Connect Tech CCG010 User manual

1
COM Express®Type 10 Mini Carrier
CCG010 / CCG020
Connect Tech Inc. Tel: [phone]
42 Arrow Road Toll: 800-426-8979 (North America only)
Guelph, Ontario Fax: [phone]
N1K 1S6 Email: [e-mail]
www.connecttech.com [e-mail]
CTIM-00120 Revision 0.12 2018-01-05

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 2 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
Table of Contents
Table of Contents...................................................................................................................................1
Preface...................................................................................................................................................4
Disclaimer .......................................................................................................................................................4
Customer Support Overview...........................................................................................................................4
Contact Information ........................................................................................................................................4
Limited Product Warranty...............................................................................................................................5
Copyright Notice.............................................................................................................................................5
Trademark Acknowledgment..........................................................................................................................5
ESD Warning ..................................................................................................................................................6
Revision History ....................................................................................................................................6
Introduction...........................................................................................................................................7
Product Features and Specifications ......................................................................................................8
Product Overview..................................................................................................................................9
Block Diagrams...............................................................................................................................................9
CCG010 Block Diagram ......................................................................................................................9
CCG020 Block Diagram ......................................................................................................................9
Connector Locations .....................................................................................................................................10
CCG010 Top View.............................................................................................................................10
CCG010 Bottom View .......................................................................................................................10
CCG020 Top View.............................................................................................................................11
CCG020 Bottom View .......................................................................................................................11
Connector Summary............................................................................................................................12
Jumper Summary................................................................................................................................12
Detailed Feature Pinouts and Functional Descriptions .........................................................................13
COM Express Module...................................................................................................................................13
Display Outputs.............................................................................................................................................14
LVDS Video Connector .....................................................................................................................14
LVDS Backlight Power Connector ....................................................................................................15
DisplayPort ++ (DDI) Video Connector.............................................................................................16
HDMI / DVI / VGA............................................................................................................................17
USB...............................................................................................................................................................18
USB 2.0 Port Connectors....................................................................................................................18
USB 3.0/2.0 Port Connectors..............................................................................................................19
10/100/1000 Ethernet (GBE) Connector.......................................................................................................20
Software Support for the Intel 82574 .................................................................................................20
Serial .............................................................................................................................................................21
RS-232/485 Connector .......................................................................................................................21
RS-232/485 Jumper Configuration.....................................................................................................22
J1 –RS-232/485 Jumper Block .........................................................................................................................................22
Serial Line Modes.............................................................................................................................................................. 22
Examples ...........................................................................................................................................................................22
Audio.............................................................................................................................................................23
Software Support for the CS4207.......................................................................................................23
External SATA (CCG010 Only) ...................................................................................................................24
microSD Card Connector ..............................................................................................................................25
mini PCIe & mSATA Slots...........................................................................................................................26
Dual Function mini PCIe mSATA Slots.............................................................................................26
Half and Full Length mini PCIe / mSATA module Installation.........................................................27

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 3 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
Standoff and Screw Assembly Details................................................................................................27
CCG020 –External Hard Drive Installation.......................................................................................28
mini pcie / mSATA Connector Pinout................................................................................................28
System Miscellaneous...................................................................................................................................30
System Connector...............................................................................................................................30
J2 –System Jumper Block..................................................................................................................30
Input Power & Control..................................................................................................................................31
RTC Battery ..................................................................................................................................................31
Typical Hardware Installation Procedure ............................................................................................32
On-board Indicator LEDs (CCG010 Only) ...................................................................................................32
Power Consumption and Thermals......................................................................................................33
Current Consumption....................................................................................................................................33
Thermal Properties ........................................................................................................................................33
Mechanical Drawings & Models ..........................................................................................................35
Cable Kits............................................................................................................................................37
CCG010 Cable Kit - CKG014 –“Full” Cable Kit ........................................................................................37
CCG010 Cable Kit - CKG015 –“Starter” Cable Kit ....................................................................................37
CCG020 Cable Kit - CKG035 –“Full” Cable Kit ........................................................................................38
CCG020 Cable Kit - CKG058 –“Starter” Cable Kit ....................................................................................38
Appendix A –COM Express Signal/Pinout Connection Details............................................................39

