ref. quality process 002/03 | ORIGINAL INSTRUCTIONS 13
9.3.AutomaticMode
Selection of doses by lower pulse button ( ) (2 doses / 3 doses version):
• 1 ACTIVATION OF LOWER PULSE BUTTON ( ) -> 1 DOSE
• 2 ACTIVATIONS OF LOWER PULSE BUTTON ( ) -> 2 DOSES
• 3 ACTIVATIONS OF LOWER PULSE BUTTON ( ) -> 3 DOSES*
*Availableonlyforthe3dosesoftwareoption.
When beginning the grind cycle, the LCD screen ( ) will show current dose mode
(single,double,triple)accompaniedbythetimeconguredforthedose,whichwill
countdowntozeroasthedosecyclesthrough.
Once the grind cycle is initiated, it can be paused by pressing the activation button
(). The cycle will pause, and will complete the timed grind cycle as long as the
lower activation button is pressed again within 10 seconds. After 10 seconds of
inactivity, the grind cycle will reset to the complete cycle time.
9.4.PreselectMode
In the PRESELECT mode, a pre-programmed single, double or triple dose can be set
by simple pressing the corresponding icon on the LCD screen ( ).
The preselection of a single, double or triple dose will remain active until it is changed
bypressingoneofthethreenumberedpreselecticons.Thispreselectionisreected
on the LCD screen ( ) with the icon of the active selection in the secondary color,
and the rest of the icons in the principle color.
Dispensing the preselected dose by pressing the lower pulse button ( ) one time.
When the grinding cycle begins, a timer countdown will begin on the LCD screen ( ),
whichwillcountdownthetimeddosecycletozero.
Once the grind cycle is initiated, it can be paused by pressing the lower activation
button ( ). The cycle will pause, and will complete the timed grind cycle as long as
the lower activation button is pressed again within 10 seconds. After 10 seconds of
inactivity, the grind cycle will reset to the complete cycle time.

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v. 22/09/2014 | K06307
14
9.5.Tamper
9.5.1.FixedTamper(Optional)
Positiontheportalterbelowthetamper( ) and push up to tamp the ground coffee
(Fig. 8).
10. CONFIGURATION
10.1.DisplayIconGuide
Access to menu.
Value or selection aproval.
Return.
Up shift in menu.
Decrease value.
Down shift in menu.
Increase value.
10.2.GrindTimeCongurations
Thegrind timescan be congured for theAutomatic andPreselect modes.When
modifyingthegrindtimeforeithermode,thetimewillbereectedinbothmodes
simultaneously.
To modify the time of one dose, press the time of the respective dose numerical
icon ( , or ) on the touch screen twice (double tap), followed immediately (2
seconds or less) by pressing the . button.

K06307 | v. 22/09/2014 | Ref. quality process 002/03 | ORIGINAL INSTRUCTIONS 15
Automatically the icon of the desired dose icon and the icon will change to active
colorandthefourtimenumberswillthenbegintoash.
There are two ways to modify the time:
• Press the icons or on the LCD screen and the time will increase, and press
the icon to decrease the time.
• Also, the time can be changed by using the lower dose button ( ) or the icon
() found on the LCD screen ( ). If any of these options are pressed, the grinder
will begin to run and the time, starting at zero, will increase until the chosen
button is released.
10.3.Changingthecongurationmenu
Toenterthecongurationmenú,pressthe icon. Once in the menu, use the buttons
(, or )totogglethroughthemenuoptions,andconrm/choosethedesired
option with the button. Press the icon to return to the previous option.
Toexitthemenú,pressthearrowbuttonuntilthemainmenuscreenisreached,or
simply press nothing for 10 seconds and the menu will reset to the beginning.
Through the conguration menu, it is possible to modify the following grinder
features:

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v. 22/09/2014 | K06307
16
MENU SET UP
LANGUAGESETUP
ENGLISH ENGLISH ACTIVE
SPANISH ESPAÑOL ACTIVO
FRENCH FRANÇAIS ACTIVE
GERMANY DEUTSCHE AKTIV
ITALIAN ITALIANO ATTIVO
PORTUGUESE PORTUGUESE ACTIVA
VIEWUSAGEDATA
NUMBER OF SINGLE SERVINGS
ABSOLUTE COFFEE COUNTER
N. COFFEE DOSES 1 dd/mm/aa 0000000
N. COFFEE DOSES 2 dd/mm/aa 0000000
N. COFFEE DOSES 3*dd/mm/aa 0000000
RELATIVE COFFEE COUNTER
N. COFFEE DOSES 1 dd/mm/aa 0000000
N. COFFEE DOSES 2 dd/mm/aa 0000000
N. COFFEE DOSES 3*dd/mm/aa 0000000
BURR WARE DATA ALARM 00000 Kg
GROUND 000000 Kg
SETTINGS
CONFIGURATION
OPERATING MODE
(WORKING MODE SETTINGS)
AUTOMATIC MODE AUTOMATIC MODE ON
PRESELECT MODE PRESELECT MODE ON
PASSWORD SET UP
(Limitates access to menu)
PASSWORD ON PASSWORD PROTECTION ON
PASSWORD OFF PASSWORD PROTECTION OFF
PASSWORD SET UP CURRENT PASSWORD 0000
(ENTER) NEW PASSWORD 0000 PASSWORD SAVED
WRONG PASSWORD
TIME SET UP/
DATE SET UP
TIME SETTINGS CURRENT TIME hh:mm:ss TIME SAVED
DATE SETTINGS
FORMAT dd/mm/aa NEW FORMAT SAVED
FORMAT mm/dd/aa NEW FORMAT SAVED
DATE SET UP CURRENT DATE dd/mm/aa NEW DATE SAVED
SOUND SET UP
ACTIVE SOUND SOUND ON
DEACTIVE SOUND SOUND OFF
BURRCHANGEALARM**
(Activates display at beginning/ending
of service)
BURR CHANGE ALARM ON ALARM ON CHANGE BURRS!
BURR CHANGE ALARM OFF ALARM OFF
RESET BURR CHANGE ALARM ALARM RESET
BURR CHANGE ALARM SET UP DOSE WEIGHT 2 00,00 gr Kg BURR CHANGE 00000 Kg ALARM SAVED
RESETRELATIVECOFFEE
COUNTER
RESET RELATIVE COFFEE (SERVINGS)
COUNTER
*NUM.COFFEEDOSE3: Only available for units with 3 dosing times. **BURRCHANGEALARM:Warningmessage.Weightsetbytheuserasgroundresultfortime2(Dose2),isthereferencetakenbythesoftwaretogetcoffeeproductiongures.

