Connects2 CT23MB26L User manual

CT23MB26L
Double DIN Fitting Kit for
Mercedes Benz Vehicles
APPLICATION
FEATURES
Mercedes Benz E Class (W212) 2009 - 2012
Compatible with Left Hand Drive Vehicles Only
• Allows for the installation of a double DIN aftermarket stereo
• Includes panel for relocation of OEM buttons
• Includes mounting brackets and tting accessories
• Finished in black to match vehicle dashboard
The information provided in this document is subject to change without notice due to manufacturer changes and/or improvements to the product/s. This
instruction manual is based on documented data and research. The manufacturer of this product cannot be held responsible for any changes made to the
vehicle by the manufacturer or damages that may occur through the installation of this product in accordance with the steps outlined herein.
Note: Application data is subject to change at any time
DISCLAIMER
CT23MB26L_IG_en-GB_v1
RECOMMENDED TOOLS
• Panel Removal Tool • Screwdriver
i. Button Relocation Panel
ii. Relocation Panel Bracket
iii. Button Retention Cable
iv. Double DIN Fascia Panel
v. Left/Right Radio Brackets
vi. Screws
- 1/4” Self Tapping (x2)
- M5 8mm (x4)
- 3.8” Self Tapping (x6)

2CT23LR08_IG_en-GB_v1
PRIOR TO INSTALLATION
INSTALLATION GUIDE
Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be
free of moisture and away from heat sources. Please ensure that the correct tools are using during the installation to avoid
damage to the vehicle or product. Connects2 can not be held responsible for the installation of this product.
1. Use a panel removal tool to remove the air vent
panel (Fig. A). Lever the clip out inside the vents as
shown (Fig. B).
2. Unplug the blue connector to the air vent controls
(Fig. C).
3. Partially unscrew the two (2) screws on top of
the head unit. Unscrew each screw half way and
then push the screw down. This will unlock the OEM
head unit bracket assembly (Fig. D).
DASH DISASSEMBLY
4. Remove the head unit and unplug all connections,
including the connector attached to the fascia panel
(Fig. E).
5. Remove the OEM fascia panel (Fig. F).
Included in this kit:
1x Button Relocation Panel
1x Relocation Panel Bracket
1x Button Retention Cable
1x Double DIN Fascia Panel
1x Left Radio Bracket
1x Right Radio Bracket
2x 1/4” Self Tapping Screw
4x M5 8mm Screw
6x 3.8” Self Tapping Screw
Fig.A
Fig.B
Fig.C

3
Need help? Visit support.connects2.com/tickets/technical
CT23LR08_IG_en-GB_v1
INSTALLATION GUIDE
6. Connect the black connector of the Button
Relocation Lead (Fig. G) to the white OEM connector
that was unplugged from the fascia panel in Step 4.
Feed the cable up through the fash so that the white
connector can plug into the button panel.
7. Mount the supplied radio brackets to the right
and left sides of the aftermarket head unit (Fig. H).
8. Insert the head unit and wiring assembly into the
dashboard. The head unit can be guided into place
via the rails as a reverse of Step 3.
Test the head unit for correct operation and move
on to button relocation panel assembly.
KIT ASSEMBLY
Fig.H
Fig.G
Fig.F
Fig.D
Fig.E

4CT23LR08_IG_en-GB_v1
INSTALLATION GUIDE
BUTTON RELOCATION PANEL ASSEMBLY
9. Assemble the button relocation panel. Insert the
buttons into the panel and insert the assembly below
the top lip and click into place. Screw the bracket to
the panel using the four holes on the back (Fig. I).
10. Screw the small plastic brackets (circled, Fig. J)
into place. The bracket with two dots should be tted
to the side closest to the steering wheel.
11. Screw two screws into the bottom of the
bracket (Fig. K).
12. Connect the panel to the vehicle using the OEM
connector. Once working, insert the relocation panel
into the dash to complete the installation (Fig. L).
Fig.I
Fig.J
Fig.K
Fig.L