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 4 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
Preface
Disclaimer
The information contained within this user’s guide, including but not limited to any product specification, is
subject to change without notice.
Connect Tech assumes no liability for any damages incurred directly or indirectly from any technical or
typographical errors or omissions contained herein or for discrepancies between the product and the user’s
guide.
Customer Support Overview
If you experience difficulties after reading the manual and/or using the product, contact the Connect Tech
reseller from which you purchased the product. In most cases the reseller can help you with product installation
and difficulties. In the event that the reseller is unable to resolve your problem, our highly qualified support
staff can assist you. Our support section is available 24 hours a day, 7 days a week on our website at:
www.connecttech.com/sub/support/support.asp. See the contact information section below for more
information on how to contact us directly. Our technical support is always free.
Contact Information
Mail/Courier
Connect Tech Inc.
Technical Support
42 Arrow Road
Guelph, Ontario
Canada N1K 1S6
Email/Internet
[email protected]m
[email protected]m
www.connecttech.com
Note:
Please go to the Download Zone or the Knowledge Database in the Support Center on the Connect Tech
website for product manuals, installation guides, device driver software and technical tips.
Submit your technical support questions to our customer support engineers via the Support Center on the
Connect Tech website.
Telephone/Facsimile
Technical Support representatives are ready to answer your call Monday through Friday, from 8:30 a.m. to
5:00 p.m. Eastern Standard Time. Our numbers for calls are:
Toll Free: 800-426-8979 (North America only)
Telephone: [phone] (Live assistance available 8:30 a.m. to 5:00 p.m. EST,
Monday to Friday)
Facsimile: 519-836-4878 (on-line 24 hours)

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 5 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
Limited Product Warranty
Connect Tech Inc. provides a two-year Warranty for the COM Express®Type 10 Mini Carrier Board. Should
this product, in Connect Tech Inc.'s opinion, fail to be in good working order during the warranty period,
Connect Tech Inc. will, at its option, repair or replace this product at no charge, provided that the product has
not been subjected to abuse, misuse, accident, disaster or non-Connect Tech Inc. authorized modification or
repair.
You may obtain warranty service by delivering this product to an authorized Connect Tech Inc. business
partner or to Connect Tech Inc. along with proof of purchase. Product returned to Connect Tech Inc. must be
pre-authorized by Connect Tech Inc. with an RMA (Return Material Authorization) number marked on the
outside of the package and sent prepaid, insured and packaged for safe shipment. Connect Tech Inc. will
return this product by prepaid ground shipment service.
The Connect Tech Inc. Limited Warranty is only valid over the serviceable life of the product. This is defined
as the period during which all components are available. Should the product prove to be irreparable, Connect
Tech Inc. reserves the right to substitute an equivalent product if available or to retract the Warranty if no
replacement is available.
The above warranty is the only warranty authorized by Connect Tech Inc. Under no circumstances will
Connect Tech Inc. be liable in any way for any damages, including any lost profits, lost savings or other
incidental or consequential damages arising out of the use of, or inability to use, such product.
Copyright Notice
The information contained in this document is subject to change without notice. Connect Tech Inc. shall not
be liable for errors contained herein or for incidental consequential damages in connection with the furnishing,
performance, or use of this material. This document contains proprietary information that is protected by
copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to
another language without the prior written consent of Connect Tech, Inc.
Copyright

2016 by Connect Tech, Inc.
Trademark Acknowledgment
Connect Tech, Inc. acknowledges all trademarks, registered trademarks and/or copyrights referred to in this
document as the property of their respective owners.
Not listing all possible trademarks or copyright acknowledgments does not constitute a lack of
acknowledgment to the rightful owners of the trademarks and copyrights mentioned in this document.

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 6 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
ESD Warning
Electronic components and circuits are sensitive to
ElectroStatic Discharge (ESD). When handling any circuit
board assemblies including Connect Tech COM Express
carrier assemblies, it is recommended that ESD safety
precautions be observed. ESD safe best practices include,
but are not limited to:
Leaving circuit boards in their antistatic packaging
until they are ready to be installed.
Using a grounded wrist strap when handling circuit
boards, at a minimum you should touch a grounded
metal object to dissipate any static charge that may be
present on you.
Only handling circuit boards in ESD safe areas, which
may include ESD floor and table mats, wrist strap
stations and ESD safe lab coats.
Avoiding handling circuit boards in carpeted areas.
Try to handle the board by the edges, avoiding contact
with components.
Revision History
Revision
Date
Changes
0.00
2013-08-06
Original
0.01
2015-02-25
Pinout Updates
0.02
2015-09-09
Added CCG020 Information
0.03
2015-09-21
Corrected RS-232/RS-485 Pinout/Jumper Info
0.04
2015-10-06
Corrected Ethernet Naming Error and Fixed Naming Consistency
0.05
2015-10-15
Added CCG020 Mechanical Drawings
0.06
2016-06-07
Revised Warranty Policy
0.07
2016-06-08
Added Pinout, Corrected Connector Summary
0.08
2016-11-11
Updated images
0.09
2016-12-02
Update format, updated RTC battery information
0.10
2017-06-21
Update format
0.11
2017-07-13
Added cable drawing links, removed drawings from doc
0.12
2018-01-05
Revised cable information