K06307 | v. 22/09/2014 | Ref. quality process 002/03 | ORIGINAL INSTRUCTIONS 17
MENU SET UP
LANGUAGESETUP
ENGLISH ENGLISH ACTIVE
SPANISH ESPAÑOL ACTIVO
FRENCH FRANÇAIS ACTIVE
GERMANY DEUTSCHE AKTIV
ITALIAN ITALIANO ATTIVO
PORTUGUESE PORTUGUESE ACTIVA
VIEWUSAGEDATA
NUMBER OF SINGLE SERVINGS
ABSOLUTE COFFEE COUNTER
N. COFFEE DOSES 1 dd/mm/aa 0000000
N. COFFEE DOSES 2 dd/mm/aa 0000000
N. COFFEE DOSES 3*dd/mm/aa 0000000
RELATIVE COFFEE COUNTER
N. COFFEE DOSES 1 dd/mm/aa 0000000
N. COFFEE DOSES 2 dd/mm/aa 0000000
N. COFFEE DOSES 3*dd/mm/aa 0000000
BURR WARE DATA ALARM 00000 Kg
GROUND 000000 Kg
SETTINGS
CONFIGURATION
OPERATING MODE
(WORKING MODE SETTINGS)
AUTOMATIC MODE AUTOMATIC MODE ON
PRESELECT MODE PRESELECT MODE ON
PASSWORD SET UP
(Limitates access to menu)
PASSWORD ON PASSWORD PROTECTION ON
PASSWORD OFF PASSWORD PROTECTION OFF
PASSWORD SET UP CURRENT PASSWORD 0000
(ENTER) NEW PASSWORD 0000 PASSWORD SAVED
WRONG PASSWORD
TIME SET UP/
DATE SET UP
TIME SETTINGS CURRENT TIME hh:mm:ss TIME SAVED
DATE SETTINGS
FORMAT dd/mm/aa NEW FORMAT SAVED
FORMAT mm/dd/aa NEW FORMAT SAVED
DATE SET UP CURRENT DATE dd/mm/aa NEW DATE SAVED
SOUND SET UP
ACTIVE SOUND SOUND ON
DEACTIVE SOUND SOUND OFF
BURRCHANGEALARM**
(Activates display at beginning/ending
of service)
BURR CHANGE ALARM ON ALARM ON CHANGE BURRS!
BURR CHANGE ALARM OFF ALARM OFF
RESET BURR CHANGE ALARM ALARM RESET
BURR CHANGE ALARM SET UP DOSE WEIGHT 2 00,00 gr Kg BURR CHANGE 00000 Kg ALARM SAVED
RESETRELATIVECOFFEE
COUNTER
RESET RELATIVE COFFEE (SERVINGS)
COUNTER
*NUM.COFFEEDOSE3: Only available for units with 3 dosing times. **BURRCHANGEALARM:Warningmessage.Weightsetbytheuserasgroundresultfortime2(Dose2),isthereferencetakenbythesoftwaretogetcoffeeproductiongures.

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v. 22/09/2014 | K06307
18
11. CLEANING
11.1.Generalcleaning
To ensure that the grinder functions properly, and produces the highest quality grind
possible, the parts that come into contact with coffee should cleaned periodically.
General Cleaning guidelines as follows:
• Always turn the main power switch to the off position ( ).
• Unplug the machine from the power source.
• Do not submerge the grinder in water or use power washing devises.
11.2.Beanhoppercleaning
In order to properly clean the bean hopper ( ),rstemptyoutallremainingbeans
and fragments.
Toremovethehopper,rstclosethebeantrap( ), and then loosen the hopper lock
screw ( ) and lift the hopper straight up.
Clean the hopper ( ) with a moist soft cloth or with a small amount of water and
soap to eliminate any oily residue from the beans.
Replace the bean hopper ( ) following the same steps as the removal process, but
in reverse.
11.3.Cleaningthecoffeeexitchute
It is very important to maintain the exit chute ( ) clean of coffee in order to assure
the consistency of the dosis and the continued functioning of the grinder.
A tubular chute brush should be used for this cleaning process. Simply inset the
brush up into the mouth of the exit chute ( ) (Fig. 9), carefully twisting the brush to
remove any remaining grounds in the chute.
Caution: Do not force brush too high up the chute as there is a fragile rubber dosis
curtain at the upper end of the chute. Damage to the rubber curtain can result in less
precise dosing. Also, the dosis button ( )alongwiththeupperandlowerportalter
holders ( , ) should be wiped periodically to prevent build up of coffee grounds
and oils it is recommending to clean the out.