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 7 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
Introduction
Connect Tech’s COM Express® Type 10 Mini Carrier Board is an extremely small carrier board featuring
rugged, locking connectors and offers the ultimate durability.
COM Express® Type 10 Mini Carrier Board is ideal for space constrained applications, harsh environments,
demanding conditions and supports extended temperature ranges of -40°C to +85°C.

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 8 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
Product Features and Specifications
Specifications
Compatibility
COM Express®Type 10 Mini Modules
PICMG COM Express® COM.0 R2.1
Mini PCIe Expansion
2 x half size cards OR 1 x full length card
Both sockets have PCIe and USB signaling, one socket also can be
configured as mSATA.
Storage
CCG010: 1 x mSATA, 1 x 1 Ext RA 7-pin Connector
CCG020: 1 x mSATA
USB
CCG010: 8 x USB 2.0 Ports (6 to connectors, 2 to miniPCIe)
CCG020: 2 x USB 3.0 Ports (Only if supported by COM Express Module)
6 x USB 2.0 Ports (2 to USB 3.0 connector, 2 to USB 2.0 connector, 2 to
miniPCIe)
Network
2 x Gigabit Ethernet (10/10/1000) Ports:
1 from COM Express
1 from on-board Intel 82574I PHY/Controller
GPIO
8-bit GPIO
Display
1 x DisplayPort++ (DDI) interface:
Can be used for DisplayPort, HDMI, DVI or VGA
1 x LVDS interface (18-bit, 3 data pairs)
Audio
HD Audio (Cirrus Logic CS4207 codec)
1 x stereo input
1 x stereo output
Serial
2 x RS-232/422/485 hardware selectable ports
Misc External Interfaces
SMBus
I2C
Battery Low Indication
System Status (S3 and Reset Outputs)
Power
Single wide input range
+6V to +14V DC (may be module dependent)
RTC Battery
No on-board RTC battery
Option to connect external RTC battery.
Connectors
All shrouded locking ruggedized 2mm pitch headers.
Can be mated to CTI cable set which terminate to panel mountable PC
type connectors.
As well can mated to customer cables sets to terminate to any customer
or MIL type connectors
Mechanical Information
84mm x 55mm (Same as Type 10 mini Form Factor)
CCG010/20: Download 3D model here
Weight
49g (carrier only, no module installed)
MTBF
1253592 hrs / 797.7073 FITs
Operating Temperature
-40°C to +85°C
Warranty and Support
Limited two-year Warranty and Free Technical Support

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 9 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
Product Overview
Block Diagrams
CCG010 Block Diagram
CCG020 Block Diagram

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 10 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
Connector Locations
CCG010 Top View
CCG010 Bottom View

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 11 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
CCG020 Top View
CCG020 Bottom View

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 12 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
Connector Summary
Designator
Connector
Description
P1A
2x5 2mm Locking Pin-Header
GBE1 Connector
P1B
2x5 2mm Locking Pin-Header
GBE0 Connector
P2
2x10 2mm Locking Pin-Header
DisplayPort++ Connector
P3
microSD Card Socket
microSD Card Connector
P4
2x3 2mm Locking Pin-Header
Input Power Connector
P5
1x3 1.25mm Locking Header
RTC Battery Connector
P6
19-Pin 2mm Locking Header
USB 3.0 Connector (CCG020 only)
P7
2x5 2mm Locking Pin-Header
RS-232/485 Connector
P8
220-pin Board to Board Connector
COM Express Type 10 Connector
P9
20-pin Hirose Panel Connector
LVDS Video Connector
P10
2-pin Power Connector
LVDS Backlight Power Connector
P11
Right Angle SATA Connector
SATA 0 Connector
P12
2x10 2mm Locking Pin-Header
Misc/System Connector
P13
2x4 2mm Locking Pin-Header
Audio Input/Output Connector
P14A
2x4 2mm Locking Pin-Header
USB 2.0 Port 1 & 2 Connector
P14B
2x4 2mm Locking Pin-Header
USB 2.0 Port 3 & 4 Connector
P14C
2x4 2mm Locking Pin-Header
USB 2.0 Port 5 & 6 Connector
Jumper Summary
Designator
Jumper
Description
J1
6-position 1.27mm Jumper Block
RS-232/RS-485 Jumper Block
J2
6-position 1.27mm Jumper Block
Misc/System Jumper Block

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 13 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
Detailed Feature Pinouts and Functional Descriptions
COM Express Module
The processor and chipset are implemented on the COM Express Type 10 CPU module, which connects to the
COM Express carrier via a Tyco fine pitch stacking connector.
Function
COM Express interface
Location
P1
Carrier
Connector PN
3-6318491-6
Manufacturer: TE
Connectivity
Mating
Connector PN
3-1827231-6
Manufacturer: TE
Connectivity
Pinout
See Appendix A

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 14 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
Display Outputs
LVDS Video Connector
The COM Express carrier provides dual 18 or 24 bit LVDS display channels via P4, which are connected
directly from the COM Express module.
Function
LVDS Graphics
Location
P9
Carrier
Connector PN
DF19G-20P-1H(54) - Manufacturer: Hirose
Mating
Connector PN
DF19-20S-1C - Manufacturer: Hirose
Pinout
Pin
Signal
Description
1
+3.3 VCC_PNL
Panel Power
2
+3.3 VCC_PNL
Panel Power
3
GND
Digital ground
4
GND
Digital ground
5
LVDS_A0_N
Channel A Data
6
LVDS_A0_P
Channel A Data
7
GND
Digital ground
8
LVDS_A1_N
Channel A Data
9
LVDS_A1_P
Channel A Data
10
GND
Digital ground
11
LVDS_A2_N
Channel A Data
12
LVDS_A2_P
Channel A Data
13
GND
Digital ground
14
LVDS_CLK_N
Channel A Data
15
LVDS_CLK_P
Channel A Data
16
GND
Digital ground
17
+5 VCC_PNL [1]
Backlight Power
18
+5 VCC_PNL [1]
Backlight Power
19
GND
Digital ground
20
BKLT Control [2]
LED ADJ
[1] –+5V_VCC_PNL –This voltage can be enabled or disabled to the display via Jumper J2 position C.
[2] –BKLT Control –This signal can be connected to the COM Express backlight control pin or to GND via Jumper J2
position D and E.

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 15 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
LVDS Backlight Power Connector
The COM Express Type 10 Mini Carrier carrier is equipped with a LVDS backlight inverter power supply
connector. This power supply is designed to power HDA700LPT-GHL (or similar screen type) which has 13
parallel strings of 3 series white LEDS. Each white LED has a Vf of around 3.3V.
Function
LVDS backlight Inverter power
Location
P10
Carrier
Connector PN
SM02B-BHSS-1-TB - Manufacturer: JST
Mating
Connector PN
BHSR-02VS-1 (N) - Manufacturer: JST
Pinout
Pin
Signal
1
VA LED
2
VK LED

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 16 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
DisplayPort ++ (DDI) Video Connector
The COM Express Type 10 Mini Carrier features a DisplayPort++ connector. This can be configured to output
DisplayPort, HDMI/DVI or even VGA through the use of a dongle.
The configuration of each interface is setup via the COM Express module’s BIOS settings. Refer to the COM
Express module’s documentation for more details.
Function
Main Input Power
Location
P4
Carrier
Connector PN
98424-G52-20LF - Manufacturer: FCI
Mating
Connector PN
10073599-020LF - Manufacturer: FCI
Pinout
Pin
Signal
Description
1
DP0+
DisplayPort Pair 0
2
DP3+
DisplayPort Pair 3
3
DP0-
DisplayPort Pair 0
4
DP3-
DisplayPort Pair 3
5
GND
GND
6
GND
GND
7
DP1+
DisplayPort Pair 1
8
DPAUX-
DisplayPort Auxiliary Pair
9
DP1-
DisplayPort Pair 1
10
DPAUX+
DisplayPort Auxiliary Pair
11
GND
GND
12
GND
GND
13
DP2+
DisplayPort Pair 2
14
DP.HPD
Hot Plug Detect
15
DP2-
DisplayPort Pair 2
16
GND
GND
17
GND
GND
18
GND
GND
19
DP_PWR
DisplayPort Power (+3.3V)
20
DP_AUX_SEL [1]
Auxiliary Selection
[1] –For DP_AUX_SEL –Cable assembly must tie high (+3.3V) for HDMI/DVI output and low (GND) for DisplayPort
output.

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 17 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
HDMI / DVI / VGA
The COM Express Type 10 Mini Carrier’s DisplayPort++ connector can be used for display outputs other than
DisplayPort. The use of HDMI, DVI or VGA can be done through a simple dongle or cable assembly like the
ones shown below. These can be purchased from any OEM vendor (such as www.startech.com ) or directly
through Connect Tech. Note: Some newer processor series like the Intel Baytrail can actually output
proper TMDS signaling, so no external dongles are needed in this case. TMDS actually comes out
directly from the module and carrier.

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 18 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
USB
USB 2.0 Port Connectors
The COM Express Type 10 Mini Carrier has 6 external USB 2.0 ports. Each of these are directly sourced from
the COM Express Type 10 module and do not go through any external hubs or bridges.
Function
USB 2.0
Locations
CCG010:
P14A - A signals = Port1, B signals = Port2
P14B - A signals = Port3, B signals = Port4
P14C - A signals = Port5, B signals = Port6
CCG020:
P14 - A signals = Port2, B signals = Port3
Carrier
Connector PN
98424-G52-08LF - Manufacturer: FCI
Mating
Connector PN
10073599-008LF - Manufacturer: FCI
Pinout
Pin
Signal
Description
1
A-VBUS
Port A Power (+5V)
2
B-VBUS [1]
Port B Power (+5V)
3
A-D-
Port A Data Pair
4
B-D-
Port B Data Pair
5
A-D+
Port A Data Pair
6
B-D+
Port B Data Pair
7
A-GND
Port A GND
8
B-GND
Port B GND
[1] –B-VBUS –This voltage can be disable for USB Client mode on USB port 6, just installing jumper J2 position B.

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 19 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
USB 3.0/2.0 Port Connectors
The maximum configuration for a Type 10 COM Express Modules allows for 2 USB 3.0 Ports with integrated
USB 2.0 Ports. However most modules currently on the market only expose a single USB 3.0 Port. The USB
3.0 signals are sourced from the COM Express Module, and run through a Pericom Semiconductor
PI3EQX7502AIZDE re-driver.
Over current protection, power supply filtering and ESD protection is also provided.
Function
USB 2.0/3.0
Location
P6
Type
Intel USB 3.0 Internal 19-pin Connector
http://www.intel.com/content/www/us/en/io/universal-serial-bus/usb3-internal-
connector-cable-specification.html
Carrier
Connector
PN
ABA-USB-152-K01 –Manufacturer: Lotes
Mating
Connector
PN
Any USB 3.0 20-pin Internal Cable or Connector
CTI PN: CBG131
PUB200-2611-01-00 –Manufacturer: ICT-Lanto
Pinout
Pin
Description
Pin
Description
1
Port A - VBUS
20
-
2
Port A - SSRX-
19
Port B - VBUS
3
Port A - SSRX+
18
Port B - SSRX-
4
GND
17
Port B - SSRX+
5
Port A - SSTX-
16
GND
6
Port A - SSTX+
15
Port B - SSTX-
7
GND
14
Port B - SSTX+
8
Port A - D-
13
GND
9
Port A - D+
12
Port B - D-
10
-
11
Port B - D+

COM Express Type 10 Mini Carrier Manual
Users Guide
www.connecttech.com
Document: CTIM-00120
Revision: 0.12
Page 20 of 44
Connect Tech Inc. 800-426-8979 | 519-836-1291
Date: 2018-01-05
10/100/1000 Ethernet (GBE) Connector
The COM Express carrier features dual 10/100/1000 Ethernet Ports.
GBE Port 0 (P21B) is coming directly from the COM Express module.
GBE Port 1 (P21A) is coming from an Intel 82574 PCIe PHY Controller located on the carrier.
Function
LAN Connector
Locations
P21A, P21B
98424-G52-10LF - Manufacturer: FCI
Mating
Connector PN
10073599-010LF - Manufacturer: FCI
Pinout
Pin
Signal
Description
1
MX1-
Ethernet Pair 1
2
MX1+
Ethernet Pair 1
3
MX2-
Ethernet Pair 2
4
MX2+
Ethernet Pair 2
5
SHELL
RJ Shell Connection
6
SHELL
RJ Shell Connection
7
MX3-
Ethernet Pair 3
8
MX3+
Ethernet Pair 3
9
MX4-
Ethernet Pair 4
10
MX4+
Ethernet Pair 4
Software Support for the Intel 82574
Additional drivers will be needed to properly operate the GBE Port 1 on the COM Express carrier.
These drivers can be downloaded directly from Intel website from the below link:
http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Ethernet+Components&Produc
tLine=Ethernet+Controllers&ProductProduct=Intel%C2%AE+82574+Gigabit+Ethernet+Controller